All Available Parts - 1968 Mercury Cougar

Dark Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

White windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Aqua windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Nugget Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Light Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Saddle windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

This bumper bolt is sold individually and replaces Ford part # C4ZB-17758-A. It features the correct "button" head profile covered in stainless steel. Silver zinc with wax coating to extend plating life. Reduced shoulder height allows the nut to seat properly.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more...

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

Rear bumper guards and all the parts needed to install rear bumper guards on your 1967 - 1968 Mercury Cougar. Kit Includes:2 Rear Bumper Guards that have been triple plated to a level far beyond NOS standardsthe mounting kit consists of:a reproduction pair of bracketsnew fasteners. Mounting diagram not included, if you need one CLICK HERE for a printable version. No core exchange is required for this purchase. *NOTE* As is often the case, service replacement parts are painted and the...

This kit includes all new hardware, and both brackets. Mounting diagram not included (you can save and print the photo above). As shown, 1967 - 1968 rear bumper guards mount 17.5" from the center line of the car. Clip and bolt hardware kit will be new pieces.

Mustang bumper brackets do not work on Cougar. C7WY-17755-A.

C7WY-17767-A Front bumper mounting arm, 1967-68 Mercury Cougar, driver side.

Often passenger side brackets have battery acid damage thus the higher price for clean, undamaged passenger side brackets. C7WY-17754-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is...

C7WY-17766-A Front bumper mounting arm, 1967-68 Mercury Cougar, passenger side.

Good used set of crack free, bend free original brackets. These are Western parts that have never been exposed to road salt and can easily be restored to show quality standards.

part# 372434-SSold Individually.Head size: 5/8"Thread size: 7/16"

Reproduction Bumper Retainer for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Sold individually, two required per car. Right is the same as left. These Western rear bumper brackets are not heavily rusted, the threads are in perfect shape and they are not bent. Master part number C7WY-17A750-A.

Fits all models.

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Reproduction Front Bumper Guard Bolts & J Nuts for the 1967 - 1968 Mercury Cougar 

Reproduction pair of rubber front bumper corner fillers for your 1967 - 1968 Mercury Cougar. These install horizontally in the upper portion of your front bumper corners. Good used originals have become very hard to come by and that's why we've partnered with Daniel Carpenter to make these high quality reproductions. Do not confuse these with the previous inferior reproductions from a different supplier. Sold as a pair. Replaces Ford part #'s C7WB-17B951-B and C7WB-17B957-B ...

This driver side (left hand) rear quarter to bumper splash shield is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that it may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This looks better than the reproductions, in our opinion, and will cost you less money. Ford part # C7WY-6529031-A, and...

Used driver side (left hand) front fender to bumper slash shield for the Mercury Cougar. This is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This will look better than the reproductions, in our opinion, and will cost you less...

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Driver side (left hand) part number is C7WY-16304-B and the casting (or engineering) number imprinted on the part is C7WB-17B957-B. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...

Far better quality than the reproductions. The driver side (left hand) has a C7WY-16304-C Ford part number and the casting (or engineering) number imprinted on the top of the driver side part is C7WB-17B957-A. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need cleaning. Sold...

Used driver side (left hand ) grade "A" rear quarter to bumper splash shield. Far superior to the reproductions offered, these used fillers are crack free with minimal scratches. Just use soap, water and steel wool to clean them up. Nothing fits and looks like original FoMoCo!Ford part # C7WY-6529031-A, engineering # C7WB-65280A95-A, and is also marked with an L to denote left side.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The parts...

Far superior to the reproductions offered, these used fillers are crack free with minimal scratches and no missing chunks. Just use soap, water and steel wool to clean them up. Sold individually, this is a driver side only. Hard to come by, this 'Grade A' part will have pliable rubber, and not have visible cracks or damage when installed. *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The parts you will receive will be "as taken from a...

Anti rattle pad that hooks onto the top edge of the front bumper brackets. These created a soft cushion to prevent the stone deflector from coming into contact with the bumper bracket. These were originally held on with friction tape, same type of tape that Ford used to wrap the wiring harnesses. Sold individually, two needed per car.

