All Products

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

This unique gasket is only slightly different from the driver side. The angle at the front is just a little different and notice it does not have a hole drilled for the remote mirror cable used on the driver side. This gasket was also used on the 1971 Ford Torino / Ranchero and Mercury Cyclone. This is an upgrade over the reproduction we carry for a 1969 - 1970 Cougar that has a passenger side Sport Mirror. The Ford Engineering number seen on the pad reads D1OB-17724-AA. Do you have questions...

Used wiring harness for the spark control box for the 1972 Mercury Cougar or Ford Mustang . This is only the harness, you can find the control box here.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

Tested, cleaned and working sequential turn signal motor for the VERY early 1967 Mercury Cougars. Some early units had 2 wires, some didn't. This is the single plug motor compared to the dual plug mid 1967 and 1968 turn signal motor. Clean used unit that is tested and will be functional. This unit will not be rusty or have internal water damage, may have minor repairs, no cut wires. Trouble shooting these systems takes time. A single bad ground at any portion of the turn signal circuit...

C9ZZ-18A318-B

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Grade A condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, passenger side only. Found on XR7 and most Standard model Cougars. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best...

Good clean, unrestored moulding with no dings or obvious scratches removed properly from the backside with a hammer and wooden block. Ford Master Part # C7WY-6551727-A. Here's a handy tip on removing the drip rail trim from your '67-'68. Click image to enlarge. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Used drip rail vinyl top retainer / moulding / trim with no holes for the Mercury Cougar.

Used drip rail vinyl top retainer / moulding / trim with rivet holes for the Mercury Cougar.

Ready for restoration or use it on your less than perfect driver. Not only will this moulding have a dull finish, but it will have scratches and dings as well. This is definitely an item ready for restoration.

Driver quality, no obvious dings or heavy scratches. New eyebrow attaching clips with nuts available here.    Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.

Ready for use on your less than perfect driver. Not only will this moulding have a dull finish, but it will have scratches and dings as well. This is definitely an item ready for restoration. 

Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This unit is sometimes called eyebrow moulding and is a decent part that will look great on a daily driver level car. If you need new attaching clips with nuts, you can get them here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Ford Part Number C9WY-16074-A ...

Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This unit is sometimes called eyebrow moulding and is a decent part that will look great on a daily driver level car. If you need new attaching clips with nuts, you can get them right here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

Chrome trim for the upper headlight housing. "L" shaped trim in Grade B used condition, very common to find in this condition. Fits 1971-72 Mercury Cougar only. Grade B trim will have limited pitting or minor road scars. Not quite show quality, but will be unbroken. Driver side upper trim.Replaces Ford part number D1WB-13B165-AA.

Chrome trim for the upper headlight housing. "L" shaped trim in Grade B used condition, very common to find in this condition. Fits 1973 Mercury Cougar only. Grade B trim will have limited pitting or minor road scars. Not quite show quality, but will be unbroken. Driver side upper trim. Replaces Ford part # D3WB-13B165-AB.

Chrome trim for the upper headlight housing. "L" shaped trim in Grade B used condition, very common to find in this condition. Fits 1973 Mercury Cougar only. Grade B trim will have limited pitting or minor road scars. Not quite show quality, but will be unbroken. Passenger side upper trim.Replaces Ford part number D3WB-13B164-AB.

Reproduction moulding for 'upper windshield garnish' for any 1970 Mercury Cougar or 1969-70 Ford Mustang. This item not for 1969 Cougar hardtops or for convertibles. Item comes in black as shown, paint to match non-black interiors. This is a made in Taiwan part, and we recommend our used header mouldings. Ford part # C9ZZ-6503606-A.

Used moulding for 'upper windshield garnish' for any 1969 Mercury Cougar. This item not for convertibles. Item comes in black as shown, paint to match non-black interiors. Ford part # C9WY-6503606-A.

Anodized aluminum snap on moulding for the rear edge of the hoods on early 1971 Mercury Cougar XR7 coupe and XR7 convertible models. Same moulding available optionally on 1971 Mustangs too. Available only up until 2-1-1971. Made from anodized aluminum, subject to very minor nicks and scratches from prior use, will still have a shine to it, good for driver quality use. Sold on an exchange basis only, must have core sent to us prior to us sending this piece out. Also available restored, but only...

Core driver side (left hand) hood lip moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16855-A.

Used driver side (left hand) hood lip moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches or corrosion. Perfect for your daily driver that is in above average condition.  If you return a good core we can give you a substantial credit towards this part.Ford part # C7WY-16855-A.*NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in...

Core passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. Good used core with minor dings, scratches, and dullness.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

Used passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. Good used driver quality trim with no obvious dings, deep scratches, or corrosion. Perfect for your daily driver that is in above average condition. If you send in a good core we can give you a discount on this part.Ford part # C7WY-16856-A.*NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit...

Used interior quarter window moulding for the driver side (left hand) of the Mercury Cougar coupe. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529035-A.

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529034-A.

Core aluminum rear deck lid moulding / trim for the Mercury Cougar. Good core ready for restoration. No kinks, flattened areas of heavy pitting. Seven clips are used to install the deck lid moulding and we have new clips available here. Ford part # C7WY-6542512-A. *NOTE* Keep in mind we buy most trim and mouldings found on a Cougar. For more insight on this tricky trunk trim, check out our video below: ...

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Used passenger side (right hand) lower rear window moulding / trim for your Mercury Cougar. This is the same part for 1969-70 as well, however those pieces carry a part number starting in C9WY.Ford part # C7WY-42404-A. *NOTE* This unit carries a $50 refundable core charge. If you are unable to return your core within 30 days after the initial purchase, your refund will be in store credit only. If you have an unacceptable core, we have a core option for you in this moulding / trim section....

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. You can use this 3M product to glue this trim to the glass. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call 503-463-1130...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. Used trim will have minor wear, weathering, and generally be free of defects. This is a trim exchange, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...

Core lower windshield moulding / trim for your Mercury Cougar or Ford Mustang. Suitable for restoration or could fit right in on your lower quality daily driver. Ford part # C5ZZ-6503148-B.

NOTE: This listing is for a pair of blemished mouldings, please see the above photos for examples of blemmed pieces. This is the right hand and left hand 1/4 panel moulding. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number...

NOTE: Some modification required to fit Cougars! These are actually 1971-73 Mustang wheel lip mouldings, which have a much different shape / contour than Cougar and will need minor modifications to make fit. That being said, they are the closest alternative we have found that can be made to fit and look reasonably good for much less than restored originals or NOS. This set is what we refer to as the "Better than nothing" option. No complaining or whining please... Check out our video below,...

This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar. These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore" mouldings that are available as they...

This is a core five piece set of front windshield mouldings for a 1969 - 1970 Mercury Cougar. These trim parts need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard trim parts of that description. We do not recommend the reproduction, offshore mouldings that are available as they...

Factory spare tire hold down bolt for 1969-70 Mercury Cougar convertibles with style steel wheels. Note the felt and jack placement. Overall length 12-1/4 inches. As always, the threads are 1/2"-13.