All Available Parts - 1970 Ford Mustang

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Ford casting number D0ZA-7E046-E. Adapter plate for mounting the factory installed Hurst 4 speed shifter control assembly to the Top Loader transmission. Mercury Cougar Ford Mustang 351 and Boss 302 engines. Ford master part number D0ZZ-7E046-B.

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

D0ZZ-7519-A Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...

Grade A used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This is a real clean rust free cover but if you are wanting to save money, we have grade B's which will have a dent or creases for about half the price. Find the grade B here.Ford part number C3AZ-6366-A. ...

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Original dipstick tube. Application 1970 - 1972 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. These have a little longer tab than the 1969 FMX dipstick tube.Ford master part number D0OZ-7A228-C.

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Used dipstick tube for the Mercury Cougar or Ford Mustang equipped with the C6 transmission. The C6 option can be identified by code "U" on your door data plate. Ford part # D0ZZ-7A228-A.

Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 15-1/2 inches long. The C-6, automatic transmission, was used only on 1970 Cougars with 428 Cobra Jet engines. Transmission code "U" on your door data tag. Ford part number D0ZZ-7E330-D. *Trivia - The 4V Cleveland engines were not available with the heavier...

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some dents and or scrapes. These were not painted originally, may have light rust that will clean up. Consider them Grade B used.

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.

This is a good used speedometer cable from a 1969 - 1970 Mercury Cougar with a FMX transmission. The cable housing has no burns and the fragile plastic squeeze clip that fastens it to the back of the speedometer is not broken. Keep in mind that some 1970 models use a two part cable. This cable will work in place of the two part cable seen on some 1970 cars. This cable measures 58 1/2" at its very most outer ends.

This very rare part is unique to the 1970 - 1971 CJ and SCJ C6. There was no 390 option in 1970 - 71. Sales were down on the CJ equipped Cougars in 70-71 making this one very hard part to obtain.  We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D0ZP-D. Ford Part #: D0ZZ-7A256-D. Check out our video on rebuilding your shifter below: ...

This rod is unique to 1970 because it was the first year of the lock out rod. Very hard to come by when you consider there was no 390 option for 1970. Notice this rod features two different part numbers. Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. 428 Cobra Jet engines were the only Cougar engines to receive the C-6 automatic transmission. Shift rod approximately 17-1/2 inches long....

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

This reproduction rod is made from stainless steel and weighs slightly more than the original.

This one year only rod is correct for the 351 Cleveland 4V and is approximately 27". This rod originally had a light blue paint daub near the carburetor. It is a little longer than the 2V rod and connects to the carburetor at a slightly higher point.

This rod is correct for the 428 CJ / SCJ with a C6 and is approximately 28".

Unique to the 1970 351w with FMX. Originally came with a light blue paint daub at the top.

Good used original power steering lower hose bracket and retainer with a new reproduction insulator installed in place of the original crusty or missing insulator.This bracket is for cars with the big block routed power steering hoses.

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct length of power steering hoses.

NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.

Tag marked HBA-BR for use on 1970 Cougar and Mustang with power steering pumps originally installed on 428 Cobra Jet engines only. Could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. *Note - 1970 428CJ only.

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

This item will have a refundable core charge added to your order. One year only, power steering pump. When fully assembled you will notice that this year P/S pump has an offset fitting for the pressure hose on the back of the reservoir. 1970 Mercury Cougar and Ford Mustang with 351W or 351C, and Boss 302 engines. *Note - Your power steering pulley has to be removed and reinstalled on these pumps.

The horn switch is embedded in this soft part. Limited colors on hand, call for availability. White plastic is prone to cracking due to shrinkage and age. Most will have a crack or two. Ford part number is D0ZZ-13915-A

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

This restored three spoke, rim blow steering wheel was used on all Cougars 1970-73 except the Cougars equipped with standard interior or on rare occasion the 1973 Cougars that came with the rare 2 spoke leather wrapped wheel. The Cougars equipped with standard interior used a two spoke wheel with the horn button located in the center pad. If you choose to send in a core for exchange it will need to be a clean one as we will not restore steering wheels that have huge cracks, severe UV damage or...

These are cracked core wheels as taken from a parts car. The Center pad is not included and you can count on the rubber switch being rock hard. This wheel is for restoration purposes and we cannot guarantee that we will have all colors in stock at all times. The three wheels shown here are random examples and are not what you will actually be getting when you order. Most colors in stock, call for color, or leave desired color in the comments section of your order. ...

Carburetor gasket for all 1970-71 Mercury Cougar and Ford Mustang with 351C-4V engines. This is a new gasket meant for use with stock Ford intake manifolds and correct Autolite/Motorcraft 4300 carburetors. Single gasket as shown with correct metal sandwich, if you have a carburetor spacer plate you would need two gaskets.

Larger sized retainer that screws to upper front lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these sometimes installed in the front position at the top of the interior quarter panel next to the window glass, mostly the front position is empty or the factory installed two of the smaller retainers. This retainer helps the top section of the soft trim panels from rattling. The...

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

NOS glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Reproduction glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Used under dash ashtray assembly for non-console 1970 Mercury Cougar and Ford Mustang. Pebble grain finish that you paint to match your interior color. Comes as shown with light.

