All Available Parts - 1970 Ford Mustang

Tested and working used pair of Hi and Lo tone horns. 1969-70 Mercury Cougar and Ford Mustang used part number C9ZF-13802-C and C9ZF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

Used brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.

If you look close at our used set I do not think you could tell the difference, look at the back side in comparison to used and you will see a noticeable difference. *NOTE* The fifth part slips into the backside of the inner knob on the passenger side and acts as a spacer for Cougars or Mustangs without the rear fader option. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. ...

Nice clean set of four used radio knobs for your 69-70 Mustang or Cougar. No peeling or cracks. The inset picture shows the used next to the new from the backside. The reproductions are shown on the right. Whereas the repros are nice, the originals are still superior. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and 68-70 AM-FM radios. White plastic reproduction spacers available here. The white...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny...

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Good used part without excessive rust or damaged rubber. For use with fixed column only.

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Floor mounting column bracket for the 69-70 Cougar or Mustang. Rubber gasket may not come with bracket, and if it does will most likely need replacing. Undamaged with original fasteners. Get the gasket here.Ford part number C9ZZ-65017A50-A.

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.

Used upper and lower inner steering column shafts for a fixed steering column on the 1970 Cougar or Mustang. Bushings will be intact and in good shape.

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

Inner steering column shaft for a fixed steering column on the 1970 Cougar or Mustang.

Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Correct nut that is designed not to come undone.

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 8-32 thread. Ford part # D0AZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Tilt release lever or bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth. These units will be mint with no broken or chipped teeth....

Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part # D1AZ-3D651-A, casting number D1AA-3D651-AA or D0AA-3508-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the tilt steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used lock insert for the steering column in the Mercury Cougar or Ford Mustang equipped with the fixed steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D

This clip clamps together the two edges of the shroud and sets into the mounting holes on the column. It is very hard to remove, and often the tab will break off very easily.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to this part can avoid several hundred dollars in damage. This precision...

Restored stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together.  We only sell this item on an exchange basis only, you are required to pre-send your restorable cores to West Coast Classic Cougar. These restored pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7...

This option REQUIRES sending your cores in advance. Used stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together. These pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7 convertible top mouldings. Limited supply of used and restored available.Replaces Ford part...

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Core grade windshield moulding for the passenger side windshield vertical stainless steel. 1969-70 Mercury Cougar and Ford Mustang coupes.Ford part number D0ZZ-6503148-B.

This driver side lower windshield moudling core is a great candidate for restoration for you do-it-yourselfers out there looking to save a buck. Or if you're driving around in a lower quality daily driver and you're missing this piece, we got what you need. Ford part number D0ZZ-6503149-B.

Used grade upper windshield moulding for any 1969-70 Mercury Cougar or Ford Mustang hardtop.  Ford part number C9ZZ-6503144-A.

Because these passenger side vertical windshield mouldings are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used "core quality" pieces. They are a great option if you have damaged or missing trim but plan to professionally restore your trim. Restorable, but not as nice as our "used" pieces. These are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have...

Core driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. This core grade unit is suitable for restoration or, if you are missing this piece, will fit right in with the rest of your driver quality trim.Ford part number C9ZZ-6503137-A.

Because this windshield moulding set is comprised of used original pieces, it will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A,...

Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, check out our video below. ...

Because these upper windshield mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check...

Because these passenger side vertical windshield mouldings are original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your...

Because these are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503148-B. *NOTE* If you have questions about your cores, checkout our video below. ...

Because these lower windshield mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of you who like to restore your parts yourself and are also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503149-B. *NOTE* If you have...

This original FoMoCo, five piece windshield trim set has been lovingly restored to far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well.Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A, C9ZZ-6503148-B, and C9ZZ-6503149-B....

Because these lower windshield mouldings are lovingly restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. They are an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503149-B. *NOTE* If you still have questions about your cores, check out our video below. ...

Because these side lower windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well.Ford part number D0ZZ-6503148-B. *NOTE* If you have questions about your cores, check out our video below. ...

Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, checkout our video below. ...

Restored passenger side (right hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. Because this windshield moulding / trim is a restored original piece, it will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. They are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your cores, check out our video below. ...

Because these upper windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check out our video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible has been lovingly restored far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option...

