Home > 1968 Mercury Cougar
All Available Parts - 1968 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 5201-5300 of 5492
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 11-0411 -
Grade A used 1968 Mercury Cougar air conditioning chrome bezel, naked as shown. Very minor blemishes, almost insignificant as shown. No extra parts included, levers and switches available. Does not come with the 1968 only detachable air vent. The 1968 Cougar electrical assembly manual indicates that this is part of C8WA-19A976-F Register and Control assy. (Bright Finish). Bright finish is Cougar, Ford Mustang bezels had black pebble grain or wood grain finishes attached. Ford casting number on...
Availability: Out of Stock
Item #: 11-0355 -
Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...
Availability: Out of Stock, Discontinued
Item #: 32594 -
Reproduction 15x8 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...
Availability: Out of Stock
Item #: 11-0012 -
Used air conditioning vent for any 1968 Mercury Cougar or Ford Mustang with factory installed A/C. These are different than the 1967 A/C vents. For 1968 the vents detached from the main housing for safety reasons. These were meant to 'break away' in the event of an accident. These attach to the housing with a spring, spring sold separately. Grade A is in limited quantities and will have very good chrome, there will be some minor blemishes found under close scrutiny. B grade versions also...
Availability: Out of Stock
Item #: 11-0063 -
Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.
Availability: Out of Stock
Item #: 23979 -
Passenger side air conditioning register vent with slight manufacturer blemishes. See photos for details.
Availability: Out of Stock
Item #: 24534 -
Used air compressor to intake manifold tubular steel bracket. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell, there is no difference from 1967 to 1968 pieces.Ford part # C8ZZ-2889-A
Availability: Out of Stock
Item #: 20557 -
Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.
Availability: Out of Stock, Discontinued
Item #: 14752 -
9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14x6" styled steel wheel with a chrome outer rim and an original argent finish between the spokes on the center for your Mercury Cougar. This is a great...
Availability: Out of Stock
Item #: 14743 -
9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14x7" styled steel wheel with a chrome outer rim and an original argent finish between the chrome spokes on the center. No, Mercury never offered them in a...
Availability: Out of Stock, Discontinued
Item #: 23433 -
9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 15x8" styled steel wheel with a chrome outer rim for your Mercury Cougar. This unit comes with 4.5" back-space, unless ordered otherwise. Center caps, trim...
Availability: Out of Stock
Item #: 11848 -
This is a very rare wheel found only on early XR7-G models. Soon after being put into service, the wheels were found to have multiple short-comings including flexing, cracking and lug seating problems. They were officially recalled and replaced with the Kelsey Hayes 5 spoke SS wheel. The original manufacturer of the XR7-G wheels was Trans American Products. The style used on the XR7-G was known as the "Rader". Only a few sets of these are known to be mounted on original xr7G models today....
Availability: Out of Stock
Item #: 19002 -
Original Rader Wheels as installed on 1968 Mercury XR7-G special edition cars. These are the wheels that were intended and the ones shown in the brochure, posters, and magazine publications. These are the cast and chromed lace designed wheels made by Rader. Set of 5 used 14 x 6 wheels, 4 are in nice condition, the 5th has some chrome plating issues. Included are the caps and cones, which were copied from an original. We are also offering 20 lug nuts, and 20 newly machined lug...
Availability: Out of Stock
Item #: 16216 -
This set of four wheels is not correct for a xr7G Cougar as they are 15" and the originals were 14". You may find that more tire options are available for a 15" tire. These wheels have been tested and have found to be true. The Rader wheels were recalled by Ford, shortly after the first XR7-G cars were produced. Your Mercury dealer would have installed the common 1968 Cougar style steel wheels as replacements.
Availability: Out of Stock
Item #: 24522 -
Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...
Availability: Out of Stock
Item #: 16006 -
Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1968, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...
Availability: Out of Stock
Item #: 30495 -
Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand.These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...
Availability: Out of Stock
Item #: 30521 -
Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....
Availability: Out of Stock
Item #: 14746 -
9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. No, Mercury never offered wheels in a 15x7" for an early Cougar... We now sell more of these custom made SS wheels than the original 14x6" version. Not only do they look...
Availability: Out of Stock
Item #: 24474 -
Used 14x6" styled steel wheel for your Mercury Cougar. This unit has a total width 7", a 4" backspacing, and a 1- 13/16" center hole. This is the service replacement number and it will fit all 1967 and newer Cougars with or without disc brakes. Slightly wider than the 1967 counterpart. Shipped bare without center cap or trim ring. We have these wheels in various conditions with minor blemishes and they are subject to availability.Ford part # C8WY-1007-A.
