Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 4901-5000 of 5303
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 11-0460 -
Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.
Availability: Out of Stock, On Order
Item #: 12163 -
These fuel door Mercury crest emblems are a close to original reproduction. They are an economical alternative to brighten up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. To remove your emblem we suggest grinding down the studs on the backside. To install the reproduction emblem you will need the 26120 trim clip.
Availability: Out of Stock
Item #: 22621 -
Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.
Availability: Out of Stock
Item #: 31711 -
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Availability: Out of Stock
Item #: 14401 -
Grade "A" doors have never been dented in, cracked in the door latch area or rusted in the corners. When you turn it over and inspect it, the seam it is not expanding from the inside out due to rust. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, no excuses, satisfaction guaranteed....
Availability: Out of Stock
Item #: 14402 -
Grade "A" doors have never been dented in, cracked in the door latch area or rusted in the corners. When you turn it over and inspect it, the seam it is not expanding from the inside out due to rust. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, no excuses, satisfaction guaranteed....
Availability: Out of Stock
Item #: 23603 -
You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 69-70 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...
Availability: Out of Stock, On Order
Item #: 26324 -
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
Spotlight!
Featured!
Availability: Out of Stock, On Order
Item #: 32446 -
COMING SOON Beautiful reproduction C pillar emblem for the 69 - 70 Cougar XR7. This part is also known as the shield or outside roof side ornament. The attention to detail on this exact copy is really impressive. Kudos to Daniel Carpenter Mustang for providing yet another outstanding part. Sold individually, 2 required per car. No core required. Replaces Ford part number: C9WB-65517A56-A Black plastic backer engineering number reads C9WB-65517C00-A Engineering number on back side of chrome...
Availability: Out of Stock
Item #: 33102 -
NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.
Availability: Out of Stock
Item #: 33103 -
NOS never installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender. Sold individually Replaces Ford Part #: C8OZ-16228-D.
Availability: Out of Stock
Item #: 13-0009 -
This is a used fuel door insert we have cleaned up, painted the background black and installed a 1967-1969 headlight door walking cat emblem on. The original 1970 ELIMINATOR piece that this resembles had a smaller sized cat so this is not exactly correct for your original 1970 Eliminator.
Availability: Out of Stock
Item #: 26204 -
Nice reproduction of the factory installed 390 engine designation ornament or badge. Also found on 1968 - 1969 Ford Fairlane, Torino, Ranchero, and Mercury Cyclone and Montego. Attaches with barrel nuts from the rear of the fender.Sold individuallyReplaces Ford Part #: C8OZ-16228-D.
Availability: Out of Stock, On Order
Item #: 15778 -
Reproduction emblem for the 390 engine designation. Never used on a Cougar, but an attractive emblem for customizing. Measures 3 1/8" x 3/4" and has two mounting studs.Replaces Ford part # C9ZZ-16637-D.
Availability: Out of Stock
Item #: 42370 -
Original part in Ford box, part number C9WB-16098-A, casting number as seen on back is C9WB-16098-B
Availability: Out of Stock
Item #: 42371 -
Very difficult to find, delicate aluminum quarter panel emblem in the original Ford box. Ford part number is C9WB-6525622-A, casting number on back reads C9WB-65291B62-AYou can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines.
Availability: Out of Stock
Item #: 42372 -
This version of the emblem was actually used on early 70's full-size Mercurys, and is almost identical to the 1969-70 version used on Cougars. In order to use it on a Cougar fuel door, the studs on the back will need to be trimmed down The only visible difference is the thinner / more numerous ridge lines in the red crest area than on the Cougar version. Casting number on this substitute emblem is D1GB-16607-AA.The original emblems were never sold as a stand alone part from Ford but rather an...
Availability: Out of Stock, On Order
Item #: 26105 -
These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD
Availability: Out of Stock
Item #: 41756 -
These were obtained from the original manufacturer and have never been mounted. Very rare find!
Availability: Out of Stock, On Order
Item #: 20663 -
Adhesive backed, located on the right side of your deck lid. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...
Availability: Out of Stock
Item #: 20212 -
Due to the fact these were glued on, they are often missing. Separate "XR" and "7", Grade B used, good for a daily driver. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid...
Availability: Out of Stock
Item #: 24760 -
These two emblems were sold separate when ordered as a service replacement part. We sell them as a pair. Located on the passenger side of the trunk, these are a peel and stick with no mounting studs. Ford part # C9WY-6542532-A & C9WY-6542532-BWe often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the...
Availability: Out of Stock
Item #: 41770 -
Rare find in NOS form! 1969 standard model Cougar, passenger side dash plate. Replaces Ford part number C9WB-6504460-A.
Availability: Out of Stock
Item #: 20373 -
This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. We rarely have an emblem this nice in stock for more than a few weeks of any one year as the tail was prone to breaking off as well as the "cats" other limbs. We do not list these hard to find parts here to...
