Home > 1969 Mercury Cougar
All Available Parts - 1969 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 4801-4900 of 5383
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 24713 -
Lamp housing with original glass lens, wiring pigtail with integral rubber body plug. Driver quality part. #97 Bulb available. We often find damaged wires with these lights left on our rear bumper cores. Guaranteed to work with no cuts or splices. Specified as a Cougar part in the Master Parts Catalog, but the wiring harness has imprinted on it C9ZB-13412-A. However, it is unknown whether or not it fits the Mustang.
Availability: Out of Stock
Item #: 32086 -
This used plug end will work on your 69 - 70 Standard or XR7 as well as the 69 - 70 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.*Does not include wires
Availability: Out of Stock
Item #: 32180 -
Used only on cars exported where speed limits were posted in KPH. Good used and working speedometer from 1969-70 XR7's and Eliminators. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 XR7 speedometers all look exactly the same, but the 1969 part number is...
Availability: Out of Stock
Item #: 65665 -
Grade "B" used backup light lens for passenger side 1969 - 70 Cougars. This lens will show some wear, and will also have a few minor cracks and scratches. Cracks inside the plastic from stress, not contact. Ford part number: C9WY-15514-A
Availability: Out of Stock
Item #: 12254 -
Grade "A" driver side (left hand) bezel with no pitting, ready to install and use as-is. Ford part # C9WB-13504 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some...
Availability: Out of Stock, On Order
Item #: 41716 -
Part of Ford part #C9AZ-15A201-C assembly. My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our hobby is really all about, making friends. Mark (mercurycougar.net)...
Availability: Out of Stock, On Order
Item #: 27453 -
Reroduction common gauge lens for the instrument cluster on the 1969 - 1970 Mercury. This lens is used on Standard / XR7 / Eliminator. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 27455 -
Set of three reproduction gauge lenses and one NOS clock lens for the standard Cougar with the optional clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 20414 -
New in box original FoMoCo. 1969-70 Standard model Cougars. Part number C9WY-15A000-ACheck out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 32925 -
C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...
Availability: Out of Stock, On Order
Item #: 33039 -
C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block.
Availability: Out of Stock, On Order
Item #: 41586 -
Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 25706 -
The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...
Availability: Out of Stock
Item #: 19452 -
Reproduction set of four lenses for an XR7 or Eliminator Cougar. The difference between Standard and XR7, is that the XR7 and Eliminator have a trip odometer reset button embedded in the lens at 6 O'clock. Correct Convex shape made from modern UV resistant plastic. Check out the first 3 minutes of video below that shows how to remove the dash cluster:Heater Core Replacement Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 19451 -
Reproduction set of four lenses for a standard Cougar without the optional clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...
Availability: Out of Stock
Item #: 31486 -
Used Bracket for mounting the Servo and accelerator Shaft on any 1969 Mercury Cougar or Ford Mustang with speed control. The whole assembly mounts to the firewall inside the passenger cabin. The Servo is the rubber bellows. We think the the Ford part number was C9ZZ-9C787-A. Ford part number 9C787.
Availability: Out of Stock
Item #: 31302 -
Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.
Availability: Out of Stock
Item #: 26198 -
Since the reproduction is no longer available anywhere, we've taken a used plug and our electrical department has pieced it together to make a useable plug. The Eliminator uses the XR7 harness but not the XR7 rocker switches in the center of the dash. This bypass plug completes the circuit left open when no XR7 switches are plugged into the harness.
Availability: Out of Stock, On Order
Item #: 11349 -
Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...
Availability: Out of Stock, On Order
Item #: 10637 -
1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.
Availability: Out of Stock
Item #: 31682 -
Used battery clamp to inner fender apron "L" bracket for 69 - 70 Cougars and Mustangs.This bracket secures the battery clamp to the inner fender apron. Ford Part # C9ZZ-10A705-A
Availability: In-Stock Item
Item #: 31764 -
Good used group 27 tray for 1969-70 Mercury Cougar or Ford Mustang. Assembly line installed group 27 battery tray. For those that want to keep it very original.Current tray has some erosion on the battery surface from use as shown. One little rust hole in the corner.
Availability: Out of Stock
Item #: 13-1113 -
New in-house cut vinyl applique for replacing the burl wood overlay on your 1969 Cougar console insert.
Availability: Out of Stock, On Order
Item #: 26487 -
Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.
Availability: Out of Stock, Discontinued
Item #: 26466 -
We recently unearthed a few of these unused club decals from the 1980's. "Cougars Northwest" was one of the earliest Cougar Clubs in the country. It folded back in 1988. It was amazing to witness the number of XR7G's, GTE's and Eliminators that would appear at the various club functions such as the annual "Cruise To Cougar Washington". Check out the very first Cougar in our video below! ...
