All Available Parts - 1967 Ford Mustang

C5AZ-8509-J For use originally on 1967 289 engines without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single belt pulley 6.10 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.*This is one of the few water pump pulleys that did not have an imprinted casting number. Originally this pulley had an ink stamp. We will most likely be...

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

Sold in a set of eight, these are the same gauge steel as originals. Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Replaces Ford Part # C5ZZ-13190-K

This adjustable linkage kit connects the left track to the right track on a bucket seat. Original Ford part number C5ZZ-6561726-A. Ford description: Rod - Front Seat Track Tie. Listed for bucket seats 1965-1970.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.

For use originally on 1967 289 engines with California emissions (All 1967 DSO 52 and 53 Mercury Cougars), and without factory air conditioning. With extra cooling (20 inch wide radiator). 3 sheave pulley (three fan belts), with pulleys having diameters of 4-7/16 inches and 5-7/8 inches. Ford casting number C6OE-8509-A, was probably an ink stamp. These pulleys were made using a double sheave C6AE-8509-A pulley with a second smaller pulley welded on.

C6AZ-8509-F With air conditioning. Power steering and or thermactor emissions possible. 2 sheaves or 2 fan belts with a diameter of about 5-5/16 inches. Ford casting number C6OE-8509-B.

This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.

The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...

The knobs for the seat track release to adjust the position of the seat. The reproduction has a slightly deeper divot where you place your finger, and is slightly more round on the bottom, but a very nice reproduction. Replaces Ford Part #: C5AZ-6261753-BA.

Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Sold individually.Replaces Ford Part # C5ZZ-13190-K

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Correct for 1967 but fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. We also have the version with rectangular plates at the studs if you are wanting to match what you may have currently. ...

Large seat track spring for the latch. Used about 6-1/2 inches long, and about 9/16" thick.  Listed for bucket seats 1965-1970 Mercury Cougar and Ford Mustang. Likely fits other Ford seats, has a 1960 Falcon part number. Ford part number C0DZ-6461883-A.

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This kit fits the 1967 with a 1/4" control Valve Pressure fitting. You might want to verify that your 67 has the 1/4" fitting as many have been upgraded the the 5/16" fitting. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang without Power Steering Cooler.   Click this link for more clarity...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

1967 - 1970 390, 427 and 428 & 1969 - 1970 302 and 351:  This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Includes both Pressure and Return hose that connect to the control valve. * 1967 - 1968 289 and 302:  This big block routing is far superior to the...

Power steering hose kit w/ passenger cooler for the FE big block engines on the 67-70 Cougar or Mustang. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

Application 289/390 engines without air conditioning. Casting number AC 4-7/8" diameter and a 7/16" sheave width.

Application 1967 - 1968 - 1969 Cougar with either 289 / 302 / 351w engines with air conditioning. After 9-11-66. Casting number 7AD. 5" diameter and a 3/8" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Equalizer bar or "Z" bar for small block engines with a manual transmission. Both 3 and 4 speed manual transmissions. Replaces Ford part number C7ZZ-7528-G.

Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.

Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.

Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

Fits the 1967, 1968, 1969 and 1970 Mercury Cougar with the 390, 427, 428CJ or 428SCJ. These have the correct 20 coil spring, but are 1/8" longer than the Ford Master Parts Catalog calls for. Replaces Ford Part #:C7ZZ-7591-AR.

Exact reproduction of the 1967-68 Mercury Cougar and 1966-68 Ford Mustang clutch release fork to equalizer spring. Upper clutch equalizer to firewall, 289 and 302 engines. This unit will also work for 1969-70 Cougar and has the correct spring hook orientation. 66 - 68 Ford specs: 3-1/16" Long 40 Coils 69 - 70 Ford specs: 3-1/8" Long 36 Coils Replaces Ford part #: C3DZ-7523.

(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...

(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.

This attaches to the bracket mounted on the top side of your pedal hanger over to the clutch pedal itself. Replaces Ford Part #: C2AZ-7534-A.

Injection molded plastic stops underdash squeaking from clutch pedal return spring. 2 required per car. Replaces Ford Part #: C1DZ-7A630-A

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

Replaces Ford Part # : C7ZZ-7507-B

(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...