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

New Old Stock NOS fuel sending unit for Standard Model 1970 Mercury Cougar or Ford Mustang, all without low fuel indicator. New in the box Fuel Sender with part numbers D0WF-9275-A and D0WY-9275-A. Yes, sometimes there is a Cougar part on a Mustang. Single pin connector, not for use with XR7 models.Check out the video below on our new gauge tester: ...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1970 Mercury Standard model Cougars and all Ford Mustangs with 20 or 22 gallon fuel tanks. This is an original 1970 fuel sending unit with one electrical prong. Ford casting number D0WF-9275-A. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3 prongs...

These stainless steel tubes are made to exact O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip.

CARBURETOR SPACER PLATE, 0.28" thick, has straight 1/2" PCV hose nipple in rear. Very hard part to find in orginal form.Ford Part Number DOOZ-9A589-A

1970 302-4V Boss Eliminator Holley 4150 carburetor, 4 speed manual transmission - all 50 states. DOZF-9510-Z stamped on the carburetor air horn. Holley list #4653, 780 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. Manual choke.

1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-T stamped on the carburetor air horn. Holley list #4515, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. *Excludes Super Cobra Jet.

1970 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. D0ZF-9510-AC stamped on the carburetor air horn. Holley list #4516, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. *Excludes Super Cobra Jet.

1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-AB stamped on the carburetor air horn. Holley list #4514, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Without air conditioning. *Includes Super Cobra Jet.

1970 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. D0ZF-9510-G stamped on the carburetor air horn. Holley list #4513, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. Without air conditioning. *Includes Super Cobra Jet.

1970 351-2V Autolite 2100 carburetor, 3 or 4 speed manual transmission - All 50 states. D0AF-E stamped on the carburetor base, 1.21" venturi size and 351 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1970 351-2V Autolite 2100 carburetor, automatic FMX transmission - All 50 states. D0AF-V stamped on the carburetor base, 1.21" venturi size and 351 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *With air conditioning.

1970 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. D0OF-Z stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *With or without factory air conditioning. That is what the Master Parts book says.

1970 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. D0OF-AB stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *With or without factory air conditioning. That is what the Master Parts book says.

1970 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. D0OF-C stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *Without air conditioning.

1970 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. D0OF-AA stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. Other acceptable numbers are D0OF-9510-AD, and D0OF-9510-H.*With air conditioning.

1970 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. D0OF-AD stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning.

1970 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. D0OF-G stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *With factory air conditioning

1970 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. D0OF-D stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *With or without factory air conditioning. That is what the Master Parts book says.

1970 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. D0OF-Y stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *Without air conditioning.

1970 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. D0OF-AC stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *Without air conditioning.

1970 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. D0OF-H stamped on the carburetor base, 1.25" venturi size and 605 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning.

1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-H stamped on the carburetor air horn. Holley list #4514, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Without air conditioning. *Includes Super Cobra Jet.

1970 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. D0ZF-9510-AA stamped on the carburetor air horn. Holley list #4513, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. Without air conditioning. *Includes Super Cobra Jet.

1970 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. D0ZF-9510-U stamped on the carburetor air horn. Holley list #4516, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. *Excludes Super Cobra Jet.

Original Boss 302 carburetor spacer plate, bake-o-lite with metal tube angled to the side. See the link on the Boss 302 website here.Replaces Ford part number C9ZZ-9A589-C.

These steel tubes made to exact O.E.M. standards and specifications.

D0AE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D0AE-9431-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C9OE-9430-D and left C8OE-9431-B side matching exhaust manifolds. *Trivia: All 1970 428CJ's had Q engine codes. Ram air was optional and many had that option. Not sure? only way to tell for sure is with a report from Kevin Marti.

C9OE-9430-D 428 Cobra Jet factory original cast iron exhaust manifold for passenger side. *No spacer required.

C9OE-9430-B 351W factory original cast iron exhaust manifold for passenger side. For all 1969 and 1970 Windsor 351's. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay...

C9ZE-9431-A Factory original cast iron exhaust manifold for driver side. Correct for all Boss 302 Eliminators 1969 and 1970.

C9ZE-9428-A Factory original cast iron exhaust manifold for passenger side. Correct for all Boss 302 Eliminators 1969 and 1970. Nice piece from a CA car, no damage or pitting.

C8OE-9431-B 428 Cobra Jet factory original cast iron exhaust manifold for driver side. For all 1969-1970 428CJ Cougars after 9/2/1968 build date.

D0AE-9431-A 351-2V Cleveland, factory original cast iron exhaust manifold for driver side. At some point there may have been a D0AE-9431-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some after-market aluminum intakes such as one offered by Edelbrock.

D0AE-9430-A 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum intakes such as one offered by Edelbrock.

351 Windsor factory cast iron exhaust manifold set, both a correct right C9OE-9430-B and left C9OE-9431-B side matching exhaust manifolds. Same manifolds used on all 351 Windsor engines in 1969 and 1970.  No extra charge to look for a date coded pair but no promise we can hit it spot on either.  

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. Replaces Ford Part #: D0ZZ-8592-A.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. NOTE: Dwayne from "The Brothers Car Collection" clued us in to the fact that the choke tube fitting on the passenger side is indexed 180 degrees off on some sets we sell. Fortunately you can carefully spin it around with vise grips so the opening faces...

Reproduction 428 Cobra Jet Exhaust Manifold Spacer 1968 - 1970 Mercury Cougar, Ford Mustang, Shelby and Torino Repro

Dated 9M6, December 6 1969. Boss 302 or 351C Ford water pump core, suitable for rebuilding. This version has a casting number of D0OE-D. Found on many Ford 351 Cleveland engines from 1970. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.