1969 - 1970

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

Unlike our un-restored used door glass trim and are sold in pairs only. If you are doing a concours correct restoration then these would not be for you as they have been "over restored" to a mirror like finish. The down fall of having such a mirror like finish is they get finger prints on them every time you touch them. The good part is they look HOT! Very nice touch to that resto-mod that cannot get enough bling.When sending cores, they must be in good shape or an upgrade core fee will apply....

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Restored decorative driver side sport special rocker panel scoops for the 1969 Mercury Cougar. To be eligible for the core charge refund, you must send in pitt free cores.

Restored decorative passenger side sport special rocker panel scoops for the 1969 Mercury Cougar. To be eligible for the core charge refund, you must send in pitt free cores.

Reproduction decorative sport special rocker panel scoops for the 1969 Mercury Cougar.Sold as a pair.

Restored decorative sport special rocker panel scoops for the 1969 Mercury Cougar. To be eligible for the core charge refund, you must send in pitt free cores. Sold as a pair.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 16 individual pads in a package.

This is a one year only, Cougar only part. I do not care what they told you down at the "Mustang Mega Barn", Cougar is different as it has mounting holes at the top and Mustang does not. The Mustang cover has no mounting holes at the top and resembles the 1970 cover. This may just be the most delicate part found on a 69 Cougar and is just behind good used interior sail panels in scarcity. Rarely do we have this in stock and we can almost assure you we will never be able to come up with the...

This nice used original part will have no broken tabs as seen on our grade 'B' version. This grade 'A' part will include two metal clip-on spacers as shown. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior.

This used original part will have a broken tab so you will have to use a over-sized washer or some other clever means of properly attaching it to the underside of your dash. This grade be part will not include the metal spacers seen on our grade 'A' part. Even with a broken tab this is a much better looking and fitting part than our economy reproduction. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. ...

This is a much better quality part then what you see offered elsewhere. 1970 is the only year 69-73 that Mustang and Cougar column covers interchange. You will need to paint this part to match your interior. Clips temporarily not available from supplier. No clips included at this time.

Quality reproduction lower column cover for the 69 Cougar.  Grommet sold separate. NOTE* This is not a Mustang part, the Mustang version is similar but has no upper mounting holes.

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.Click...

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...

Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...

Grade "A" driver side (left hand) bezel with no pitting, ready to install and use as-is. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some...

NOS driver side (left hand) taillight bezel for the Mercury Cougar.Ford part # D0WY-13489. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send...

Grade "A" passenger side (left hand) bezel with no pitting, ready to install and use as-is. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some LED taillight bulbs to your car? Here is...

Good used passenger side (right hand) driver grade quality bezel with minimal, light pitting, ready to install and use as-is. The pitting found on this grade "B" bezel will be light and almost entirely restricted to the top surface which means it will only be seen when the trunk lid is opened. Ford part # C9WB-13449 for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars...

Ultra rare, highly sought after NOS bezel. This is a costly part but when you factor in the price of a clean core and the $400 (approximate) cost of restoration, the cost is understandable. Keep in mind a restored part will never have the exact look of a NOS part. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car.Fits: 1969 Mercury Cougar1970 Mercury Cougar

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Sold as a set of twelve (two more than required), replaces Ford part #C9WY-6510182-A. From the factory there were five of these on each side for a total of ten per car. These same clips were also used on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products.Fits: 1969 Mercury Cougar1970 Mercury Cougar

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...

Left side factory stainless steel door guard.

Right side factory stainless steel door guard.

Stainless steel clip on guards for the rear edge of the 1969 and 1970 Cougar doors. Would have been part of the exterior decor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. Ford part number C9WY-6220910-A.

This restored passenger side (right hand) drip rail moulding / trim has had all minor dings and scratches removed and then polished to a mirror like finish. These puppies have been restored far beyond the quality that your car came with from the factory. These are sold outright, as one side only, or as a pair. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail mouldings / trim. The vinyl top...

These restored driver side (left hand) and passenger side (right hand) drip rail mouldings / trim have had all minor dings and scratches removed and then polished to a mirror like finish. These mouldings have been restored far beyond the quality that your car came with from the factory. These are sold outright, as a pair, or one side only. This is for the person that is striving for perfection with his show car. Most people are going to be satisfied with our grade "A" good used drip rail...

Clean cores are required for this service, cores that are turned in for this service that are kinked, heavily pitted or mouldings with several holes drilled into them are not worth restoring. That being said, often all of the gravel pitting usually found at the front cannot completely be removed as it would result in a product that will be too thin. Keep in mind that because these are restored mouldings, they will not have the black strips in place and will need to be painted on."...Don -...

Used driver side (left hand) and passenger side (right hand) convertible top boot moulding / trim for the standard Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Ford part # C9ZB-76423A19-A driver side, C9ZB-76423A18-A passenger side. *NOTE* If you have questions about your cores, checkout our video below. ...

Used grade "B" driver side (left hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years or...

Used grade "B" passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years...

This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520935-A. *NOTE* The use of this XR7...

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520934-A. *NOTE* The use of this XR7 unique trim requires the use of different...

NOS driver side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16075-A. This icon means that we're looking to buy this...

NOS passenger side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16074-A. This icon means that we're looking to buy...