All Available Parts - 1969 Ford Mustang

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Used wiring harness assembly specific to 1969 Mercury Cougar or Ford Mustang with H code 351W-2V or M code 351W-4V engines. Jumper harness about 9-1/2 inches long. Goes between the cowl plug for the engine gauge feed harness, and the engine gauge feed harness. Special with a 2 ohm resistance wire for the temperature gauge / sending unit. We believe that this wire harness was used specifically with the factory installed temperature sending units for 351W engines in 1969. Ford part...

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914. Ford Part # C9ZZ-10C914-A

Used side marker / rear reflector for the 1969 Mercury Cougar or Ford Mustang Part of Ford part #C9AZ-15A201-C My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our...

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

Finally a fast easy way to hook up the Pertronix Ignitor©! The Ignition Power Relay installs next to the starter solenoid with a supplied self-drilling, self tapping screw. Each wire is the right length and comes with the correctly sized terminal already Installed. Simply connect two wires at the solenoid and connect the Ignitor to the red power wire. The Pertronix Ignitor© is a 12 volt device that must be powered during crank and run. Many installers mistake the coil positive for a 12 volt...

This is a replacement relay for the discontinued original FoMoCo relays.  It does not appear in the same form factor, but will work just fine. The original is a metal cased unit, the replacement is plastic.  Original relays are marked either C7ZA-3E553-A (1967) or  C8ZA-3E553-A (1968 & 1969) on the mounting tab. Click Here to Download Instructions (340Kb pdf). Replaces Ford Part # C7ZZ-10B926-A or C8ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at...

Made by the original supplier! Replaces Ford part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.

Here is a helpful "How To" youtube video on how to replace your ignition switch.

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best. We recommend our good used units which you can get right here.

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good used windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. 1969 has the flat spot oriented at the bottom. Ford part numbers: C9ZZ-17C491-A, C9ZB-17C491-A.

Reproduction ignition switch repair pigtail for your 68-69 Cougar and Mustang. This pigtail is not going to be a good fit, but if you choose this as your replacement, keep in mind that although this pigtail has an extra long resistor wire, do not splice into it or cut it down. Its resistance is dependent on its full length. This is a  cheap, inexpensive replacement, but we don't recommend it and would highly suggest going with one of our used pigtails instead.  NOTE - We've...

Used ignition switch for the 68 - 69 Cougar or Mustang. Does not include cylinder or keys.Here is a helpful "How To" youtube video on how to replace your ignition switch.

For AM radio optional rear speaker. Ford part number C9ZB-18A900-BOverall length: 11' 7"

This harness connects the rear speaker harness to the fader switch. Ford part number C8GA-18A900-BOverall length: 44"

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

Used engine lift hook or hoist bracket for all 1969-70 351W engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351W-2V and M code 351W-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also sell...

Used engine lift hook or hoist bracket for all 1968-69 390 engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. X code 390-2V, S code 390-4V, and W code 427-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We...

Used oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Reproduction oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Featured in this kit are all the basic items you need to convert your small block 1969 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small block...

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang 

A needed part for giving your car a tune-up.

Reproduction Distributor Condensor for the 1967 - 1973 Mercury Cougar and Ford Mustang

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

Used Autolite Distributor for 1968 390-4V and 1968-69 428CJ for the Mercury Cougar, Cyclone or Ford Mustang, Torino.  Ford part number  C8OF-12127-D.  

Used core distributor for 1969 Mercury Cougar and Ford Mustang with H code 351-2V and aNY transmission. Core distributors will have correct stamping of C9OF-M. Original Ford part number C9OF-12127-M.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of C9OF-T. Original Ford part number C9OF-12127-T.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar or Ford Mustang with 428CJ engine with thermactor smog system. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1969-70 Mercury Cougar Eliminator or Ford Mustang with Boss 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar Eliminator or Ford Mustang with 351W engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Black spark plug boots on this set.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with S code 390-4V and automatic transmission. Core distributors will have correct stamping of C7AF-AC. Original Ford part number C7AF-12127-AC. Current unit has a date of 9B10, or February 10, 1969. Stamped C7AF-12127-AC.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Used coil mounting bracket. This is the later Big Block V-8 version starting 1969. Found on 390 and 428CJ cars.We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. This version is for big block V-8's, and has a 'flat' strap on the bottom, earlier versions had an additional reinforcing 'C' channel on the bottom. Probably used starting in 1969. Some have...

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering is dated 8-67 Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and...

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. 1969-70 Mercury Cougar Eliminator with Boss 302 and 1969-70 Ford Mustang with Boss 302 engines.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with single nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with dual nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar Eliminator or Ford Mustang with 390 or 428CJ engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Black spark plug boots on this set.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Windsor engine rated at 250 Hp with 9.5:1 compression ratio in 1969. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory M code 351-4V V-8 engine. 351 Windsor engine rated at 290 Hp with 10.7:1 compression ratio in 1969. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7C29 March 29, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

This block has been professionally hot tanked and mag checked. No cracks. Dated 7C16 March 16, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship through any conventional methods (USPS, UPS etc). Along...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6L15, November 15, 1966.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7M27, December 27, 1967.  Used 0.030 over bore 4.080" Ford 390 engine block. Years ago, it looks to have been fresh machined, with new freeze plugs. No paperwork, bare block. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6C5, March 5, 1966.  Used 0.030 over bore 4.080" Ford 390 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Used coil mounting bracket. This version of the bracket is probably the most common. Typically this version was used on small block V-8's in 1967-68. This version has the 'rails' to give it strength. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to...

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

THIS ITEM CARRIES A $65 REFUNDABLE CORE CHARGEAll 1969 Mercury Cougar 351W engines. Includes both the H code 351-2V and the M code 351-4V engines. The 1969 351 Windsor harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-3/8 inches, and 3/4 inches thick. Ford part number C9OZ-6316-A. Has the timing marks on rim. Refundable $65.00 core charge when rebuildable C5AE-6316-A harmonic balancer is received by WCCC. *Note - Not...

Includes both the H code 351-2V and the M code 351-4V engines. The 1969 351 Windsor harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-3/8 inches, and 3/4 inches thick. Crank shaft balancer, crankshaft dampener, harmonic balancer. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option...

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines 1968 - 1970 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, and 1-1/16 inches thick. Has the timing marks on rim.  The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

Reproduction PCV Hose with Ford Logo for the 1969 Mercury Cougar or Ford Mustang with 351 engines. Fits from the PCV valve in the valve covers to the factory Ford carburetor spacer plate.  Approximately 3/8" inside diameter but it will stretch to fit over a 1/2" PCV valve fitting.  Keep in mind that it will stretch easier if warmed.

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/29/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 12/5/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/67

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/25/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 8/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/28/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 1/26/70

Reproduction 14" length economy breather cap hose for the 68 - 70 Cougar or Mustang.