All Available Parts - 1969 Ford Mustang

[No Description Provided]

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...

This A/C suction service valve fits on top of the compressor and is an exact copy of the original unit.Good for R-134A, but still compatible with R-12.Fitting sizes:Male end 7/8"Female end 9/16"

Grade B used A/C center vent for any 1969-70 Ford Mustang. This will some limited chrome pitting in the plating. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...

Used fresh air vent found in the driver side kick panel of all 1969-70 Mercury Cougar and Ford Mustang with or without air conditioning. Please also see the listing for new gaskets for installation.Replaces Ford part number C9ZZ-6501935-A.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Grade A used A/C center vent for any 1969-70 Ford Mustang. This will have almost perfect chrome plating, minor blemishes only, no pitting. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

Here is our NOS vacuum valve assembly which is fairly hard to come by these days. This unit is for Mercury Cougars or Ford Mustangs with integral or factory air conditioning. This part is good until an assembly date of 1/3/1972 and, if you want, we also have good used pieces in stock for your Coug or Stang as well. Ford part # C9ZZ-19B888-A.

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand.These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

C9ZZ-15520-B Backup lamp switch that mounts to the factory 4 speed shifter linkage. 69 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-842. *Note - 4 speed switches are different than the manual 3 speed switches.

NOS in the Motorcraft box C9ZZ-15520-B Backup lamp switch that mounts to the factory 4 speed shifter linkage. 69 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-842. *Note - 4 speed switches are different than the manual 3 speed switches.

According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C9ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

Backup lamp switch that mounts to the factory 3 speed shifter linkage. 69 70 71 72 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-947. Used up until 5-15-1972. Tested and working switch with wiring and plug.*Note - 3 speed switches are different than the manual 4 speed switches.

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

C9ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Grade A used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This is a real clean rust free cover but if you are wanting to save money, we have grade B's which will have a dent or creases for about half the price. Find the grade B here.Ford part number C3AZ-6366-A. ...

RAT-AM Original equipment 3 speed top loader 3.03 transmission from a 1969 Mercury Cougar with engine code H - 351-2V or engine code M 351-4V only. Ford master part number C9ZZ-7003-B.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

RAT-N2 Original equipment 3 speed top loader 3.03 transmission from a 1969 Mercury Cougar with engine code S - 390-4V only. Ford master part number C9ZR-7003-H. *Note - RAT-N or RAT-N1 could also be sustituted.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 =...

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Original dipstick tube. Application 1967 - 1969 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number C8ZZ-7A228-A.

Original dipstick tube. Application 1969 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. These are identified by being painted blue. Ford part # C9OZ-7A228-B.

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some dents and or scrapes. These were not painted originally, may have light rust that will clean up. Consider them Grade B used.

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.

This is a good used speedometer cable from a 1969 - 1970 Mercury Cougar with a FMX transmission. The cable housing has no burns and the fragile plastic squeeze clip that fastens it to the back of the speedometer is not broken. Keep in mind that some 1970 models use a two part cable. This cable will work in place of the two part cable seen on some 1970 cars. This cable measures 58 1/2" at its very most outer ends.

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

According to the MPC, this "Transmission Kick Down Control Shaft Rod" is used on all C6 Cougars and Mustangs in 1969, including the 390 and 428 Cobra Jet.  Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP with C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

Used on both 351w 2V and 4V FMX transmissions in 1969. Approximately 17-1/2" long with a black color code paint daub on the end closest to the carburetor. This is not correct for any 1970 Cougar equipped with a 351 Cleveland or Windsor motor. *NOTE* Although the MPC lists this part as 1969 only it does in fact apply to the 1970 Cougars equipped with the 351 Windsor two barrel motor. Not only did Ford confuse the public by giving both the 1970 351C 2V and 351W 2V the same engine code "H" in...

Good used original power steering lower hose bracket and retainer with a new reproduction insulator installed in place of the original crusty or missing insulator.This bracket is for cars with the big block routed power steering hoses.

