All Available Parts - 1972 Ford Mustang

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

Made from clear acrylic plastic with prisms added to increase the bulb brightness.Ford originally used white nylon with no prisms, which makes the light very dull. Replaces Ford Part # D1AZ-13783-B.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Grade B used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and...

Used RIGHT side bucket seat medium brown / ginger hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634. ...

Used RIGHT side bucket seat maroon hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat dark green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat light green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat white hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used RIGHT side bucket seat dark blue hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used LEFT side bucket seat medium brown / ginger hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635. ...

Used LEFT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat dark green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat light green hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat white hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used LEFT side bucket seat dark blue hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Not an exact replacement, but a decent replacement if you have a rear view mirror that the silver is peeling on. Includes new glue on mounting tab (bracket). Replaces Ford Part #: C8AZ-17700-A. This picture below shows the rear view mirror variations from 1967-1973. Check out this video ...

This special bracket gets glued to the windshield glass. Rear view mirror mounts on it. Plain finish. Replaces Ford Part #: C9AZ-17698-A.

These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until the glass...

Core driver side (left hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The...

Sold as a pair

Replaces Ford part #D1ZZ-6561692. Sold as a pair, available in black only. They can be painted but it is rather difficult to get paint to adhere long term. We have most colors available used, contact us for availability.

American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process.NOTE: These foam kits work well on the Standard and Decor interiors but you will find on the XR7 the lower portion does not work well.

Very nice reproduction knobs for 1971-73 Mercury Cougar and Ford Mustang with outboard mounted seat back releases. Also fits 1971 and newer Mercury Comet and Ford Maverick with bucket seats, as well as 1971 and newer Pinto. *Note - Not to be confused with the center mounted release knobs.

Core passenger side (right hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The price...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1972-73 cars due to the seat belt location in the side panels. 1971 seats are a bit wider.Replaces Ford part number D2ZB-6563120.*Note - Excludes 1971 Mustang and Cougar.

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang coupe or hard top. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-6566700.*Note - Does not fit convertible.

Used RIGHT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561634.

Used LEFT side bucket seat black hinge cover, for any 1971-73 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections, common colors in shock include: ginger, green, and white. Others available in limited quantities. These do not accept paint very well, Reproduction pairs of these seat covers are available in black only, see related item list. Ford number D1ZB-6561635.

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

Reproduction vinyl top moulding clip for all factory installed 1971-73 Mercury Cougars and should also work on the 1971-73 Ford Mustangs. These are like the ones that attach under the nail heads. Typically, the vinyl top mouldings for the 1971-73 are aluminum.  These are actually Au-Ve-Co brand part number 11288 which is a replica of a GM part, but these are the closest to the originals as we can find. Even though these are not exact copies of the originals, in our tests...

Inner tie rod end for 1971 - 1973 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D1ZZ-3A131-A

Outer tie rod end for 1970 – 1973 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Includes 1969 Boss 302 Eliminator and Mustang, and 1970-74 Ford Maverick and Mercury Comet. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: D0OZ-3A130-B.

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

This is the manual steering gear box for 1972 1973 Mercury Cougars. Marked SMA-T and is 24:1 ratio. It is pretty rare to find a Cougar optioned without power steering. According to Kevin Marti's COUGAR...by the Numbers book 99% of all 1971 - 1973 Cougars came with power steering from the factory. If you have a non-power steering Cougar for these years you are in the 1% club. The current used steering box has a date of 1H06B, August 6, 1971. For an early 1972 Cougar or Mustang. Used...

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

1971 - 1973 Ford power steering pump dipstick. Used starting 2-8-1971.

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

D1ZA-3B153-BA 1971 - 1973 Power steering pitman arm. May also have casting number D3ZA-3B153-BB. Ford part number D1ZZ-3590-B.

Sold individually # 377112-S

Remanufactured constant ratio power steering box for the Mercury Cougar or Ford Mustang equipped with factory power steering. These units are Saginaw 800 Series torsional power steering gear boxes that feature 4 turns lock to lock. In our experiences this box design is very durable and not prone to wear like the early style dry steering boxes. These units are tagged as SPA-S, SPA-U, SPA-AC, SPA-AE.. *NOTE* This unit will work in any 1971-73 Mercury Cougar or Ford Mustang except for those...

This is the 'variable ratio' power steering box, Saginaw manufactured. The Variable Ratio steering box was part of the Competition Suspension Package available optionally on all Cougars or part of the GT or 351CJ Performance Group.This Variable Ratio steering box should have come standard with all 1971 - 1973 M or Q code 351-4V or C or J code 429-CJ equipped Cougars. Sometimes this tag number could also be SPA-T, SPA-V, SPA-AD, SPA-AF,

This reproduction pitman arm equipped on 71 - 73 Cougars and Mustangs with factory power steering. Heavy-duty cast construction. Includes a new castle nut, cotter pin and zerk fitting. Replaces Ford part number D1ZZ-3590-B.

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Check out this video ...

You can use 1968 up to 1973 lower control arms on a 1967 only if you change the strut rod to the 1968 - 1970 style. We have the strut rods available in both new and used form. Replaces Ford part #: C8OZ-3078-A. Sold individually, right is the same as left. *NOTE* The Cougar only, 1967 only, lower control arm is not available in reproduction form but you can rebuild the originals so do not throw away your cores as they may prove to be valuable one day. Mustang never used the articulated strut...