Availability: Out of Stock
Item #: 24421 -
Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...
Availability: Out of Stock, Discontinued
Item #: 12821 -
New aluminum 17x8" Magnum 500 wheel with a 4 inch backspace for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes the center cap. Lug nuts sold separately, get them here.
Availability: Out of Stock, Discontinued
Item #: 26918 -
SUPPLIER IS BACKORDERED ON THIS WHEEL UNTIL FURTHER NOTICE.New aluminum 15x7" Magnum 500 wheel with a 4 inch backspace for your Mercury Cougar or Ford Mustang. Includes generic plastic center cap.
Availability: Out of Stock
Item #: 30258 -
Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 25088 -
Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.
Availability: Out of Stock
Item #: 23857 -
This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...
Availability: Out of Stock, Discontinued
Item #: 18939 -
Reproduction 14x6" Magnum 500 wheel for the Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant, but it holds up great year after year. You may save a few dollars buying the other brands out there, but why? We now have Magnum 500 caps that sport the Mercury Logo with multiple background colors and the walking cat caps as well. Center caps and lugs are sold separate.
*NOTE* Please...
Availability: Out of Stock
Item #: 18940 -
Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...
Availability: Out of Stock, Discontinued
Item #: 11693 -
Reproduction 15x6" Magnum 500 wheel for the Mercury Cougar or Ford Mustang. Here is an oddball you will probably not find advertised elsewhere... The total width of this wheel is 6 7/8" with a 4" backspace.Center caps and lugs are sold separate. *NOTE* Please allow 4 to 5 weeks for delivery.NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not...
Availability: Out of Stock
Item #: 18943 -
These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.
NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...
Availability: Out of Stock, Discontinued
Item #: 42409 -
QUALITY HAS GONE DOWN ON THESE CAPS, UNTIL THE SUPPLIER CAN CORRECT THE ISSUE, WE WILL NO LONGER HAVE THESE AVAILABLE. Correct reproduction XR7-G chrome center caps with the correct magen ta background and chrome XR7-G logo that includes three part mounting hardware. These are die-cast just like the originals, other reproductions out there are made on a lathe with aluminum stock. Sold individually. Ford part # C8WY-1130-F. *NOTE* When installing these die cast center caps, keep in mind over...
Availability: Out of Stock
Item #: 16801 -
The only reason you would buy an original used unit is that you would want to match your existing original caps. The reproductions we carry are actually much better quality than the originals, as they will never fall off. Chrome center cap with black background and chrome Mercury man logo. Came from the factory on 1967 and 1968 Mercury Cougars with Styled Steel Wheels, but will work on any 67-70 with Styled Steel Wheels.Fits the following models with style steel wheels:1967 Mercury Cougar1968...
Availability: Out of Stock, Discontinued
Item #: 26740 -
QUALITY HAS GONE DOWN ON THESE CAPS, UNTIL THE SUPPLIER CAN CORRECT THE ISSUE, WE WILL NO LONGER HAVE THESE AVAILABLE.Reproduction chrome center caps that feature a magenta background and a chrome XR7-G logo for the Mercury Cougar. The center caps are die-cast like the originals were, other reproductions out there are made on a lathe with aluminum stock. These units are sold individually. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing...
Availability: Out of Stock
Item #: 18530 -
Used original chrome center caps with magenta background and chrome XR7-G logo for the XR7-G styled steel wheel.
Availability: Out of Stock
Item #: 24476 -
Notice the blemishes on this NOS cap? This is very typical of what we see on many NOS caps. This chrome XR7-G center cap with magenta background and chrome XR7-G logo is designed to fit the RADER chrome cone adapter or mount directly to the 1968 chrome style steel wheel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or...
Availability: Out of Stock
Item #: 11827 -
This XR7-G center cap adapter cone was used in conjunction with the RADER wheel and is needed to mount the center cap to the aluminum centered wheel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know...
Availability: Out of Stock
Item #: 42138 -
Set of 4 Chrome center caps with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. Fits the following models with Magnum 500 wheels: 1969 Mercury Cougar 1970 Mercury Cougar These will work with multiple brands / styles of after market wheels as well. Sold individually. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain...
Availability: Out of Stock
Item #: 19957 -
Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:
Availability: Out of Stock
Item #: 24245 -
C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.
Availability: Out of Stock
Item #: 24246 -
C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.
