All Available Parts - 1968 Mercury Cougar

Used standard grade "B" under hood main wiring harness that is located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All grade "B" electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar Standard models only with AMP warning light. Not...

Used grade "B" XR7 main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar XR7 models with Ammeter only. Not compatible with Standard model Cougar with...

Used standard grade "A" under hood main wiring harness that is located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7 model Cougar with Ammeter. Ford part # C8WY-14290-A.

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

These original FoMoCo headlight switches have been tested for both vacuum and electrical functionality. These old switches also come with the already attached "C" shaped spacer that mates to the dash. We all know how hard it is to get that spacer glued in on a new switch (which doesn't come with the spacer). Stamped witht the "Motorcraft" trademark and Ford part number C8WB-11652-C. 

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unique pedal that works with the wider collapsible 1968 steering column and with a clutch pedal. Shorter arm than power brake pedals. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare.Ford part # C8ZZ-2455-E.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Grade B 68 Radio Bezel for 1968 Mustang or standard Cougar. Holes often are modified for after market radio, might have broken upper mounting ear, pitting. Email for picture or detailed explanation of current stock on hand. Ford casting number C8ZB-6504567-CNeed some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.

Factory used and tested under dash wiring harness for all 1968 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the kick panel speakers in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1969-70 cars. White speaker wire goes to the passenger side speaker, and the orange colored wire...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

This was used only on the 1968 Mustang and standard Cougar, not for XR7. If you would like one that has been modified for an after market radio or you would not mind other minor blemishes (Or a broken ear) we have several that would save you money.Ford casting number C8ZB-6504567-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or...

This bezel is covered almost entirely by the face pad with clock. Only the small area around the radio actually shows once installed. This late bezel does not have the upper support, the early version is closed. Keep in mind we have bezels that have been altered for an after market radio for substantially less money.Ford casting number C7WB-6504567-B 68102-171 Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling. All 67-68 standard consoles had a storage...

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

1968 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine), or 1969 Boss 302 (G code Eliminator engine) smog pump adjusting arm, casting number C8OE-9B452-A. Ford part number C8AZ-9B452-B, C8AE-B casting number. Bolts sold separate. *Note - Only cars with manual transmissions received thermactor emissions in 1968.

Factory radio delete or block-off plate from a 1967-68 Mercury Cougar or Ford Mustang. Seldom seen part, roughly 5% of all 1967-68 Mercury Cougars were ordered without any type of radio from the factory. Similar story with the Ford Mustang, most owners added some sort of radio or stereo soon after delivery. The factory radio bezels were made from chromed pot metal, these radio delete plates are made from plastic and vacuum chrome plated. This used example pictured, has most of the plating...

1968 Mercury Cougar AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. NOTE* The one radio we have in stock at the moment has working AM, all buttons work, but the 8 track tape will not stay in position and needs fiddling - Call for advice. *NOTE* Does not include brackets or knobs. Ford master part # C7WA-18806-A, Chassis and Escutcheon...

Used non-functioning AM-8 track Motorola manufactured radio. These will not work and may have minor cosmetic issues from a past life. Ford part # C7WA-18806-A, Chassis and Escutcheon Assembly. Stamped T8MZ. *NOTE* Does not include brackets or knobs. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. Grade "A" condition guaranteed to work well. When you adjust for inflation these radios are actually less expensive now than in the day! 1968 was the first year for a AM-FM true "Stereo". 1967 was mono-stereo. Bendix was the original manufacturer of AM/FM radios in 1968. *HELPFUL HINT* 1968 and 1969 AM/FM radios are virtually the same except for the shaft lengths. Installing a 1969 AM/FM radio in your 1968 Cougar or Mustang with factory...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. This is a non-working unit that has a good crystal and knobs. All knobs seem to move freely. When you look inside the cooling holes on the top of the case you can see mouse droppings. Good unit to use for a modern upgrade core or good for restoration. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get...

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Specific to 1968 302-2V, and 302-4V all with manual transmissions - 3 speed or 4 speed. Same tube both sides, sold singly as a bare tube without installation hardware. Two total needed, one for use on each cylinder head. Must use cylinder heads with casting number C8OE-6090-L (302-2V) or C8OE-6090-K (302-4V).Pictured below are some shots of an unrestored J code 302 as taken from a low mile 4spd XR7 parts car. We thought we would post these pictures as a reference for those wanting to know what...

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

1968 390-4V all with factory manual transmissions and factory air conditioning. Pulley diameter 5.89" inches. Ford part number casting # C8AE-9B480-B. Mounting bolts sold separate.

Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. Tube dimensions 5/16" O.D. x 1.560" long. C6AZ-9A484-B

This is a reproduction, 3 bolt Thermactor smog pump pulley with a diameter of 5.49" inches for the Mercury Cougar GT-E with the 427-4V W code engine. C8OE-9C480-A marked on pulley. Ford part # C8OZ-9B447-B.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator adjusting bracket. It has the Ford stamped casting number of C8AE-10145-B. Ford part number is C8AZ-10145-B.

Bolt for mounting thermactor smog pump to engine. Must be used in conjunction with thermactor alternator bracket and pump spacer. Bolt dimensions 3/8"-16 x 5.75" long.

Used Grade A XR7 turbine style hubcap / wheel cover for the Mercury Cougar XR7. This unit was factory installed on the XR7 and will more than likely come with a faded center decal. These are almost impossible to find with a nice bright red center on the cars we drag into the yard. You should also expect that the black portions will need to be repainted and that there will be minor scratches around the perimeter, but no curb rash. This is a one year only hubcap / wheel cover that has 22 black...

New Old Stock dog dish style hubcap / wheel cover with the Mercury Man center cap for the Mercury Montego. This very rare optional unit was used in conjunction with the 14x6" 16 hole GT wheel commonly found on Mustangs and Torinos in 1968. This hubcap / wheel cover was offered only in 1968 and rarely seen on a Cougar as it would have only been offered as an over the counter option at your Mercury dealership. The more common application for this unit would be the 1968 Mercury Montego or...

NOS turbine style hubcap / wheel cover for the Mercury Cougar and Montego. These are the same as the 1969 Sports Special / 1968 Dan Gurney hubcap / wheel cover, but have the Mercury logo glued in the center. Ford part # C8GY-1130-G. Fits: 1968 Mercury Montego

NOS Grade A XR7 turbine style hubcap / wheel cover for the Mercury Cougar XR7. This unit was factory installed on the XR7 and was a one year only hubcap / wheel cover that has 22 black ribs. The Mercury MPC states that these caps were not to be sold in Pennsylvania. Ford part # C8WY-1130-D.Fits: 1968 Mercury Cougar XR7

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

This is a 3 bolt Thermactor smog pump pulley with a diameter of 5.49" inches for the Mercury Cougar GT-E with the 427-4V W code engine. C8OE-9C480-A marked on pulley.Ford part # C8OZ-9B447-B.

C8OF-9600-B For all 1968 S code 390-4V engines, regardless of GT or 6.5 badges. About 17.00" inches in diameter. Unique feature on this base is the addition of a round vacuum operated valve on the drivers side. Ford part number C8OZ-9600-B *NOTE* Please keep in mind that our hard to find parts like this are not always competitively priced with what you will find on the open market at swap meets and private party sales. Our primary intent in listing these is for our customers to use this...

C8OF-9600-B For all 1968 S code 390-4V engines, regardless of GT or 6.5 badges. About 17.00" inches in diameter. Unique feature on this base is the addition of a round vacuum operated valve on the drivers side. Ford part number C8OZ-9600-B. Our grade B base may have extra holes drilled, possibly dents or rust. Call for details on exact blemishes. Current base is missing the round vacuum valve completely.

This is an open style air cleaner assembly devoid of any snorkel. We send the tops out for a quality rechrome and we can inform you of what dates we have at any one time (date is stamped on bottom, 2 digits year and month, very faint). Most are happy to use the Mustang K code 289 HiPo reproduction air cleaner assembly we sell, which Mercury used on W code GT-E's with 427's. There's also a reproduction unit available.Ford part # C5ZZ-9600-C, C5ZF-9600-D. ...

C9ZE-9600-E Air cleaner base for the 1968 and early 1969 R code 428 Cobra Jet engine option. Additionally one way to identify this air cleaner is the dimple that clears the rear float screw found on the factory Holley carburetor. Early 1969 production is through 2/17/1969, after that date there was a vent added for automatic choke issues. About 16-3/8" inches in diameter. Ford part number C9ZZ-9600-E or C8ZZ-9600-A. Click on images to enlarge. ...

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

Used spinner hubcap / wheel cover for the Mercury Cougar. This was and optional inset spinner that bolted onto your existing hubcap. 1968 was the first year the dealer option was available. Ford part # C7MA-1130-F

Used / refurbished center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. These are always faded, so we've "restored" a few with Sharpies, as shown in the picture. Believe it or not, it works pretty well and allows the shiny aluminum to show through the red. Be advised that the sharpie treatment doesn't hold up very well to rain and weather, so this is best for garaged...