Availability: Out of Stock
Item #: 26427 -
Reproduction 390 4V GT Emission Decal for the 1968 and 1969 Mercury Cougar / Ford Mustang
Availability: Out of Stock, Discontinued
Item #: 26366 -
Replica of the Autolite battery Stay-Ful tag advertising that the batteries 'Need water only 3 times a year'.
Availability: Out of Stock
Item #: 13609 -
This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...
Availability: Out of Stock
Item #: 26091 -
This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.
Availability: Out of Stock
Item #: 32716 -
This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.
Availability: Out of Stock
Item #: 32849 -
New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.
Availability: Out of Stock, On Order
Item #: 13691 -
New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...
Availability: Out of Stock, On Order
Item #: 12337 -
New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...
Availability: Out of Stock
Item #: 27582 -
NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.
Availability: Out of Stock, Discontinued
Item #: 10083 -
These is the correct driver side backing plate (sometimes called a splash shield) for 1968 - 1973 Cougars and Mustangs. Sold individually by side, each plate comes with the backing plate retainer. No other hardware is included. Although these plates fit the 68, they're cosmetically different in that 68 did not have cooling scoops.
Availability: Out of Stock, Discontinued
Item #: 10080 -
These is the correct passenger side backing plate (sometimes called a splash shield) for 1968 - 1973 Cougars and Mustangs. Sold individually by side, each plate comes with the backing plate retainer. No other hardware is included.Although these plates fit the 68, they're cosmetically different in that 68 did not have cooling scoops.
Availability: Out of Stock, On Order
Item #: 30403 -
Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...
Availability: Out of Stock
Item #: 30402 -
Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...
Availability: Out of Stock
Item #: 31945 -
Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...
Availability: Out of Stock
Item #: 27264 -
Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. 1969 had a weak design and the release levers were prone to bend and break off. 1969 used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob, which generally aren't interchangeble. Seldom in stock, please check out the reproduction version.
Availability: Out of Stock, On Order
Item #: 19943 -
This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.
Availability: Out of Stock, On Order
Item #: 13945 -
This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.
Availability: Out of Stock
Item #: 33095 -
NOS brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.
Availability: Out of Stock
Item #: 23816 -
C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.
Availability: Out of Stock
Item #: 24616 -
C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.
Availability: Out of Stock
Item #: 24618 -
C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..
Availability: Out of Stock, Discontinued
Item #: 23798 -
C2OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.
Availability: Out of Stock
Item #: 14-0012 -
4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Out of Stock
Item #: 13680 -
Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.
Availability: Out of Stock
Item #: 30447 -
Good used solid panel with all parts removed. Panel measures 19.5" x 39". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.
Availability: Out of Stock
Item #: 12213 -
This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!
Availability: Out of Stock
Item #: 12441 -
Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...
Availability: In-Stock Item
Item #: 31649 -
Reproduction frame used to stretch your headliner over on the interior side of your sliding sunroof panel. Since we do not have near enough of these to go around we also offer a cardboard template for purchase for those of you that would like to make your own. With the pictures we provide and the template one should be able to produce a reasonable reproduction.
Availability: Out of Stock, On Order
Item #: 12474 -
Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.
Availability: Out of Stock
Item #: 12476 -
Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.
Availability: Out of Stock, On Order
Item #: 14173 -
Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.
Availability: Out of Stock
Item #: 20652 -
Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...
Availability: Out of Stock
Item #: 11902 -
Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...
Availability: Out of Stock, On Order
Item #: 10138 -
Reproduction hood stripe kit in White for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...
Availability: Out of Stock
Item #: 22226 -
Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...
Availability: Out of Stock
Item #: 22227 -
Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...
Availability: Out of Stock
Item #: 15841 -
The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.
Availability: Out of Stock
Item #: 13728 -
Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!
Availability: Out of Stock
Item #: 20151 -
Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!
Availability: Out of Stock
Item #: 12472 -
Reproduction passenger side (right hand) quarter panel skin for the Mercury Cougar. These skins are made in America, but are low quality. 1969 and 1970 are not the same dimensions from the factory, the 1970 model year increased the wheel opening to allow for the optional larger tire size offered in 1970. The 1969 wheel opening measures at approximately 29-1/2" while the 1970 unit comes in at approximately 30-1/2". This reproduction measures approximately 29-1/2" at the wheel opening. ...
Availability: Out of Stock
Item #: 12253 -
Decent used, repairable valance. Getting to be hard to find without excessive filler or severe damage. If you would like pictures of the stock on hand email us as this is just an example of the part you get, not the actual part, damage varies as does price. We have repairable valances starting at $50.Ford part # C9WY-17620-A.Fits:1969 Mercury Cougar1970 Mercury Cougar This is our latest (and youngest) new hire! This is JD Rush who was named in part after his Great Grandfather, Jack Donald Rush...