Availability: Out of Stock
Item #: 19509 -
This little emblem was used only on the two spoke steering wheels from 1969 - 1973. We can pretty much guarantee one if not both of the two mounting studs will be broken but because of the way it fits into the recess of the steering wheel pad, gluing it into place is not a problem. The tail will always be broken and probably at least one leg is missing on this grade B part. While not an exact fit our 3 spoke wheel emblem cat will fit on this black background.
Availability: Out of Stock
Item #: 26458 -
This is a used coral with a new background decal and walking cat emblem. We ship the three parts unassembled so you can re-chrome the corral if you desire. The corral will not be perfect but it will not be heavily pitted either. You can expect the part you receive to resemble the one pictured here.Casting number: C9WB-18B000
Availability: Out of Stock
Item #: 20394 -
Good used pit free emblem. We now have the black background decal in reproduction form. Casing number: C9WB-18B000 Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...
Availability: Out of Stock
Item #: 20380 -
Good used center with no crack, missing paint or broken mounting tabs. This was used on all 1969 Cougars with a three spoke wheel except the XR7.
Availability: Out of Stock
Item #: 20433 -
Very rarely do we find one like this example that shows no sign of fading. This is for the person who is trying to achieve a very high level of preservation / restoration.
Availability: Out of Stock
Item #: 25846 -
Very rare find. Notice how unlike the reproductions the Mercury Head is fully raised. Ford part number C9WY-8213-A , casting number is C9WB-8B369-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if...
Availability: In-Stock Item
Item #: 24688 -
Good used emblem with both studs intact, no obvious pitting or scratches. This item will have a faded center decal, and you will need a new decal. You can either add a note to the order asking that we contact you about upgrading to an emblem with less fade for a upcharge, or get a reproduction decal here. Ford casting number reads C9WB-8B369-A ...
Availability: Out of Stock
Item #: 24841 -
C9ZZ-3K505-A Unique for the 1969 Boss 302 Eliminator and Mustang. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head.
Availability: Out of Stock
Item #: 11991 -
This reproduction stainless steel standard drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.
Availability: Out of Stock
Item #: 24081 -
C7SZ-3D600-A Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.
Availability: Out of Stock
Item #: 11989 -
This reproduction stainless steel power drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.
Availability: Out of Stock
Item #: 24565 -
For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.
Availability: Out of Stock
Item #: 24560 -
For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.
Availability: Out of Stock
Item #: 33132 -
New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A
Availability: Out of Stock
Item #: 32149 -
Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...
Availability: Out of Stock
Item #: 24644 -
Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...
Availability: Out of Stock
Item #: 23988 -
For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.
Availability: Out of Stock
Item #: 23990 -
Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.
Availability: Out of Stock
Item #: 23991 -
For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.
Availability: Out of Stock
Item #: 24072 -
For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.
Availability: Out of Stock
Item #: 18554 -
Used throttle cable for all 1969 Mercury Cougar and Ford Mustang with V-8 engines.Very hard to find one year only cable with no cracks. We rarely have this one in stock.
Availability: Out of Stock
Item #: 16156 -
NOS throttle cable for 1969 Mercury Cougar or Ford Mustang V-8. Version with the plastic tab for mounting to fire wall.Replaces Ford part #: C9ZZ-9A758-A.
Availability: Out of Stock, On Order
Item #: 11336 -
New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.
Availability: Out of Stock
Item #: 20655 -
This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969-1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall.
Availability: Out of Stock
Item #: 41047 -
Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.
Availability: Out of Stock
Item #: 14250 -
Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.
Availability: Out of Stock
Item #: 20192 -
This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
Availability: Out of Stock, On Order
Item #: 15037 -
Kit includes two brackets and grommets for routing battery cable between starter and solenoid on inner fender. Replaces Ford Part # : C5ZZ-14302-K
Availability: Out of Stock
Item #: 41132 -
Replaces Ford Part # C8AZ-2B164-A
Sold individually
Availability: Out of Stock
Item #: 30642 -
Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.
Availability: Out of Stock
Item #: 11360 -
Availability: Out of Stock
Item #: 24795 -
C9ZE-6583 Cast aluminum valve cover. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. Sometimes called 1969 Shelby valve covers. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of "Snake" finned aluminum valve covers.
Availability: Out of Stock
Item #: 20129 -
SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.
Availability: Out of Stock
Item #: 24796 -
C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...
Availability: Out of Stock
Item #: 23780 -
Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.
Availability: Out of Stock
Item #: 26132 -
Used seat belt bolt washer for the Mercury or Ford.
Availability: Out of Stock
Item #: 27361 -
Chromed engine oil dipstick as found on all 1969 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # C9ZZ-6750-A, Ford casting # C9ZE-6750-A.
Availability: Out of Stock, On Order
Item #: 31378 -
Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.
