All Available Parts - 1968 Mercury Cougar

NOS GT-E Fender badges. Sold as a pair, driver side shows a C7WX-16099 casting number and the passenger side shows a C7WX-16098 number.

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fits many 1967 - 1968 Full size Mercury cars and 1967 - 1969 Mercury trucks. This emblem measures 6 3/8" total width and the "M" is 2 1/8" tall. The bottom mounting studs located on the letter "M" and "Y"...

This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

This Mercury script emblem is mounted onto the driver side fender extension. This is an original part still in the Ford box, engineering number on the back of the emblem reads C7WB-16098-A, Ford part number is C7WY-16604-A.

This adhesive plaque was placed in front of the shifter on XR7-G models with a factory installed four speed manual transmission. The XR7-G shift knob had a walking Cat on the face of the knob instead of a shift pattern.

These always are peeling. Located on the right side on the dash face...

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

There are several differences between this NOS decal and the good quality reproduction we offer. First off the red "7" is darker, second the "XR" is more brilliant, third is when you run your finger nail over the tiny raised ridges the reproduction makes a audible zip sound and the NOS does not, fourth is there is no adhesive backing on the NOS decal and there is on the reproduction, fifth is the reproduction is made of a much heavier aluminum stock than the NOS and lastly the NOS fits in the...

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Complete assembly minus the cylinder. Only the 68 was marked NOS, the 1967 XR7 just had the COUGAR decal. Click on images to enlarge. ...

Rare Cougar only GT emblems. The Mustang GT emblems had different stud locations. These were used on 1968 Mercury Cougar GT models.  This emblem shares the exact same pin locations with the 1968 6.5Litre emblem, so the factory could punch holes and installed the tubular nuts in the fenders of all S and X code Cougars, allowing either emblem to be installed. The 1967 GT emblems have an entirely different stud placement from these 1968 only badges. Letter "G" is Ford part...

After waiting several months, these reproduction 1967 - 1968 Mercury Cougar Deck Lock (Trunk Lock) covers are now finished! The reproduction chrome cover shown here sports a very rare original Ford, NOS XR7 decal. The NOS decal is different from our reproduction in three subtle areas. First the number "7" is a darker, richer color, second the decal fills the recessed area better and third the detail in the black area is a little different than our reproductions. Great for the person that loves...

The later run XR7-G emblems we offer are really quite nice, but they are all just a tad smaller than originals. This is almost impossible to detect unless you have a reference point. The lock cover does in fact provide a reference point in that if you use a new emblem you will have a noticeable gap around the perimeter of the emblem. In years past, nobody really was concerned, but now that the XR7-G can be worth six figures in pristine condition, it matters. I put a used emblem behind this NOS...

Rare find in NOS form! Used only on the 1967 and 1968 Mercury.Ford part number C7AZ-17632-A

The item pictured here is our reproduction XR7-G trunk deck lock cover with a NOS emblem. Big difference in fit compared to the current version of this emblem. Great for the XR7-G owner wanting to set his "G" apart from the rest of the pride... Click on images to enlarge. The emblem shown on the bottom is the NOS emblem sold through Ford back in the day and the top version is the one being made today by the OEM supplier.  Molds wear out, materials used differ, process changes over the...

Regardless of what you have been told these emblems were never chromed. We do not have any of these in stock, probably will not get any more but we post this so as to give you a reference as to what color they should be.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.96 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with S or R code engines. Ford part number C8ZZ-9A702-B. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 13.54 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Application is 1968 Mercury Cougar and Ford Mustang with 390-4V or 428CJ engines and speed or cruise control. Original Ford part number C8ZZ-9A702-D.*Note - For use with factory cruise control.

Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.

For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.

For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.

Also correct for some 1967 models with proportioning valve at front

This reproduction power drum brake line kit is for Mercury Cougars and Ford Mustangs equipped with the 8 inch rear end and 28 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Application 1968 Mercury Cougar and Ford Mustang  with 289 or 302 engines and cruise or speed control. Ford part number C8ZZ-9A702-C. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with X-code 390-2V engines and speed or cruise control option. Original Ford part number C8WY-9A702-B. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - For use with factory cruise control.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 427-4V GT-E Cougars with automatic transmission. We suspect that this bell crank may be slightly different than the 390/428CJ version due to the Police Interceptor intake manifold?Ford part # C8ZZ-9725-A.*TRIVIA* All W code 427-4V GT-E's could only be ordered with an automatic C6 transmission.

Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.

Inner front bolt, long length to clear sound deadener. Used in conjunction with a thick, gold spacer washer.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Used seat belt bolt washer for the Mercury or Ford.

Replaces Ford Part # C8AZ-2B164-A Sold individually

Used stamped nut for attaching the tail light bezels to the tail light housings. This is a 8-32 nut, with a 11/32" hex and is intended for the 8-32 threaded studs attached to the tail light bezels on any 1967-68 Mercury Cougar. Sold individually, 10 per side, or 20 per car.Replaces Ford part number 45203-S.

These little clips are what were used to fasten the dash face pad to the dash bezels on a 1968 standard or decor level Cougar. They are very difficult to come by and we have yet to find a suitable substitute. We suggest that if you need more than a few of these clips that you consider using strips of adhesive Velcro in lieu of these clips as Velcro holds the fragile aluminum trim more evenly against your bezels and is easier to install and remove for future maintenance. *NOTE* There are 13 of...