Availability: Out of Stock
Item #: 18904 -
Good used Grade "B" valance. These valances may have some surface rust and a few dings or dents. You will definitely have to do work on these to get them ready for paint. We now sell a very high quality reproduction that is made of thicker material than OEM. Ford part # C9WY-6540544-A.
Availability: Out of Stock, On Order
Item #: 12455 -
New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.
Availability: Out of Stock
Item #: 12465 -
Reproduction patch panel for the rear of the driver side (left hand) quarter panel on the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...
Availability: Out of Stock
Item #: 12473 -
Reproduction patch panel for rear of the quarter panel on the passenger side (right hand) of the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...
Availability: Out of Stock
Item #: 12467 -
Reproduction patch panel for the front of the driver side (left hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...
Availability: Out of Stock
Item #: 12468 -
Reproduction patch panel for the front of the passenger side (right hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...
Availability: Out of Stock
Item #: 12469 -
Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...
Availability: Out of Stock, On Order
Item #: 15492 -
Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.
Availability: Out of Stock, On Order
Item #: 15493 -
Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.
Availability: Out of Stock, On Order
Item #: 15487 -
Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.
Availability: Out of Stock, On Order
Item #: 42399 -
Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.
Availability: Out of Stock, On Order
Item #: 11685 -
* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....
Availability: Out of Stock, On Order
Item #: 14301 -
Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...
Availability: Out of Stock
Item #: 20149 -
Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....
Availability: Out of Stock, On Order
Item #: 41630 -
These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.
Availability: Out of Stock, On Order
Item #: 41628 -
These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.
Availability: Out of Stock, On Order
Item #: 41632 -
These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "correct" restoration on their 1969-70 Cougar / Mustang / Shelby.
Featured!
Availability: Out of Stock
Item #: 31836 -
Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...
Availability: Out of Stock
Item #: 31862 -
Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.
Availability: Out of Stock
Item #: 31360 -
Our grade "B" fender extensions will have dings, scrapes or warping due to over tightening of studs. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-16A168-B, Mercury MPC # C9WY-16018-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...
Availability: In-Stock Item
Item #: 32319 -
New old stock 1969 Mercury Cougar Driver Side Front Fender Extension Ford part # C9WB-16A169-B, Mercury MPC # C9WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.
Availability: Out of Stock
Item #: 33473 -
This used header will be as good as you can get and it can be restored with some TLC. The part you get will be solid with minimal or no corrosion. Ford casting number C9ZB-76514A72-A
Availability: Out of Stock
Item #: 31581 -
Used condition pin and bushings for the 69 - 70 Convertible Cougar or Mustang.
Availability: Out of Stock
Item #: 12464 -
Used grade "B" passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years...
Availability: Out of Stock
Item #: 31304 -
Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.
Availability: Out of Stock
Item #: 12418 -
Used driver side (left hand) and passenger side (right hand) convertible top boot moulding / trim for the standard Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Ford part # C9ZB-76423A19-A driver side, C9ZB-76423A18-A passenger side. *NOTE* If you have questions about your cores, checkout our video below. ...
Availability: Out of Stock
Item #: 15347 -
Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...
Availability: Out of Stock
Item #: 15348 -
Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...
Availability: Out of Stock
Item #: 24756 -
Good used Grade "A" rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used,...
Availability: Out of Stock
Item #: 42392 -
Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Availability: Out of Stock
Item #: 42393 -
Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...
Availability: Out of Stock
Item #: 12-2003 -
We ask that you call or email us on this one. You can expect to pay upwards of $1000 for shipping to a US address, and that's not including the price of the roof.
Complete roof cut that includes the rear window opening and package tray. These roofs may or may not have the holes drilled for a vinyl top. If you have doubts of whether or not you need a roof with or without a rear window, we suggest that you remove your rear glass and peel back your vinyl roof and inspect the lower channel...
Availability: Out of Stock
Item #: 12-2005 -
We ask that you call or email us on this one. You can expect to pay upwards of $1000 for shipping to a US address, and that's not including the price of the roof.Roof cut includes the roof skin, 'A' pillars cut about 4 inches from the top, rear or 'C' pillars cut below the leaded seam. We have plenty of inexpensive, damage free roofs that have never had a vinyl top installed. If you want the pillars intact this triples the size of the crate and makes it cost prohibitive in most cases....
Availability: Out of Stock
Item #: 42376 -
We rarely have this one in stock. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money, so we suggest choosing Manually Calculate as your shipping option at checkout so we can manually calculate shipping costs. If you are ordering this item by itself, the quoted shipping cost should be accurate.Ford part # C9WY-17620-A.