Availability: Out of Stock
Item #: 24117 -
Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B grade, due to pits in the chrome. This version is the one held down with 4 screws. Part number C7WB-7262-A is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...
Availability: Out of Stock
Item #: 10955 -
Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C7ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 31098 -
Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B+ grade, due to pits in the chrome. This version is the one held down with 2 screws. Part number C7WB-7262-C is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...
Availability: Out of Stock
Item #: 24863 -
This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...
Availability: Out of Stock
Item #: 24304 -
C7ZZ-7515-D Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Cougar 1967 through 2-15-1968. 390-4V engines only, XR7, XR7-G. Mustang 1967 through 2-15-1968. 390-4V only, GT. Mustang 1967. K code 289 HiPo 4 speed only. GT
Availability: Out of Stock
Item #: 30873 -
Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with 4 speed transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-A or C7ZZ-17260-J. Has captured hold down bracket at transmission. Cable has a rubber hose at the transmission end. These measure out about 76 inches long. Also has a metal sleeve about 10 inches from the speedometer cluster end, Cable clamp? Used condition, will have road grime, and maybe a couple of abrasions or small...
Availability: Out of Stock
Item #: 15254 -
New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.
Availability: Out of Stock
Item #: 22612 -
D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.
Availability: Out of Stock
Item #: 30619 -
This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A
Availability: Out of Stock
Item #: 24510 -
Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C5DZ-6392-B. For use on 289 engines after 2-15-68. This bellhousing is only for use with the 157 tooth flywheel. This bell-housing also requires the use of clutch fork C8OA-7515-A. Shipped bare, no hardware or clutch fork. Replaces Ford part number C8ZA-6394-A.
Availability: Out of Stock
Item #: 16-0068 -
Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C6OZ-6392-B. The latest research shows that the casting number C60A-6394-B bellhousing may have been for 1966-68 Cougar, Mustang, Fairlanes and Comets with an 11 inch clutch disc. Shipped bare, no hardware or clutch fork.
Availability: Out of Stock
Item #: 16-0065 -
This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...
Availability: Out of Stock, On Order
Item #: 26772 -
This pedal assembly is an exact reproduction of the 1967 clutch pedal. It can be used on 1968 with no modifications. Fits all engine applications. Made in the U.S.A.Replaces Ford Part #: C7ZZ-7519-A.
Availability: Out of Stock
Item #: 16-0050 -
Grade A used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This is a real clean rust free cover but if you are wanting to save money, we have grade B's which will have a dent or creases for about half the price. Find the grade B here.Ford part number C3AZ-6366-A. ...
Availability: Out of Stock
Item #: 16-0013 -
Original dipstick tube. Application 1967 - 1969 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number C8ZZ-7A228-A.
Availability: Out of Stock
Item #: 11849 -
RAN-D or RAN-D1 Original equipment 3 speed top loader 3.03 transmission from a 1967 - 1968 Mercury Cougar with engine code C - 289-2V, or engine code A - 289-4V only. Could also have a casting number of RAN-D1. Ford master part number C5ZZ-7003-V.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...
Availability: Out of Stock
Item #: 11851 -
RAT-U Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code F - 302-2V, or engine code J - 302-4V only. Ford master part number C5ZZ-7003-Z.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...
Availability: Out of Stock
Item #: 25687 -
RAT-N1 or RAT-N2 Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code S - 390-4V only. Transmission with casting number RAT-N2 also used during this model year. Ford master part number C8ZR-7003-E. *Note - RAT-N could also be sustituted.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame...
Availability: Out of Stock
Item #: 11343 -
New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.
Availability: Out of Stock, Discontinued
Item #: 15302 -
Replacement transmission pan filter and pan gasket kit. Gasket for the C4 (W Code) transmission. Replaces Ford Part Number: C5ZZ-7A098
Availability: Out of Stock, Discontinued
Item #: 14927 -
OE Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.
Availability: Out of Stock, On Order
Item #: 14928 -
Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.
Availability: In-Stock Item
Item #: 31761 -
The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.
Availability: Out of Stock, On Order
Item #: 13942 -
Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 30871 -
Used speedometer cable from a 1968 Mercury Cougar or Ford Mustang with C4 transmission. These are assembly line used and would have had a Ford number of C8ZF-17260-D or C8ZZ-17260-D. Has captured hold down bracket at transmission. 1968 cables have a rubber ring at the transmission end to hold the hold down clamp. These measure out about 63-1/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested...
