Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 5201-5298 of 5298
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 31635 -
Used spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73. Ford part number D3FZ-1386-A. J bolt not included. This icon means that we're looking...
Availability: Out of Stock
Item #: 31638 -
Driver side seat back release catch for the 68 - 70 Cougar or Mustang.
Availability: Out of Stock
Item #: 14-0052 -
This is the original JB Weld. We decided to bring this stuff in as a convenience to you, our customers. Why not buy a pack so that the next time you need to bond something together, you'll have a couple of tubes handy? No need to get up and go to the hardware store. With just a few clicks of your mouse, you can have it at your door in a few days (more or less, depending on your location). Good for all sorts of projects around the house or garage.
Availability: Out of Stock
Item #: 25680 -
This is a very rare option for the 1969 - 1970 Mercury Cougar, Ford Mustang, and Shelby Mustang. It utilizes a center dash AC vent to blow fresh air into the cabin. The heater box is very similar to the standard heater box / plenum but has the vacuum switch and bracket mounted to the top. As our pictures will show, we are very careful to remove every nut bolt and clip. The unit shown was taken from a 1969 xr7 convertible equipped with a 390 with only 80k miles.Click on images to enlarge. There...
Availability: Out of Stock
Item #: 24669 -
This original Ford service replacement hood scoop is the same as a factory installed scoop except that it does not have the embossements for the hood grille used on the very first Ram Air Cougars (prior to September 1968) and it has extra mounting stud receptacles for use on multiple applications such as the Comet GT and the Mercury Cyclone. This version does have the reinforcing or webbing like the originals. Ford part # C9WB-16C664-C, C9GB-16C664-C, and D14B-16C664-AA. Found on the bottom. ...
Availability: Out of Stock
Item #: 13779 -
This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...
Availability: Out of Stock, On Order
Item #: 26024 -
Reproduction Eliminator hood scoop for the Mercury or Ford. Correct stud configuration, size and weight and far superior to our old scoop we offered. This scoop was made by using an original Eliminator scoop to make the mold. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. This unit will sometimes crack at the opening. The dimensions are just like the original and measure 21 5/8" at the widest point on the front, 25"...
Availability: Out of Stock
Item #: 13871 -
Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7G. The XR7G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar. Click on images to enlarge. ...
Availability: Out of Stock, On Order
Item #: 13956 -
Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.
Availability: Out of Stock
Item #: 14-1019 -
This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...
Availability: Out of Stock
Item #: 24847 -
Factory 15/16" sway bar for all GT-E 427-4V, 428 Cobra Jets, 428Super Cobra Jets, and Boss 302 Eliminators. Factory identified with a single 'Green' and single 'Yellow' paint stripe. We also carry the spacer plates separately. *Trivia - 1970 was the first year that a rear sway bar was available on a Cougar. A 5/8 inch rear sway bar would have been included with the competition handling package in 1970. This factory used front sway bar, does not include any mounting brackets or end link...
Availability: Out of Stock
Item #: 14-0048 -
Used plastic sheath that covers the bolted buckle end of where your shoulder belt attaches to the roof section of your car. Sometimes when removing the bolt from your shoulder belt, this sheath will tear if the plastic has become stiffened. Although it does not affect it's usage, sometimes it's best to simply replace it. NOTE: To remove this sheath, you will have to pull some slack from the seat belt up through the opening at the top in order to push up on the sheath to access the...
Availability: Out of Stock
Item #: 14-1017 -
This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...
Availability: Out of Stock
Item #: 14-0053 -
This is a complete set of Deluxe (chrome bands on buckles) safety belts removed from a 1969 hardtop minus torx bolt hardware. The set consists of two front retractors (they are not side specific) that measure 22" fully extended tip to tip, four lap belts bonded in pairs with the shoulder portion measuring 45" and the lap belt portion measuring 30" total length. The two male rear belts measure 20" and mount next to the rear interior panels and the female buckle side measures 36" fully extended....
Availability: Out of Stock, On Order
Item #: 12177 -
Window stop bolt for 69-70 Cougars. Each stop needs 2 bolts
Availability: Out of Stock
Item #: 10249 -
Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show.
