AMK Products

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1970 Mercury Cougar and Ford Mustang with 302, 351W, 351C, 390, 428CJ engines. AMK number F-1496.

AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1970 Mercury Cougar and Ford Mustang with 302, 351W, 351C engines. AMK number F-1497.

Fits Standard and XR7 Sold as a Set as Pictured.

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

14 piece bolt and screw set used to attach the convertible tack strip to the body. Kit comes with (12) 7/16 bolts and (2) phillips head screws. 

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.

These reproduction J clips mount to the underside of the deck lid and fit Standard and XR7 trunk lids.

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

These reproduction hood latch support bolts fit both the Standard and XR7.

These reproduction hood latch catch bolts fit both the Standard and XR7.

Reproduction pair of 7/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

Reproduction pair of 1 1/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

These are our reproduction hood and hinge bolts and nuts for your Mercury Cougar or Ford Mustang.

Here are our reproduction hood latch support brace bolts and U nuts for the Mercury Cougar.

These reproduction fender to pillar bracket bolts fit both the Standard and XR7.

Here are our reproduction fender splash shield screws that fit 1967 Standard and XR7.

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

These reproduction quarter panel end seal screws fit both the Standard and XR7.

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.