AMK Products

Contains nut and washer. Fits all Ford alternators. AMK F-644.

4-Speed shifter rod hardware kit for 67 - 68 Cougars and Mustangs with a 4-speed transmission. Check out our video on rebuilding your shifter below: ...

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

3/8-16 X 7/8 9/16 AF .75 OD Sold individually. Fits all 390 & 428. Replaces Ford Part #: 374409-S.

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Reproduction bolts and washers for the manual transmission bell housing on any 67 - until 2/1968 Cougar or Mustang equipped with a 390 / 428.

Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.

Reproduction bolts and washers for the automatic transmission bell housing on any 1971 - 73 Cougar or Mustang equipped with a 351 engines and C-6 transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1971-73.

Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...

New hex head screw for attaching the fuel filler neck to the rear body. 67 to 70 Mercury Cougar and 1965-70 Ford Mustang. 1965-68 filler necks require 4 of this style screws. 1969-70 filler necks require a total of 5 hex head screws. #10 x 3/8". Replaces Ford number 42120-S8.

Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1970 Mercury Cougar and Ford Mustang with 302, 351W, 351C, 390, 428CJ engines. AMK number F-1496.

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1970 Mercury Cougar and Ford Mustang with 302, 351W, 351C engines. AMK number F-1497.

Fits Standard and XR7 Sold as a Set as Pictured.

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

14 piece bolt and screw set used to attach the convertible tack strip to the body. Kit comes with (12) 7/16 bolts and (2) phillips head screws. 

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.