Availability: Out of Stock
Item #: 14-1010 -
Both deluxe and standard use the same retractor in 1968 - 1969 and left is the same design as right. Grade "A" retractors will show no fading or cracks on the holster / retractor cover, good chrome buckle and may even still have the date code tag sewn in place. For no extra charge we will attempt to locate the correct date code for your car if you provide your cars build date. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. Check out our video "All about seat...
Availability: Out of Stock, On Order
Item #: 13713 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: Out of Stock
Item #: 11-0194 -
Grade B, Rear stop bracket for passenger side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, not included. Plan on replacing the felt, and most likely the rubber dipped section will be cracked. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A54-A. Do you have questions about Glue-In vs Bolt-In glass? How...
Availability: Out of Stock
Item #: 20688 -
Replacement nozzle for the side window channel 3M bonding adhesive. After a short time
Availability: Out of Stock
Item #: 11-0171 -
Used drivers side or left door window regulator for all 1969-70 Mercury Cougar and Ford Mustangs with glued in door glass. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, white plastic rollers, and captured steel bushing with clip. The regulator used on the bolt in glass, which became standard soon after the 1970 model year began, is...
Availability: Out of Stock
Item #: 20617 -
Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This item does not include any of the window trim so save yours for reuse. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be...
Availability: Out of Stock, On Order
Item #: 15747 -
Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar XR7. It was also used on the Standard model after 3/3/1969. This is part of the 14401 main under dash wiring harness.
Availability: Out of Stock
Item #: 24845 -
Used factory 3/4 inch sway bar for the FE 390 engine of 1969. This bar was factory identified with a single 'Yellow' and a single 'Blue' paint stripe. This bar is not to be confused with the Competition Handling Package sway bar which was optional on any 1969 Cougar. This factory used front sway bar does not include any mounting brackets or end link kits. Ford part # C9ZZ-5482-C.
Availability: Out of Stock, On Order
Item #: 11794 -
This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.
Availability: Out of Stock
Item #: 11793 -
One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes. Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.
Availability: Out of Stock
Item #: 15741 -
Used under dash wiring harness repair plug and pigtail to the ignition switch for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.
Availability: Out of Stock, On Order
Item #: 31550 -
Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock, On Order
Item #: 26668 -
Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.
Availability: Out of Stock
Item #: 24485 -
390 and 427 engines with C6 automatic transmissions. Shaft diameter 3 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory.Ford part number C8WY-4602-B Ask about slip yokes. Shipping is oversized due to length.
Availability: Out of Stock
Item #: 24486 -
428CJ engines with C6 automatic transmissions. Shaft diameter 3-1/2 inches. Length 49-41/64 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.
Availability: Out of Stock
Item #: 32702 -
Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. New Old Stock relay. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending...
Availability: Out of Stock
Item #: 24842 -
NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1969 West Coast Cougar organ donor car. We recommend a...
Availability: Out of Stock
Item #: 14475 -
Leaf Springs shipping time is 8-12 weeks.
All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring,...
Availability: Out of Stock
Item #: 24174 -
1967 - 1969 390-4V engines with 3 or 4 speed manual transmissions. 1969 - 1970 Boss 302 Eliminator 4 speeds. 1970 M-code with 3 or 4 speed manual transmissions. Shaft diameter 3 inches, length 53-1/32" measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.
Availability: Out of Stock
Item #: 24484 -
1968 - 1970 428CJ Drive shaft - Used All 428CJ's with 4 speed manual transmissions. Shaft diameter 3 inches, length 53 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.Ford part # C8WY-4602-A.
Availability: Out of Stock
Item #: 16-0047 -
Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.
Availability: Out of Stock
Item #: 25243 -
Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.
Availability: Out of Stock
Item #: 27302 -
*NOTE* Due to the difficulty in obtaining 69 aluminum trim we no longer sell these without first having you send us your cores. Keep in mind we pay well for quality 69 hood lip mouldings. Do not contact us with pretzel shaped parts, parts you have attempted to fix or flattened out parts. We need trim parts showing only minor dings / dents, scratches and dullness. Decent used trim part that would look good on a daily driver. This purchase requires that you...
Availability: Out of Stock
Item #: 16234 -
Used rear leaf spring retainer for 1967 -73 Mercury Cougar with competition handling or GT suspensions. Additionally it fits 1966-71 Mercury Comet / Montego / Cycolne, 1966-71 Ford Fairlane / Torino, all with HD or GT suspensions. Identified with a stamped number "2" on the top. The inside height is 1-29/32 or 1.91 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be...