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Check out this video

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

Complete kit with shaft for one side. Includes grease seals and zerk fittings. Note! Often times the fine threads in the upper control arms will be worn to the point of being stripped. To keep this kit properly in place you may have to tack weld the threaded caps to the control arms in a couple of places.

380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.

Steering drag link for all power steering and non-power steering Cougars and Mustangs from 1971 - 1973.Replaces Ford part number D3ZZ-3304-A .

NOTE: THIS IS A NEW DESIGN AND WILL NOT LOOK EXACTLY LIKE YOUR ORIGINAL, BUT IT WILL IN FACT FIT YOUR 71-73 COUGAR OR MUSTANGIdler Arm Assembly for 1971-1973 Cougar and Mustang. Fits all 1971-1973 Cougars and Mustangs with manual or power steering. Complete with bushings installed and ready to bolt on. Does not include Zerk fitting. This Idler arm helps stop that floating feeling going down the road. Please see the installation photos below. Easy to install.  ...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

This is the manual steering gear box for 1971 Mercury Cougars. Marked SMA-R and is 22:1 ratio. It is pretty rare to find a Cougar optioned without power steering. According to Kevin Marti's COUGAR...by the Numbers book 99% of all 1971 - 1973 Cougars came with power steering from the factory. If you have a non-power steering Cougar for these years you are in the 1% club.  1972-73 manual Steering boxes had a ratio of 24:1, and were tagged SMA-R.  We offer used boxes because...

This is the 'constant ratio' power steering box, Saginaw manufactured. Tag number SPA-S, and sometimes could also be SPA-U. This is the standard power steering box for all Cougars 1971 1972 1973. We offer used boxes because in our experiences this box design is very durable and not prone to wear like the early style dry steering boxes.

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

This is an economy version of the lower control arm assembly, with a spot welded on "heavy duty" reinforcing plate. Yes, this is the same "heavy duty reinforced" lower control arm assembly carried by the other parts vendors. We are sorry, but we just cannot recommend this part. The Scott Drake premium version (Part #:26709) of this lower control arm is far superior and basically the same costs. In the picture, you can tell that it is lacking a rolled lip on the outer edge that...

Used shock tower cap for the 1971-73 Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Ford part # D1ZZ-18A017-A.

Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.

Used, chromed shock tower cap for the 1971-73 Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. We offer chromed versions of the shock tower caps for those that want to add some bling to the engine compartment.Ford part # D1ZZ-18A017-A.

Rebuildable Core grade lower control arm for any 1971-73 Mercury Cougar and Ford Mustang. These are wearable items, and we list this item for those folks who really wish to go 'Concours trailered'. These interchange from side to side, two per car. Fits other 1971-73 Ford cars such as Torino and Cyclone. No jacking tabs found on this version from Ford. Even though these are select parts, we recommend that the ball joints and bushings be replaced.  Anghel Restorations can...

Reproduction passenger side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69.  Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

After being obsolete for years we have brought back another hard to find clutch equalizer component for 1971-3 Mustang and Cougar. Numerous other Ford application too. Replaces Ford part # C5AZ-7B545-A

Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

Manual transmission clutch bolt kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions any engines. Quality AMK bolt kit F-3263.

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.

Top Loader transmission input shaft seal, small shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.*Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Top Loader transmission rear seal, 28 splined shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. *Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has the elongated hex socket portion. There is also a version that has a rounded upper section formed on the socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A...

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard! Only the 71-73 came with the speckled pattern.

Spare Tire Mount Wing Nut Reproduction for the 1968 through 1973 Mercury Cougar / Ford Mustang

For 1968 Ford standardized or changed all of the J-bolt threads to the beefier 1/2"-13. We have noted two variations of this wing nut. The most obvious identifier between the two is the tabs in the center. The majority have these tabs present, the minority do not. We also stock and carry the correct disc or hold down plate, and the J bolt. Lots of sizes and lengths for those. Do you have the correct one?

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

According to the MPC 1970 primarily, a few 1971-1973's. If you have a hardtop or coupe, (VIN numbers starting with either 0F91 or 0F93) and standard wheels with hub caps. Or, any 1971 - 1973 with style steel wheels. Total length is 6-1/4 inches, with 4 inches being threaded. Threads 1/2-13. We find this bolt to only have 2 1/2" of threads. More data is needed as the MPC is not reliable on these items. What do you have in your trunk? We want to know! Search words 70 71 72 73 1972

1971 - 1973 Mercury Cougar hard tops and coupes with regular steel wheels and hub caps. J bolt total length listed in MPC is 8-3/4 inches, with 6-1/2 inches threaded on the straight end but we find the actual length to be 10" long with about 4" of threads. We also see this used with the 1971 - 1973 Kelsey Hayes Styled Steel wheel even though the MPC lists another size. There are absolutley to absolutes when it comes to items like these and what Ford "may" have called for. Would love to hear...

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has a rounded upper section of the hex lug socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A (Factory Service Replacement since 1974) If you'd like a particular...

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Replaces Ford Part # C7AZ-6243505-B Click on images to enlarge.

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73. AMK F-227 Check out this video