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out this video

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

This deck lock housing has been carefully stripped, polished and triple plated. You can send yours in in advance as an exchange or pay the core charge and return your old one later. Do know once a multi-faceted part like this has been stripped, polished and replated, some of the crisp, sharp detail will be muted and it will never again look just like factory. If you have extra cores we are buyers, especially if your lock assembly is complete. Check out this video ...

This is a decent used, grade B deck lock housing with nothing included except the studs. There will be a couple of blemishes that may include minor pitting but the cover stop in the bottom corner is intact. Perfect for a driver as very little of the chrome shows when this is installed, our reproduction cover will cover almost all of this part in the down position. Check out this video

This matched set is actually for a 1968 model Cougar but works just as well on a 67. The only difference being 1967 had squared off edges on the glove box button and 1968 had rounded edges which are safer in a collision.Ford Part # C7SZ-6543505-A/C6OZ-6206281-C or C7SZ-6543507-B (Glove box/Trunk lock kit)

This is a good used, grade A deck lock housing with nothing included except the studs. There will be no major blemishes or pitting and the cover stop in the bottom corner is intact. This is an impossible part to have restored and look OEM so finding a really good used one is important for a high quality restoration. Check out this video

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. Ford part number C7SZ-6543283-A. 1967 - 1968 only. Check out this video

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

Original space saver wheel and tire from a 1968-69 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-69 and pictures show a 1969 date. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

This is for the person who is missing it all. Includes all you need as seen in the picture and includes the reproduction chrome cover on a good used housing. Let us know in the comments whether you prefer a Standard or XR7 decal installed on the flip up door. Check out our video below showing how to easily remove and re-install your 67-68 trunk latch, lock, and cover plate and some info on getting a new key made. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Good used cylinder as taken from a 1967 - 1968 trunk lock housing. Will have minor damage but cosmetic only, 100% functional. Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit) Check out this video Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to...

This tiny little spring has a diameter no larger than a pencil. Its function is to attach the deck lock cover to the deck lock housing and to keep the deck lock cover closed. This is a unique spring to this application and rather hard to find. Check out this video

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Used servo cover from a 1967-68 Ford C-6 transmission. This cover has the big H cast into it, which designates it as an "H" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, with Mercury Cougar and Ford Mustangs with S code 390-4V engines. Cover only, marked C6AP-7D027-D.

Used servo cover from a 1969-71 Ford C-6 transmission. This cover has the big R cast into it, which designates it as an "R" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, from 1968-70 Mercury Cougar and Ford Mustangs with Q or R code 428CJ engines. Additionally 1971 Mercury Cougar or Ford Mustang with J or C code 429CJ engines. 1968-71 Ford and Mercury mid sized cars also with 428CJ or 429CJ. Cover only, marked C8OP-7D027-A.

Used servo cover from a 1968-69 Ford C-6 transmission. This cover has the big D cast into it, which designates it as an "D" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, for 1968 Mercury Cougar and Ford Mustangs with X code 390-2V engines. Additionally, 1969 Mercury Cougar and Ford Mustang with the S code 390-4V or 390IP engine. Cover only, marked C6AP-7D027-A.

Not 100% concours correct but close close in design to the 1968 - 1973 handle. Works well for 1967 as well. Replaces Ford Part Numbers: C5ZZ-17032-A, C5ZZ-17032-B ,C8ZZ-17032-A, D0ZZ-17032-A, D4ZZ-17032-A.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts...

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use.

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

This is a set of four die cast mouldings that attach via speed nuts at the bottom of your vinyl top. These do not pry off! Use your 1/4" drive ratchet with a deep 11/32" socket and small extension. You must remove your rear interior side panels to access the side mouldings. New speed nuts included, just in case..Ford casting numbers:Right rear: C7WB-65423A20-AWLeft rear: C7WB-65423A21-AWRight side: C7WB-65423A22-AWLeft side: C7WB-65423A23-AW*NOTE* These mouldings were color coded to your white...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. Economy replacement vinyl top that looks great and fits perfect. This...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Used driver side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561695 number possibly. Ford number D0ZB-6561695. ...

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Good reproduction but our used unit is a better value and will clean up just as nice.

This special bracket gets glued to the windshield. Rear view mirror bracket gets mounted to it. Glass bead blast it or just use a wire brush and it is ready to go!

Used passenger side outer bucket seat saddle hinge cover, for any 1968-69 Mercury Cougar or 1968 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561694.

Used driver side outer bucket seat saddle hinge cover, for any 1968-69 Mercury Cougar or 1968 Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand.  Ford number C8ZB-6561695.

Driver side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a 1970...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Grade A condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, passenger side only. Found on XR7 and most Standard model Cougars. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best...

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.