All Available Parts - 1970 Ford Mustang

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Thermostat Housing Gasket BY FEL-PRO® for the 351 Cleveland.

195 Degree Thermostat for the 351C, 351M or the 400. Factory spec temp for these engines is 192 degrees. Properly blocks off port that recirculates the water through the engine.

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

1970 Boss 302 radiator marked D0ZE-E1 and dated 9JD, we decipher the date as Sept 1969, 4th week. It has a 3 core construction as shown, with a rebuild tag. The upper and lower tanks and side brackets are all good. Fits any 1970 Boss 302 Mercury Cougar Eliminator and 1970 Boss 302 Mustang, it is dated for a October - November built car. Nice used assembly line, core radiator with original tanks. *Note - Does not have fittings for automatic transmission lines. All Boss 302 cars had 4 speed...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Correct core radiator for any 1970 Mercury Cougar or Ford Mustang with the G code Boss 302 engine. Has correct stamped Ford part number on the side strap, and lower tank without fittings for cooling lines. Core grade, will likely need recoring.Replaces Ford part number D0ZE-8005-E / E1

Found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1969 - 1970 all engines. One per car, one on the drivers side of the radiator. *Note - This is a shorter side shield than is found on the 1967 and 1968 Cougar.*Note - Block off plate not needed with the 24 inch radiators.

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

This shroud was discontinued by Ford in the mid 1990's. It really is no different in appearance from our reproduction but it does weigh a hefty 2.56 pounds and the reproduction weighs 1.76 pounds. Must have FoMoCo / part numbered shroud for that show quality BOSS 302 or 351C Eliminator. Just like our reproduction, the BARNUM BROS. lettering has been ground off. This was done because Barnum no longer made the shrouds for Ford in the latter years but the tooling still had their name on it.Ford...

SUPPLIER IS OUT OF STOCK UNTIL MAY 2024 Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

D0ZB-13A769-D-AGRADE Left side door wiring harness with decor interior as found on 1970 Standard Cougar (non-XR7's) with door courtesy lights and factory installed stereo. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights and factory door speakers only. Master part number D0ZZ-13A769-D. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

C9OE-H Application is for all 1969 428SCJ engines with the W code 4.30:1 axle ratio, and some instances it was found on 1970 428 super cobra jet engines. Fan description - 6 blade fixed pitch and 18 inches in diameter. Ford master part number C9OZ-8600-D. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9ZZ-8600-C. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler...

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

Nice reproduction of the 1970 - 1973 front adjusting bracket for the 351 Cleveland engines. These do not have any markings.

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

Special rear mounting bracket for 1970 Boss 302 Cougar Eliminators and Ford Mustang. Triangular shaped bracket as shown. Ford part number D0ZE-10A336-A.

D0ZB-13A769-B Left side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-B. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note* Does not include door ajar or factory stereo wiring plugs. ...

Tested and inspected neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

Tested and inspected neutral safety switch for the C-6 transmission installed in 1970 - early1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D1ZP-7A247-AA, or D0ZZ-7A247-B, SW 920.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-CNeed help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.

Plastic power window switch holder for the drivers door. This is the master switch holder or sleeve as it is called in the master parts catalog. Used starting in mid year 1970 through 1972 on Cougars, 1971-72 Ford Mustangs, and many 1970 full sized Ford and Mercury cars. Sleeve sold as is, without internal buss bars or mounting clips. Used, often times one of the tabs is broken, still functional, may need a bit of glue or tape to keep closed. Comes with the rear cover. *Warning - Take a...

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

Good used driver side (left hand) brake spindle for the Mercury Cougar or Ford Mustang equipped with front drum brakes. Our spindles shipped bare, without any hardware. We inspect every piece for spun bearings and any galling to the spindle shaft. These are getting hard to find because after market disc brake conversions require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Ford part # D0OA-3108-F.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unit is for use with a clutch pedal and has a shorter arm than power brake pedals. The brake pedal is shipped bare. Fits any 1969-70 Mercury Cougar or Ford Mustang.Ford part # C9ZZ-2455-B.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Hard to find little detail item that is often times missing and is correct for Ford Mustang as well.

Mercury Cougar AM-8 track radio. Motorola manufactured radio. May or may not work and wiring plugs may be cut. Good radio for reconditioning, often times the 8 track feature only needs a drive belt. Note that the "COUGAR" decal can easily be removed to make it look identical to the 1969 Cougar / Mustang unit which had no decal. The shaft lengths for the 69-70 unit are unique to these years. You can get other years to fit but you will find that your knobs do not rest in the same area and will...

We do not have any at this time . . . Very rare part in great condition. This was pulled from a very original 1970 H code XR7 with power windows, tilt column and AC. Technically not correct for 69 in that the shade of green would be darker in 1969. Why this car did not have the xr7 woodgrain delete plate we are unsure.

Used in conjunction with the front bracket, bolts onto stud protruding from the rear of your radio, rather hard to find once the original radio has been removed. One exception; 1972-73 Mercury Cougar and Ford Mustang AM/FM radios used a different bracket marked D2ZA-18888-AB. *Customer Feedback*"These guys have got to be the most professional I've dealt with in the 4 years I've been restoring my Mustang and Cougar. I have had nothing but pleasant conversations even though I tend to be long...