Availability: Out of Stock
Item #: 30874 -
Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with C-6 automatic transmission. These are assembly line used and would have had a Ford number of C7ZZ-17260-C. Has captured hold down bracket at transmission. About 66-9/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is good. Tags generally are not present on these. Look at the related items, you may need a firewall...
Availability: Out of Stock
Item #: 30878 -
Used speedometer cable from a 1968 Mercury Cougar or Ford Mustang with speed control or cruise cotnrol. This is assembly line used and would have had a Ford number of C8ZF-17260-E. This measures out about 62 inches long. Has specific screw on end for the speed control servo. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is good. Tags generally are not present on these. Look at the related items, you...
Availability: Out of Stock, On Order
Item #: 14348 -
Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...
Availability: Out of Stock, On Order
Item #: 14349 -
Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...
Availability: Out of Stock
Item #: 20131 -
This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.
Availability: Out of Stock
Item #: 24527 -
The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...
Availability: Out of Stock
Item #: 12931 -
Complete floor shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210A C7ZZ-7A306B C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 30964 -
Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10490 -
Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...
Availability: Out of Stock
Item #: 10489 -
Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This surround or "U" plate was originally attached with heat to pin connectors. To reattach we suggest using glue. This U part attaches to the bottom of the console shifter bezel and shrouds the light. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 20019 -
Mint Condition NOS part for your XR7-G equipped with automatic transmission. Notice the texture or "Fur" on the Cougar. The majority are smooth from the factory. We have no explanation for this variation. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10457 -
1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both
black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D.
Click on images to enlarge. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock, On Order
Item #: 13959 -
Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 16-0075 -
Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...
Availability: Out of Stock
Item #: 12872 -
Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B
Availability: Out of Stock
Item #: 27495 -
NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.
Availability: Out of Stock
Item #: 11009 -
[No Description Provided]
Availability: Out of Stock
Item #: 25930 -
Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct length of power steering hoses.
Availability: Out of Stock
Item #: 13875 -
This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.
Availability: Out of Stock
Item #: 18935 -
Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.
Availability: Out of Stock, Discontinued
Item #: 25931 -
Fits 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.
Availability: Out of Stock
Item #: 24267 -
The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.
Availability: Out of Stock
Item #: 11784 -
Reproduction power steering drop bracket for the Mercury Cougar or Ford Mustang. One must use this part when installing headers with power steering. Because of the way this bracket hangs down, it will get bumped and bumped hard in time. Becasue of this we recommend considerning our premuim version of this bracket, as it is substantially stronger.
Availability: Out of Stock
Item #: 10582 -
This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...
Availability: Out of Stock
Item #: 20340 -
This is one of my all time favorite Mercury Dealer promotional guides. Great detail shots and beautiful photography. This is what the salesman would have handed you in 1967-68 when you inquired about a new Cougar. Rare find, mint condition, very limited quantity. Notice that only the later version had the green insert announcing the mid year changes. Most of our copies do not come with the green supplement. The dealer showroom album lists a January 1, 1968 effective date for the changes...
Availability: Out of Stock
Item #: 14-1000 -
New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver!
Availability: Out of Stock
Item #: 11-0024 -
Heater control bezel for Mercury Cougars without A/C. Assembly includes grade A bezel, you will want to paint with your exact dash color. Check back often, this type and grade of part is seldom in stock very long. Ford part # C8WA-18531-A.
Availability: Out of Stock, On Order
Item #: 41707 -
Concourse Correct 90 degree elbow that attaches to the intake manifold and provides proper clearance for the emission canister and air cleaner housing. Correct for all 1968 S code 390-4V, W code 427-4V and R code 428 Cobra Jet engines.
Availability: Out of Stock, Discontinued
Item #: 12894 -
Economy reproduction sponge foam grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years.
Availability: Out of Stock
Item #: 11-0446 -
This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...
Availability: Out of Stock
Item #: 11-0002 -
Used heater and air conditioning box for late 1967 and 1968 Mercury Cougar and Ford Mustangs. These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half...
Availability: Out of Stock
Item #: 11-0013 -
Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what...
Availability: Out of Stock
Item #: 17298 -
Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option. All of them were black in color. Later they were available in colors. We also have blue available, see our related tab. Replaces Ford part number C8AZ-18C490-B.
Availability: Out of Stock
Item #: 16788 -
Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option.Typically you only see black grilles. Later they were available in colors. We have this blue available. Replaces Ford part number C8AZ-18C490-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...
Availability: Out of Stock, On Order
Item #: 12-0082 -
This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.