Reproduction engine side stud for the clutch equalizer bar or z-bar that fits a 289, 302, 351W, or 351C engines in the 67-70 Cougar or Mustang. 

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

Description: The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford Mustangs with a 3 or 4 speed manual transmissions. When people part out early Cougars they often leave this little detail item behind not fully understanding its function or rarity. Stood on end its length at the very longest point is 3 1/4". Its function is to but tension on your equalizer bar when it is...

Z bar return spring for all 1967-68 Mercury Cougar and Ford Mustang. This is the upper spring, proper color and spring tension from original. This is the economy version of the concours spring above. Made in China.

[No Description Provided]

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Add this item to your cart to download a free pdf copy of these instructions. On Checkout you will receive a link to download it! We've recreated this document from an original, being careful to keep the layout and font the same. Plain text version below: TECHNICAL INSTRUCTION (ATTACHMENT III TO SPECIAL SERVICE LETTER) Ford Division Service Campaign H-18 Lincoln-Mercury Division Service Campaign C-07 Power Brake Booster Replacement - 1967 Mustang with Power Disc Type Brakes - Booster Kit C...

Master clip kit which includes the following fasteners:Engine bayEngine feedFirewallFront crossmemberParking lightsPassenger side apron below relayRadio cable to dashKeep in mind that not all fasteners found on 1967 Courgars / Mustangs are in this kit.

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Replaces Ford Part # 359747-S

Sold as a Kit as Pictured.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used grade B trim / Beauty ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 14x6" 1968 SS wheel. This ring will have small scratches and or dings that will not be very noticeable.  Sold individually, four required per car as the spare did not come equipped with a center cap or trim ring. Replaces Ford part number C6ZZ-1210-A. ...

Used grade A trim ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 1968 SS wheel. No dings or scratches that cannot be buffed out. sold individually.Replaces Ford part number C6ZZ-1210-A.

Another great free download for you, our customer! In this free download, John Brower guides you through the installation of an overlay on your dashboard on your Mercury. Simply add this item to your cart and you will receive the download link via email after you complete the order.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

Sold individually. Zinc (dark silver)

Self threading white plastic. Used on front and rear valances.Sold individually.

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.

New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.

Set of 6 bolts for installing an OEM Ford timing cover marked C5OE-6059-A, which originally came on all 1967 Mercury Cougars with 289 engines or 1965-67 Fords including Mustang with 289 engines. 5 short and 1 long bolt in this kit.

Set of 10 bolts for installing an OEM Ford timing cover marked C3AE-6059-A, which originally came on all 1967 Mercury Cougars with 390 engines or 1963-67 Fords including Mustang with 352 / 390 / 410 / 428 engines. 10 total new bolts.*Note - this kit is not applicable to the 1968 and later Ford FE timing covers. See related items for other kit.

Reproduction stainless Allen head valve cover bolts. The bolts a re a bit longer to accommodate for the extra spacing required on the aluminum finned valve covers.

Reproduction black Allen head valve cover bolts. The bolts a re a bit longer to accommodate for the extra spacing required on the aluminum finned valve covers.

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.

These "Cal Custom" style Valve Covers look great and really compliment the Finned Oil Pan and Air Cleaner. These covers offer a true "old school" look. * Requires one of each of the following (sold separately): PVC grommet, oil cap grommet, and push on style oil cap.

1967 - 1969 Mustang, Cougar, Fairlane GT, and Ford vehicles with FE Series 390-427-428-428CJ engines. Chromed steel "Power By Ford" valve covers. Original equipment on all "S", "W" & "R" code big block Cougars. Super detail, domed chrome valve covers with embossed "Power By Ford" lettering. Also has internal baffles installed as original, price per pair. Click on images to enlarge. ...

D shaped, slightly lower profile than the D0OZ-6892 and designed for the thinner stamped steel valve covers, no Ford part number on part. Replaces Ford Part # C6AZ-6892

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Reproduction Ford blue painted valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

Reproduction chromed valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D.

Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...

OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675

Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302