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct length of power steering hoses.

NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

Larger sized retainer that screws to upper front lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these sometimes installed in the front position at the top of the interior quarter panel next to the window glass, mostly the front position is empty or the factory installed two of the smaller retainers. This retainer helps the top section of the soft trim panels from rattling. The...

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Used Two Spoke Steering Wheel Pad for the 1969 Mercury Cougar or Ford Mustang. Grade B pads will have minor scuffs and scratches and will need to be repainted. Keep in mind that the pad pictured is just a reference photo and not the actual color you will receive.  Leave a note in the comments section of your order and we will try our best to match your color.

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

Used angled chrome spacer for any 1969 Mercury Cougar or Ford Mustang. Good used part with very good chrome plating, usually one of the small locating tabs will be broken off of the back. Still a great value compared to the reproduction, and installs fine without the one tab on the back. Replaces Ford part number C9ZZ-11574-A.

Knob for the under dash ashtray on 1969 Mercury Cougar and Ford Mustang without consoles. Used in conjunction with a chromed bezel. Ford part # C9ZZ-65048B38-A.

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1969 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1969 fuel sending unit with 3 prongs (2 electrical and 1 alignment prong). The original Ford casting number was C9WF-9275-C. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1969 20 gallon fuel tanks. *Note -...

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

This listing is for a premium quality pair of 1968 - 1969 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the rear on the arm to the lower...

Nice used driver side strut rod that fits all 1968-69 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1968-69 Torino, Cyclone, Ranchero. 1968-69 strut rods are the same as 1970-73 strut rods, but 1968-69 rods have stepped down threads at the end. Ford part number C8OZ-3468-B. Sold as a bare strut rod, we also offer the used hardware for installation...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a better value than the Chinese rods we sell.*Note - 1970-73 strut rods work equally well.

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. This listing is for the driver side only. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage.*Note - 1970-73 strut rods work equally well.

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage. This listing is for the Passenger side only. *Note - 1970-73 strut rods work equally well. ...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

NOS glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Bezel for the knob for opening the under dash ashtray on 1969 Mercury Cougar and Ford Mustang without consoles.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1969 Mercury Standard model Cougars and all Ford Mustangs with 20 gallon fuel tanks. This is an original 1969 fuel sending unit with one electrical prong. Ford casting number C9WF-9275-A. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3 prongs (2...

Original Boss 302 carburetor spacer plate, bake-o-lite with metal tube angled to the side. See the link on the Boss 302 website here.Replaces Ford part number C9ZZ-9A589-C.

1969 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9AF-9510-M stamped on the carburetor air horn. Holley list #4279, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 428CJ Holley Carburetor - Core 428CJ service replacement carburetor, automatic C6 transmission - all 50 states. C9AF-9510-U stamped on the carburetor air horn. Holley list #4609, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. C9AF-9510-N stamped on the carburetor air horn. Holley list #4280, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

New carburetor spacer gasket, goes between the intake manifold and spacer plate. 1969 S code 390-4V or 390IP. Upper gasket, spacer plate to carburetor here.

1969 302-4V Boss Eliminator Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9ZF-9510-J stamped on the carburetor air horn with a 903 date code. Holley list #4511, 780 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

1969 351-2V Autolite 2100 carburetor, automatic FMX transmission - All 50 states. C9ZF-B stamped on the carburetor base, 1.23" venturi size and 356 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. C9ZF-D stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 390-4V Autolite 4300 carburetor, automatic C6 transmission - All 50 states. C9ZF-F stamped on the carburetor base, 1.25" venturi size and 600 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top.

1969 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-C stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

Factory cast iron exhaust manifold set, both a correct right C6OE-9428-A and left C7OE-9431-A side matching exhaust manifolds. With 1969 dates. *TRIVIA* 1969 390 S code Cougars were not technically the 390GT variety. An Autolite 4300 carburetor and a non-GT intake manifold changed the designation to 390IP for "Improved Performance."