Availability: Out of Stock
Item #: 31253 -
Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73. A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...
Availability: Out of Stock
Item #: 24593 -
The 69-73 looks the same as the earlier version once installed but the casting number will read C3AA-4906-C on the early unit and C9OA-4906-A on the 1969-73 version. We have found a few rubber bumpers marked D3Z... very few. See other listing for that one..
Availability: Out of Stock
Item #: 13154 -
NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.
Availability: Out of Stock
Item #: 12790 -
Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This unit is sometimes called eyebrow moulding and is a decent part that will look great on a daily driver level car. If you need new attaching clips with nuts, you can get them here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Ford Part Number C9WY-16074-A ...
Availability: Out of Stock
Item #: 12789 -
Decent used trim part that would look good on a daily driver. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Ford Part Number C9WY-16075-A
Availability: Out of Stock
Item #: 31059 -
Clean cores are required for this service, cores that are turned in for this service that are kinked, heavily pitted or mouldings with several holes drilled into them are not worth restoring. That being said, often all of the gravel pitting usually found at the front cannot completely be removed as it would result in a product that will be too thin. Keep in mind that because these are restored mouldings, they will not have the black strips in place and will need to be painted on."...Don -...
Availability: Out of Stock
Item #: 15441 -
Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...
Availability: Out of Stock, On Order
Item #: 15440 -
Kit comes with 4 metal clips, Ford part number C9WY-6510198-A and 10 plastic clips, Ford part number C9WY-6510182-A. Pictured is a complete set of 1969 rocker moulding clips. The 1969 Sports Special and the 1970 uses the same kit minus two metal end clips, if you have a 69 Sports Special or 1970 model please select that option so as to save $25.00. The 1970 aluminum rocker moulding is held by a Phillips screw on the back thus the need for front clips only. It is rare for us to get a set like...
Availability: Out of Stock
Item #: 32335 -
New old stock tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...
Availability: Out of Stock, On Order
Item #: 41550 -
Sold as a set of twelve (two more than required), replaces Ford part #C9WY-6510182-A. From the factory there were five of these on each side for a total of ten per car. These same clips were also used on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products.Fits: 1969 Mercury Cougar1970 Mercury Cougar
Availability: Out of Stock
Item #: 19456 -
Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...
Availability: Out of Stock
Item #: 20401 -
Excellent condition NOS rocker panel mouldings. These are original Ford parts made on original equipment back in the day. Sold as a pair, no hardware. Items sold will be better than the ones pictured.
The rounded edges on these mouldings go towards the rear, and the flat edge goes towards the front of the car. ...
Availability: Out of Stock
Item #: 25740 -
Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car.Fits: 1969 Mercury Cougar1970 Mercury Cougar
Availability: Out of Stock
Item #: 19469 -
Complete kit with 12 white plastic mounting clips, 2 black plastic mounting brackets that attach rocker mouldings to scoops, 2 aluminum rocker mouldings and 2 chrome plated scoops.
Due to supplier shortage, the metal rocker panel clips are not available at this time. Click Here to View Installation Instructions These are correct for 1969 only but can be used on any year 1967-1973 ...
Availability: Out of Stock
Item #: 15506 -
Good set of four diecast original top mouldings for both two tone paint Cougar hardtops and 1970 Cougars with a factory installed Hounds-Tooth checkered vinyl top. No broken studs, cracks, bends or chips. Originally these came painted on most cars, but in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, they came chrome plated. These mouldings will need to be re-chromed to look their best.
Availability: Out of Stock
Item #: 12724 -
This is a core five piece set of front windshield mouldings for a 1969 - 1970 Mercury Cougar. These trim parts need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard trim parts of that description. We do not recommend the reproduction, offshore mouldings that are available as they...
Availability: In-Stock Item
Item #: 31323 -
This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...
Availability: Out of Stock
Item #: 30564 -
New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...
Availability: Out of Stock
Item #: 15-0135 -
Used vacuum hose for the steering column release valve used in the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. Regular vacuum hose can be used to replace this hose if you are missing the original. However, it will not be correct. This nice original FoMoCo hose has the correct ribbing, stripes and comes with the firewall grommet. If you are missing this piece and you want your car to be right, this is a must have.
