All Available Parts - 1970 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 2701-2800 of 3357
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 12223 -
Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...
Availability: Out of Stock
Item #: 17-0010 -
These four original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never...
Availability: Out of Stock
Item #: 31671 -
This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.
Availability: Out of Stock, On Order
Item #: 26151 -
This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...
Availability: Out of Stock
Item #: 23563 -
This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.
Availability: Out of Stock, On Order
Item #: 27372 -
Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.
Availability: Out of Stock, On Order
Item #: 27371 -
Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.
Availability: Out of Stock
Item #: 11-0504 -
Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70.
Availability: Out of Stock
Item #: 11-0505 -
Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70.
Availability: Out of Stock
Item #: 13-0009 -
This is a used fuel door insert we have cleaned up, painted the background black and installed a 1967-1969 headlight door walking cat emblem on. The original 1970 ELIMINATOR piece that this resembles had a smaller sized cat so this is not exactly correct for your original 1970 Eliminator.
Availability: Out of Stock
Item #: 24565 -
For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.
Availability: Out of Stock
Item #: 24560 -
For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.
Availability: Out of Stock
Item #: 32149 -
Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...
Availability: Out of Stock
Item #: 25248 -
Cable length 22.83 inches long, identified by a plastic ball shaped end attached onto the pedal side of the cable. Must be used with a 1970 accelerator pedal shaft. This is an unbroken part. Notice there are two versions, one has plastic covering the cable and the other has an exposed cable.
Availability: Out of Stock
Item #: 41359 -
Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.
Availability: Out of Stock
Item #: 18965 -
351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...
Availability: Out of Stock, On Order
Item #: 11336 -
New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.
Availability: Out of Stock
Item #: 41047 -
Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.
Availability: Out of Stock
Item #: 14250 -
Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.
Availability: Out of Stock
Item #: 20192 -
This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
Availability: Out of Stock
Item #: 30642 -
Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.
Availability: Out of Stock
Item #: 24795 -
C9ZE-6583 Cast aluminum valve cover. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. Sometimes called 1969 Shelby valve covers. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of "Snake" finned aluminum valve covers.
Availability: Out of Stock
Item #: 20129 -
SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.
Availability: Out of Stock
Item #: 24796 -
C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...
Availability: Out of Stock
Item #: 31973 -
Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...
Availability: Out of Stock
Item #: 41132 -
Replaces Ford Part # C8AZ-2B164-A
Sold individually
Availability: Out of Stock
Item #: 23780 -
Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.
Availability: Out of Stock
Item #: 26132 -
Used seat belt bolt washer for the Mercury or Ford.
Availability: Out of Stock
Item #: 27359 -
Chromed engine oil dipstick as found on all 1970 Mercury Cougar and Ford Mustang with 428CJ engines (Q or R Code). Top of shield to dip stick is 20 inches. The handles were chromed originally. Ford part # D0OZ-6750-C, Ford casting # D0OE-6750-C.*NOTE* This is an improved dipstick that better reflects the actual full mark, from previous 428CJ dipsticks.
Availability: Out of Stock
Item #: 27362 -
Chromed engine oil dipstick as found on all 1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # D0ZZ-6750-B, Ford casting # D0ZE-6750-C.
Availability: Out of Stock, On Order
Item #: 31577 -
Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.
Availability: Out of Stock
Item #: 11270 -
Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.
Availability: Out of Stock
Item #: 33551 -
Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A
Availability: Out of Stock, On Order
Item #: 11788 -
Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.
Availability: Out of Stock, On Order
Item #: 26023 -
Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.
Availability: Out of Stock
Item #: 15381 -
Rubber oil pan gasket for the 351 Cleveland engine in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.
Availability: Out of Stock
Item #: 33552 -
Used oil screen pick up tube assembly from a FE or big block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...
Availability: Out of Stock
Item #: 11360 -
Availability: Out of Stock
Item #: 33511 -
Used front console support bracket. Held in place by 2 phillips screws at the front, under the console. NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.
Availability: Out of Stock
Item #: 31574 -
Used middle console support bracket. Held in place by 2 rivets midway under the console.
Availability: Out of Stock, On Order
Item #: 20252 -
A nice reproduction oil pan in Chrome finish for the 351C. Replaces Ford Part #: D0ZZ-6675.
Availability: Out of Stock
Item #: 42048 -
The oil filter made by the original Ford supplier.
Availability: Out of Stock
Item #: 15281 -
This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.
Availability: Out of Stock
Item #: 30880 -
This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...
Availability: Out of Stock
Item #: 30512 -
Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.
Availability: Out of Stock
Item #: 30540 -
Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...
Availability: Out of Stock
Item #: 31393 -
Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.
Availability: Out of Stock
Item #: 314047 -
Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.
Availability: Out of Stock
Item #: 25237 -
D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.
Availability: Out of Stock
Item #: 25238 -
D0ZZ-7528-D Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. See the 1969 listing if you have a 1970 351 Windsor engine. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...
Availability: Out of Stock
Item #: 25239 -
D0ZZ-7528-E Equalizer bar or "Z" bar for Boss 302 Eliminators 4 speed transmissions only. This is a used part and it will most likely show some wear form previous use.
Availability: Out of Stock
Item #: 24869 -
C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.
Availability: Out of Stock, On Order
Item #: 26079 -
Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302
Availability: Out of Stock
Item #: 33067 -
Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...
Availability: Out of Stock
Item #: 24625 -
Application, 1969 - 1970 390IP / 428CJ & 428SCJ engines without air conditioning. Casting number 80B. 5-1/2" diameter and 7/16" sheave width.
Availability: Out of Stock
Item #: 41856 -
Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.
Availability: Out of Stock, On Order
Item #: 41567 -
Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A
Availability: Out of Stock
Item #: 42303 -
This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. Includes both Pressure and Return hose that connect to the control valve. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against...