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Note that the "COUGAR" decal can easily be removed to make it look identical to the 1969 Cougar / Mustang unit which had no decal. The shaft lengths for the 69-70 unit are unique to these years. You can get other years to fit but you will find that your knobs do not rest in the...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

Carter manufactured valve with C8TE-9B289-B and 4490-S imprinted on the valves' cover. Another hard to find part with correct date codes specific to Boss 302. Ford part number C8TZ-9B289-A. These units are used, not tested and one should assume they are non-functional. These units are used, not tested and one should assume they are non-functional. *Note, we try to carry later manufactured 'Service replacement' Carter anti backfire valves which are in every way the same, but...

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Current dates: None - Specify...

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

Bolt for mounting thermactor smog pump to engine. Must be used in conjunction with thermactor alternator bracket and pump spacer. Bolt dimensions 3/8"-16 x 5.75" long.

This vacuum actuated door assembly was used on several performance motors without Ram Air. When extra air was needed under heavy acceleration the vacuum actuator opened the door on the side of the air cleaner base. The actuator on this unit needs to be rebuilt so this is considered a good core only.

C9OE-9C480-A 1969 and 1970 428 Cobra Jet (R and Q code engines) smog pump pulley with air conditioning, manual and automatic transmissions. 3 bolt smog pump pulley with a diameter of 5.10" inches. Ford part number C9OZ-9B447-A.

New old Stock rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang. NOS Ford, no Autolite or Motorcraft box. Ford Part Number C8OZ-9D612-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Reproduction rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang.  Replaces Ford Part Number C8OZ-9D612-C

This is a 1969 lid. The 1968 lid had several differences, most notable was the stamping wrinkles. This is  Flapper mid plate for use on non-shaker cars. 1969-70 Mercury Cougar with R or Q code engine with ram air. 1969 Mercury mid sized cars such as Montego, and Cyclone all with R code 428CJ or SCJ engines. Ford part number C9ZA-9600-C. This version is said to have been used starting in May of 1968, so there would have been some cars equipped with this mid plate.There are many...

D0ZF-9600-C Air cleaner base for the 1970 G code Boss 302 Eliminator engines. Could also be found under casting number D0ZF-9600-R. About 16.79" inches in diameter. Ford part number D0ZZ-9600-C.

D0ZF-9600-E Air cleaner base for 1970 Q code 428 Cobra Jet engines without the ram-air option. Identified with the rectangular vacuum operated valve on the driver side. Additionally the 1970 air cleaner has a star marked plug next to the snorkel on the passenger side. Starting in 1970 this base also received a plastic elbow for mounting the breather hose to the oil fill cap. About 16-3/8" inches in diameter. Could also be found under casting number D0ZF-9600-K. Ford part number D0ZZ-9600-E. ...

D0WF-9600-A Air cleaner base for 1970 Q code 428 Cobra Jet engines with the ram-air option. *Trivia - all 1970 Cougars with 428CJ were identified by a Q in the 5th digit of the VIN. Only those Cougars specifically with the ram-air option used this air cleaner base. Note - it is not the same as the 1970 ram-air Mustang base. Additionally the 1970 air cleaner has a star marked plug next to the snorkel on the passenger side. Starting in 1970 this base also received a plastic elbow for mounting...

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Original space saver tire marked F78-15 from a 1970's Mercury or Ford. GoodYear brand it has the larger hub size, bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is period correct for a Goodyear tire, but typically B.F. Goodrich was optional on 1968-69 Cougar or Mustang. *NOTE* Does not include...

Nice unused space saver spare tire for a Ford. Vintage Good Year brand tire with size F78-14. BF Goodrich is another common brand of tire installed for use with unique storage location, hold down, and inflation bottle. This one does not appear to have been inflated or used on the road. Still has the nubs on the face of the tire as shown.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

Unique to 1970 convertible only. Only with stock steel wheels and hubcaps. J bolt MPC lists the length as 6-1/4 inches, with 4 inches on the end threaded but actually there are only 2 1/2" on the threads. Threads 1/2-13.

Original scissors jack. We save the working ones that come to our yard. Hinge points should get little oil or a quick spray of WD-40. Wipe down the residual grease and oil and stow it in the trunk again! Notice the correct placement of the instruction decal. That's the tip of the day! *NOTE* There are multiple versions of this jack that differ in the area that makes contact to the rocker and the thread pitch. We will be sorting out those differences and posting our findings here soon. ...

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

These are getting hard to find considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Ford casting number D0OA-3108-F. Fits 1970 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction passenger side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69.  Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

This is a the economy version of our lower control arm assembly, with a spot welded on reinforcing plate. We are sorry, but we just cannot recommend this part. The Scott Drake premium version of this lower control arm is superior and costs less. In the picture, you can tell that it is lacking a rolled lip on the outer edge that the originals and the Drake Premium reproduction offers. This is a non-returnable item. Having issues with wobbly or loose steering? Check out our video on sloppy...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

D0ZZ-3304-A Manual steering drag link for all 1970 Cougar and Mustang and 1969 Boss 302 Cougar Eliminator & Boss2 Mustang with a non-power assist manual steering system.

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  ...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Inner tie rod end for 1970 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: D0ZZ-3A131-B.

Used driver side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561695 number possibly. Ford number D0ZB-6561695. ...

Reproduction moulding for 'upper windshield garnish' for any 1970 Mercury Cougar or 1969-70 Ford Mustang. This item not for 1969 Cougar hardtops or for convertibles. Item comes in black as shown, paint to match non-black interiors. This is a made in Taiwan part, and we recommend our used header mouldings. Ford part # C9ZZ-6503606-A.

Used actuator for the seat back release on the 1970 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...