Availability: Out of Stock, On Order
Item #: 31577 -
Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.
Availability: Out of Stock, On Order
Item #: 11788 -
Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.
Availability: Out of Stock
Item #: 42048 -
The oil filter made by the original Ford supplier.
Availability: Out of Stock
Item #: 15281 -
This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.
Availability: Out of Stock, On Order
Item #: 26023 -
Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.
Availability: Out of Stock
Item #: 11-0259 -
Exceedingly hard to find in perfect used condition. Ford Part #:C9WY-6523209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for...
Availability: Out of Stock
Item #: 24748 -
Mounts to the rear of a 'turbo' style muffler. Left side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-B.
Availability: Out of Stock
Item #: 24749 -
Mounts to the rear of a 'turbo' style muffler. Right side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-C.
Availability: Out of Stock
Item #: 12107 -
NOS (New Old Stock) rear pancake motor for the rear quarter windows of the Mercury Cougar or Ford Mustang. These motors are often ruined because water has leaked down into the quarter panel where it has then seeped into the motor. Once water gets inside the case, the motor's days are numbered. This is because the interior of the case will eventually start to rust and it will seize the motor. This motor is a service replacement part and it would have been the motor your local dealership would...
Availability: Out of Stock
Item #: 31574 -
Used middle console support bracket. Held in place by 2 rivets midway under the console.
Availability: Out of Stock
Item #: 31736 -
Used rear console support bracket for the 69 Cougar or Mustang. Mounts under the leading edge of the storage compartment under the console.NOTE - 69 and 70 used different brackets
Availability: Out of Stock
Item #: 33511 -
Used front console support bracket. Held in place by 2 phillips screws at the front, under the console. NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.
Availability: Out of Stock
Item #: 23900 -
Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.
Availability: Out of Stock
Item #: 24488 -
This is the harder to find tail pipe hanger as it was only used on dual exhaust cars. Will have usable but cracked rubber. Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1969 dual exhaust Cougars, all engines. Ford part number C8WY-5260-B.
Availability: Out of Stock
Item #: 19413 -
Includes the two muffler hangers and two tail pipe hangers. Will not be overly rusty and will have decent rubber still intact. This set is for any 1969 Cougar equipped with factory equipped dual exhaust.
Availability: Out of Stock
Item #: 14174 -
Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.
Availability: Out of Stock
Item #: 13006 -
Used on the optional 1968 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1968 Torino and Mustang. Also used on the 1969 Eliminator 12 hole wheel so as to match the brushed center cap. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most...
Availability: Out of Stock, On Order
Item #: 31586 -
Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator, 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. WCCC is the only retailer offering these at present. Sold individually. Replaces Ford part number C8ZZ-1210-A. ...
Availability: Out of Stock
Item #: 30512 -
Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.
Availability: Out of Stock
Item #: 19483 -
These used taillight mounting washers are sold individually for your Mercury Cougar. Two different inside diameters on these, we have them mixed, because they are in such short supply. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....
Availability: Out of Stock
Item #: 31393 -
Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.
Availability: Out of Stock
Item #: 314047 -
Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.
Availability: Out of Stock
Item #: 25237 -
D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.
Availability: Out of Stock
Item #: 24869 -
C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.
Availability: Out of Stock, On Order
Item #: 26079 -
Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302
Availability: Out of Stock, On Order
Item #: 31010 -
Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.
Availability: Out of Stock
Item #: 41856 -
Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.
Availability: Out of Stock, On Order
Item #: 41567 -
Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A
Availability: Out of Stock
Item #: 24625 -
Application, 1969 - 1970 390IP / 428CJ & 428SCJ engines without air conditioning. Casting number 80B. 5-1/2" diameter and 7/16" sheave width.
Availability: Out of Stock
Item #: 24626 -
Application, 1969 Boss 302 Eliminators and Ford Mustang. Ford Part #: C9OZ-3A733-C Casting #: 90B. 6-3/8" diameter and 5/16" sheave width.
Availability: Out of Stock
Item #: 42303 -
1967 - 1970 390, 427 and 428 & 1969 - 1970 302 and 351: This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Includes both Pressure and Return hose that connect to the control valve. * 1967 - 1968 289 and 302: This big block routing is far superior to the...
Availability: Out of Stock
Item #: 11648 -
[No Description Provided]
Availability: Out of Stock
Item #: 19153 -
Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...
Availability: Out of Stock
Item #: 15404 -
We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...
Availability: Out of Stock
Item #: 11647 -
We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang without Power Steering Cooler.
Availability: Out of Stock
Item #: 11651 -
This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...
Availability: Out of Stock
Item #: 19163 -
Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.
Availability: Out of Stock
Item #: 20368 -
Used core bench seat taken from a Western parts car. Will need new foam and upholstery, but solid and complete with headrests. If you would like to put this in a 68 they are in fact identical once the 1969 single post headrests are removed. Does not include seat tracks.