Availability: Out of Stock
Item #: 42346 -
This set of NOS mouldings has been one by one taken out of the wrapper, cleaned and carefully inspected one by one for imperfections or blemishes. Even factory blemishes are not included in this show quality, pristine set. At this price you need to know you are getting the best of the best. We will allow credit for your used or core wheel lip mouldings. You can send your used or core wheel lips in prior or after your purchase and we will call and discuss what amount of credit we will allow on...
Spotlight!
Featured!
Availability: Out of Stock
Item #: 33410 -
Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...
Availability: Out of Stock
Item #: 15-0403 -
Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Out of Stock, On Order
Item #: 13629 -
Reproduction Tilt Steering hose for the 69 Cougar or Mustang. Correct in every way, this reproduction is made to be an exact fit for your original hoses.
Availability: Out of Stock, On Order
Item #: 13605 -
Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...
Availability: Out of Stock
Item #: 15-0064 -
Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...
Availability: Out of Stock
Item #: 15-0065 -
Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.
Availability: Out of Stock
Item #: 15-0066 -
Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...
Availability: Out of Stock
Item #: 15-0067 -
Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without modification. Ford part number C8ZZ-13376-A or C8ZZ-13376-B.
Availability: Out of Stock
Item #: 15-0059 -
Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.
Availability: Out of Stock
Item #: 15-0057 -
Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...
Availability: Out of Stock
Item #: 15-0054 -
Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock
Item #: 15-0022 -
Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Availability: Out of Stock, On Order
Item #: 26548 -
Two-piece Stainless Rear Axle Brake Line Set 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any possible...
Availability: Out of Stock, On Order
Item #: 11441 -
Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...
Availability: Out of Stock, On Order
Item #: 33160 -
Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal.
Availability: Out of Stock, On Order
Item #: 11330 -
Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...
Availability: Out of Stock
Item #: 33173 -
Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops.
Availability: Out of Stock
Item #: 33176 -
O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.
Availability: Out of Stock
Item #: 31238 -
Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.
Availability: Out of Stock, On Order
Item #: 16211 -
Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern.
Availability: Out of Stock
Item #: 42027 -
If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...
Availability: Out of Stock
Item #: 53243 -
Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.
Availability: Out of Stock
Item #: 30365 -
Reproduction Chrome / Woodgrain steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.
Spotlight!
Featured!
Availability: Out of Stock
Item #: 32366 -
NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft. The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...
Availability: Out of Stock
Item #: 15-0169 -
This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Availability: Out of Stock
Item #: 15-0197 -
This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.
Availability: Out of Stock
Item #: 15-0144 -
Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.
Availability: Out of Stock
Item #: 15-0025 -
This rubber plug is found on the bottom side of 68 and 69 Cougars without tilt column. It covers the access hole for the bolt that removes the column head / collar. We notice that most cars do not have them in place. This could be due to over site at the factory or them being lost over the years as the car has been serviced. We have also noted that Dearborn cars rarely if ever have them present and San Jose built cars often have them in place. If you have a Dearborn built car and have this...
Availability: Out of Stock
Item #: 22560 -
Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529034-A.
Availability: Out of Stock
Item #: 22561 -
Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529035-A.
Availability: Out of Stock
Item #: 30265 -
This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520934-A. *NOTE* The use of this XR7 unique trim requires the use of different...
Availability: Out of Stock
Item #: 30266 -
This stainless steel driver side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. This NOS or new old stock part, often times it will have minor shelf wear. Included and attached is an NOS belt line weather strip. These stainless steel pieces shine up nicely with 0000 steel wool. No core or core charge required. Ford part number C9WY-6520935-A. *NOTE* The use of this XR7...
Availability: Out of Stock
Item #: 15-0133 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...
Availability: Out of Stock
Item #: 15-0046 -
One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...
Availability: Out of Stock
Item #: 15-0047 -
Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...
Availability: Out of Stock
Item #: 25813 -
Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...
Availability: Out of Stock
Item #: 26550 -
Two-piece Stainless Rear Axle Brake Line Set 67, 68 & 69 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any...
Availability: Out of Stock
Item #: 30530 -
Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: 8L27, November 27, 1968; 0E29, May 29, 1970. Please have your desired date in mind when calling or place it in the comments section of your on-line order. We have removed the peg leg gears and parts...