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang.Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

Rear seat belt bolt, four per car used in conjunction with two red washer / spacers. 13/16" hex head, 1-1/4 inch bolt with a 3/16 inch shoulder. Can be either smooth headed or have a Heavy or Light "A". There is another version of this same bolt with a smooth head and no markings.

Two of these clips per side are required to hold the interior padded pillar pads the the "A" pillars on your 1968 Cougar.Replaces Ford part number 381896-S2.

Here is a pair of cast aluminum running cat valve covers for the 1968 Mercury Cougar XR7-G with the F code 302-2V or J code 302-4V engine. Original valve cover, not a reproduction. Originally cast by Shelby American Inc.Ford part # C8WY-6582-B, Shelby American part number S7WE-6582-B.

C8WY-6582-C  Cast aluminum running cat valve cover for 1968 Mercury Cougar XR7-G with X code 390-2V , S code 390-4V, or R code 428CJ engines. Original valve cover, FE running cat valve covers were not side specific. One cat will face forward and one will face backwards on your Cougar. Originally cast by Shelby American Inc #S7MS-6582.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

Includes drain plug.

The oil filter made by the original Ford supplier.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

Developed on a 3D printer, good fit but notice the texture is not the same. Four speed and Automatic transmission use the same bezel.

This is a rare find... This used 4 piece bracket set was taken from a June 17th built 1968 390 X code Cougar with factory dual exhaust. These are much cleaner used parts than you will see in other regions as they have never been exposed to road salt. We no longer sell them with the bolts and clamps, this is a sample photo of one of several sets we have in stock as of 10-12-07. The parts you receive may actually be in better condition except for the rubber parts which are often worse. The...

This is the harder to find tail pipe hanger as it was only used on dual exhaust cars. Will have usable but cracked rubber. Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1969 dual exhaust Cougars, all engines. Ford part number C8WY-5260-B.

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Used on the optional 1968 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1968 Torino and Mustang. Also used on the 1969 Eliminator 12 hole wheel so as to match the brushed center cap. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most...

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator, 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. WCCC is the only retailer offering these at present. Sold individually. Replaces Ford part number C8ZZ-1210-A. ...

Mounts to the rear of a 'turbo' style muffler. Left side bracket. 289, 302, 390, 427, 428, all with dual exhausts. Ford part number C8WY-5260-E. *Early production prior to 11-1-1967

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.

Used clutch spring bracket that attaches to the brake / clutch hanging bracket. All 1967-68 Mercury Cougar and Ford Mustang with manual transmissions. Replaces Ford Part #: C7ZZ-7535-B.

Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.

The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford Mustangs with a 3 or 4 speed manual transmissions. When people part out early Cougars they often leave this little detail item behind not fully understanding its function or rarity. Stood on end its length at the very longest point is 3 1/4". Its function is to but tension on your equalizer bar when it is in its...

This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. Includes both Pressure and Return hose that connect to the control valve. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against...

[No Description Provided]

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang with or without Power Steering Cooler.  Be sure to select the option to...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

OEM routed power steering hose kit for the small block 1968. Includes the upper and lower hose.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Used bezel for the dual post head rest for the Mercury Cougar XR7. This bezel measures 4" long and is correct for the XR7. Due to extra thick seat foam, the XR7 uses this taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was known as Rotunda. Down deep near the threads is a molded hex shape that allowed a tool to tighten without...

Reproduction set of color coded A/C rubber hoses, two T connectors and vacuum diagram.

Core bench seat for the 1968 Mercury Cougar or Ford Mustang equipped with decor interior. 1968 bench seat without optional headrests, but with seat seat back release latches. The foam will almost always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Keep in mind 68 and 69 are identical except for how the head rests attach. You can easily add head rests from 69 buckets and bolt them to a 68 pair of buckets or bench if you have all the...

Note: The set you receive may not be the ones pictured and will usually be in better condition than shown. The chrome bezels will all be in good matching condition, unlike the blemished one in the picture. Call if you need more details or to check inventory on colors. Used pair of dual post head rests for the Mercury Cougar or Ford Mustang. These ultra rare head rests were an option in 1968 only and may come with some slight blemishes. Your 1968 Mustang / Torino / Thunderbird / Cyclone seat...

Good used headrest with no mounting hardware included. No cracks. We never have more than one of these in stock as a single so we most likely will not be able to produce the color of your choice but it never hurts to ask! Basic Ford part number for this item is C8AB-62611-A08. The "08" suffix part of the number may refer to a specific color.

Currently out of stock. Do you have a pair for sale? Let us know! Four required per car, bolts to the back side of the upper portion of your 1968 seat frame. According to the 1968 Cougar assembly manual the Ford part number is C8ZB-65610B10. This part has an adjustment to fine tune the headrest post alignment.

Used bezel for the dual head rest found in the Mercury Cougar or Ford Mustang. This bezel measures 3 1/2" long and is correct for all 1968 models that use this part (including Shelby and Ford Mustang except the XR7 Mercury Cougar. Due to extra thick seat foam, the XR7 uses a taller bezel. Good used part with no peeling chrome or obvious cracks (may have hairline crack in threaded area). Ford originally had a special tool for installing and removing these guide sleeves. Ford tool division was...

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Ford part number C8AZ-6A312-A. Application 390-2V, 390-4V engines, and 428 Cobra Jet with air conditioning. Power steering optional, with dual alternator belts. Ford casting number C8AE-6312-A. Triple sheave 68 crank pulley.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

NOS Air conditioning belt tension pulley for Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968.  Ford part # C7AZ-8678-B. NOTE* Send in your old core for a credit toward the purchase of this NOS pulley. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

[No Description Provided]

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...