Availability: Out of Stock
Item #: 11648 -
[No Description Provided]
Availability: Out of Stock
Item #: 11650 -
Premium power steering hose kit for the 1970 Cougar or Mustang with a small block.
Availability: Out of Stock
Item #: 11647 -
We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang with or without Power Steering Cooler. Be sure to select the option to...
Availability: Out of Stock
Item #: 42029 -
This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.
Availability: Out of Stock, On Order
Item #: 31010 -
Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.
Availability: Out of Stock
Item #: 24596 -
Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...
Availability: Out of Stock
Item #: 15404 -
We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...
Availability: Out of Stock
Item #: 24441 -
C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...
Availability: Out of Stock
Item #: 14972 -
Replaces Ford Part # D0WY-14305-C & D0WY-14305-A
Availability: Out of Stock
Item #: 11-0324 -
Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.
Availability: Out of Stock
Item #: 25180 -
D0ZE-6312-B Application is 1970 Boss 302 Eliminator with or without power steering. Triple sheave pulley 5-15/16" and dual outer 6-11/16" diameter. Ford Master Part number D0ZZ-6A312-A. Also a four bolt mount to the crankshaft balancer.
The reason for a triple sheave pulley on Boss 302 engines is the inclusion of the Thermactor Smog system from the factory. Smog pumps were placed so that they worked off of the outermost pulley groove on a 3 sheave crankshaft pulley. If with power steering the...
Availability: Out of Stock
Item #: 24994 -
Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.
Availability: Used / Wrecking Yard Item
Item #: 24381 -
Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.
Availability: Out of Stock
Item #: 24337 -
Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.
Availability: Out of Stock
Item #: 24451 -
Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.
Availability: Out of Stock
Item #: 24567 -
C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.
Availability: Out of Stock
Item #: 12347 -
Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...
Availability: Out of Stock
Item #: 12344 -
Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.
Availability: Out of Stock
Item #: 41441 -
This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.
Availability: Out of Stock
Item #: 11-0453 -
Grade B used A/C center vent for any 1969-70 Ford Mustang. This will some limited chrome pitting in the plating. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.
Availability: Out of Stock
Item #: 11846 -
These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....
Availability: Out of Stock
Item #: 41931 -
There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...
Availability: Out of Stock
Item #: 11-0069 -
Used fresh air vent found in the driver side kick panel of all 1969-70 Mercury Cougar and Ford Mustang with or without air conditioning. Please also see the listing for new gaskets for installation.Replaces Ford part number C9ZZ-6501935-A.
Availability: Out of Stock
Item #: 24828 -
Here is our NOS vacuum valve assembly which is fairly hard to come by these days. This unit is for Mercury Cougars or Ford Mustangs with integral or factory air conditioning. This part is good until an assembly date of 1/3/1972 and, if you want, we also have good used pieces in stock for your Coug or Stang as well. Ford part # C9ZZ-19B888-A.
Availability: Out of Stock
Item #: 11-0418 -
Grade A used A/C center vent for any 1969-70 Ford Mustang. This will have almost perfect chrome plating, minor blemishes only, no pitting. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.
Availability: Out of Stock
Item #: 11-0432 -
Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.
Availability: Out of Stock
Item #: 20557 -
Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.
Availability: Used / Wrecking Yard Item
Item #: 15158 -
Cast iron pedestal mount for the air conditioning compressor on all 1970 Mercury Cougars and Ford Mustangs with the 351W H code 2V engine. Ford also used this bracket on other 1970-71 Ford passenger cars with 351W engines only.Ford casting number D0AA-2882-E.
Availability: Out of Stock
Item #: 24824 -
According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...
Availability: Out of Stock
Item #: 24522 -
Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...
Availability: Out of Stock
Item #: 25069 -
Used 14x7" stock stamped steel wheel for the Mercury Cougar and Ford Mustang / Torino. Rare seldom seen size most commonly found on a Ford Torino. These were offered from 1971 through 1973 on the Cougar and 1970 - 1973 on the Mustang and Torino. Have a bent or damaged wheel? Don't have a spare? Total width is 8" with a 4" backspacing. Various conditions and subject to availability. Used 'as is', wheel as found in the wild.Ford part # D0OZ-1007-B.
Availability: Out of Stock
Item #: 30521 -
Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....
Availability: Out of Stock
Item #: 18940 -
Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...
Availability: Out of Stock
Item #: 18943 -
These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.
NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...
Availability: Out of Stock
Item #: 30258 -
Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 16-0040 -
Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 15-1/2 inches long. The 4 speed manual transmission, could be ordered on any 1970 Cougar or Mustang regardless of engine (except Boss 429). Transmission code "5" or "6" on your door data tag. Ford part number D0ZZ-7E330-C....
Availability: Out of Stock
Item #: 25165 -
Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 15-1/2 inches long.
The 4 speed manual transmission, could be ordered on any 1970 Cougar or Mustang regardless of engine. Transmission code "5" or "6" on your door data tag. Ford part number D0ZZ-7E330-S.
*Trivia - Starting in...
Availability: Out of Stock
Item #: 10956 -
D0ZA-7E046-D Adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission on a 1970 big block 428 cobra jet Cougar or Mustang. Ford master part number D0ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 25206 -
Backup lamp switch that mounts to the factory 3 speed shifter linkage. 69 70 71 72 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-947. Used up until 5-15-1972. Tested and working switch with wiring and plug.*Note - 3 speed switches are different than the manual 4 speed switches.
Availability: Out of Stock
Item #: 25205 -
D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.
Availability: Out of Stock
Item #: 25207 -
D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.
Availability: Out of Stock
Item #: 31672 -
New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.