This original FoMoCo, six piece windshield trim set for the Mercury Cougar convertible. Because these pieces are original pieces, they will have far superior fit when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. The four upper pieces are wider than the coupe versions, but the lowers are the same (with about an inch cut off the ends). The trim is... trimmed so it will fit underneath the pillar trim pieces. *NOTE* If your trim has...

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes, will not lineup with factory holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1970 Standard model Mercury Cougars (XR7 models use a different relay/bracket) and 1970 Ford Mustang with convenience option. Additionally fits 1970 full size and mid sized Ford and Mercury cars with headlights on reminder option. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D0AB-10C838-A or D0AZ-10C838-A. ...

Used bracket for holding either the emergency flasher or turn signal flasher on many Fords dating from 1963. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches to one of two different relay mounting brackets. Couple of different designs were also used. Additionally there is also a different style of flasher mounting bracket. See our related items.Replaces Ford part number C3AB-13351.

Used bracket for holding either the emergency flasher or turn signal flasher. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches directly to the rear of the metal dash with a hex head machine screw.Replaces Ford part number C8AB-13351-A.

Used bracket for holding relays, either the emergency flasher or turn signal flashe. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number C9ZZ-14A301-A.

Used bracket for holding relays, either the emergency flasher or turn signal flasher. We find these mainly in 1970 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number D0ZZ-14A301-A.

Includes 2 hex head Screw & Washer Assembly aka "SEMS" bolts for the throttle cable bracket on the 1970 Cougar or Mustang equipped with the 428 Cobra Jet.

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the spacer on the passenger side. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the passenger side spacer. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please...

This direct replacement is the 2-1/4 inch H pipe only, and is for any 1970 Mercury Cougar or Ford Mustang with stock 2V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and custom made for dual exhaust on any 1970 Cougar and Mustang with the 2 barrel H code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351W, 1970 351C-4V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock 4V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 4 barrel M code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351C-2V, or 1971-73 Cleveland...

This direct replacement is the 2-1/2 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar Eliminator and Boss Mustang  with the G code Boss 302 engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1969-70 Mercury Cougar or Ford Mustang equipped with the 351W engine with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351W 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351...

This direct replacement is the 2-1/4 inch Y pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang  with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351-4V Cleveland engines, or 1971-73 351C engines. Please allow 2...

This reproduction 2 1/4" Tri-Y H pipe to be used with the Patriot style headers on your 1970 Cougar or Mustang.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Scott Drake style headers on your 1970 Cougar or Mustang.

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Right side axle, 28 spline 31-1/8 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Left side axle, 28 spline 27-1/16 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs.*Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. D0ZZ-4010-Assy 1970 9 Inch Rear End Housing Complete - Used Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1970 housings are different from 1969 9 inch housings. 1970 housings have a separate vent tube, 1969 vent tubes are used to hold...

Bare housing with proper axle pad spacing, vent location, and brake line attaching. For all 1970 Cougars. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Axles needed: Passenger side - 31-1/8 inches long, Driver side 27 inches long.

This retainer clamps together the two edges of the shroud and sets into the mounting holes on the column. The original is very hard to remove because of the saw blade teeth inside the grooves, and most times the tabs will easily break off. This reproduction will not have those teeth. Fits all factory 1970 Mercury Cougar and Ford Mustang, they use the same plastic collar around the column. If need be, simply widen the retainer for a better fit. *NOTE* For tilt column...

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

Nice reproduction of the Boss 302 throttle bracket as found on the G code Boss2 cars. Includes 1969-70 Cougar Eliminator and Mustang. Similar to the 428 Cobra Jet bracket but with an extended spring tab.

Bracket that mounts in the rear Carburetor mounting holes of all 1969 and 1970 351 Windsor 2 barrel or H code engines. Has the square hole that holds the factory throttle cable.Replaces Ford part number C9ZZ-9741-D.

Reproduction Concours Correct throttle return spring.Replaces Ford Part # : C9ZZ-9737-A

Used bracket that mounts in the rear Carburetor mounting hole of all 1970 351 Cleveland 2 barrel engines. Has the square hole that holds the factory throttle cable. This bracket is identified by the hump or curve midway between the carburetor mounting studs.Replaces Ford part number D0OZ-9741-A.*Note - Not for use with 351 Windsor engines, or M code 351C-4V engines.

9 inch rear axle snubber for all 1968-73 Mercury Cougar and Ford Mustang. Will work on 1967 9" differential but has slightly different angles as seen by our pictures. Bare bracket, rubber snubber sold separately.

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.