AMK Products

New screw for attaching horn pads onto steering wheels 1968-69. 2 or 3 required, sold individually.

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.

Nut for attaching the power steering pump bracket onto the pivot stud coming out of the cylinder head. All 1967-69 Mercury Cougar and Ford Mustang engines additionally used on 1970 428CJ engines.

Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.

Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.

Bolts for securing the inspection cover for small block C-6 automatic transmissions 1971-73 Mercury Cougar or Ford Mustang. Not sure why 3 bolts, but one is different.

4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.

Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.

Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

3/8-16X1-1/8 Grade 5 flange bolt for attaching bucket seat tracks in any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, 4 needed for each seat. Replaces Ford part number 56340-S2.

Master clip kit which includes following fasteners: Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorns and regulatorPassenger side apron below relayRadio cable to dashKeep in mind that there are many other fasteners on 1968 Cougars / Mustangs that are not in this kit.

Master clip kit which includes the following fasteners:Engine bayEngine feedFirewallFront crossmemberParking lightsPassenger side apron below relayRadio cable to dashKeep in mind that not all fasteners found on 1967 Courgars / Mustangs are in this kit.

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Replaces Ford Part # 359747-S

Master clip kit which includes following fasteners:Door courtesy and speaker Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorn feedPassenger side apron below relayRadio cable to dashSide marker and headlightsTurn signal lights on hood scoopUnder dashVarious location zip tiesKeep in mind that there are many other fasteners on 1969 Cougars / Mustangs that are not in this kit. ...

Master clip kit which include the following fasteners:Door courtesy and speakerEngine feedFirewallFront crossmemberHorn feedParking light leadsPassenger side cowl brace and alternatorPassenger side shock towerRadio cable to dashSide marker lampsTaillight wiring to taillight body studsTurn signal lights on hood scoopUnder dashKeep in mind that not all fasteners found on 1970 Cougars / Mustangs are found in this kit. ...

Fits standard and XR7 Sold as a Kit as Pictured. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Correct Fit and finish for 1967, and works for 1968. Connects the overhead roof console to the mounting bracket. The only difference between the 67 and 68 kits are that the 67 screws are chrome and the 68 are zinc. The zinc will discolor over time, so we suggest using the 67 kit on a 68. Replaces Ford Part #: 519A58

Reproduction master exterior fastener kit for the Mercury Cougar Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Fender Splash Shields (front of fender) Fender Splash Shields (rear of fender) Battery Tray Hood and Hinges Cowl Panel Shock Tower Braces Hood Levelers Hood Latch and Catch Fender Extensions Quarter Panel Extensions Trunk Latch...

Reproduction body / exterior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Fender Splash Shields (front of fender) Fender Splash Shields (rear of fender) Battery Tray Hood and Hinges Cowl Panel Shock Tower Braces Cowl Braces Hood Latch and Catch Quarter Panel Extensions Trunk Latch...