Rubber protection sleeve that attaches to the front bumper brace tubes. 1968 Mercury Cougars only due to the front side marker lights. Attaching point is where the front side marker wiring harness touches the bumper brace. Pliable rubber hose slit as shown, about 1-1/2 inch long for those that want to make their own. Looks like 15/16" ID thin wall rubber tubing. Sold individually, two needed per car.

Quality exact reproduction rear quarter to bumper splash shields, also called bumper side fillers for the 67 - 68 Mercury Cougar.Sold as a pair.

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

This option includes paying a core charge. By choosing this option, the re-chromed item you receive will have started the re-chroming process as an average quality core.We highly recommend that you send us your core first. Here's why: We can core match your bumper guards. Bumpers guards that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the...

These are the brackets required to mount the optional rear bumper guards. They mount behind the rear valance and are often overlooked when people part out a Cougar. *NOTE* As is often the case, service replacement parts are painted satin black and the originals installed on the assembly line were left natural. The mounting brackets are in fact supposed to have a natural finish if your car came with them from the factory.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 16 individual pads in a package.

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

This is the grade “B” driver side (left hand) front bumper corner filer and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Driver side part number...

This is the grade “B” passenger side (right hand) front bumper filler and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Passenger side part number...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Passenger side (right hand) part number is C7WY-16304-A and the casting (or engineering) number imprinted on the part is C7WB-17B951-B. The Mercury MPC refers to these as "anti squeak pads." Normal 0 false false false EN-US X-NONE X-NONE Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be...

Far better quality than the reproductions. The passenger side (right hand) has a C7WY-16304-D Ford part number and the casting (or engineering) number imprinted on the top of the passenger side part is C7WB-17B951-A. The Mercury MPC refers to these as "anti squeak pads." Normal 0 false false false EN-US X-NONE X-NONE *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...

Far superior to the reproductions offered, these used fillers are crack free with minimal scratches and no missing chunks. Just use soap, water and steel wool to clean them up. Sold individually, this is a passenger side only. Hard to come by, this 'Grade A' part will have pliable rubber, and not have visible cracks or damage when installed. *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The parts you will receive will be "as taken from...

This passenger side (right hand) rear quarter to bumper splash shield is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that it may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This looks better than the reproductions, in our opinion, and will cost you less money. Ford part # C7WY-6529030-A, and...

Used passenger side (right hand ) grade "A" rear quarter to bumper splash shield. Far superior to the reproductions offered, these used fillers are crack free with minimal scratches. Just use soap, water and steel wool to clean them up. Nothing fits and looks like original FoMoCo!Ford part # C7WY-6529030-A, engineering # C7WB-65280A94-A, and is also marked with an R to denote right side.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The...

Used passenger side (right hand) front fender to bumper slash shield for the Mercury Cougar. This is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This will look better than the reproductions, in our opinion, and will cost you less money....

This Grade A quality ashtray lid was located at the rear of the console and was used on all 1967 - 1968 Mercury Cougars except the 1967 standard model and the 1968 XR7G. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish and a slightly taller lower section. The removable ash receptacle is sold separately.Ford part # C7AZ-6330714-A.

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front on flexible rubber back. Includes chrome knob. Different from the 1967 door in that it has the much wider handle. Ford part # C8ZZ-6506024-A. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover...

In the form that is shown, the application for this plastic base is for a non AC car with an automatic transmission. It can easily be cut for an A/C equipped car or a manual transmission, we offer the modification at no cost.  This base is designed for a 1967 standard with AT model but with slight modifications it will work on all models 67-68 manual and AT transmission vehicles. Made from modern injection molded plastic, you will find this is a very sturdy base and the textured...

Used driver side (left hand) rear bumper guard for the Mercury Cougar. The chrome plating was pretty low quality back in the day and this unit will have some scratches and pitting as it is an almost 50 year old original part. Mounting diagram not included, if you need one CLICK HERE for a printable version. Ford Part #: C7WY-17985-A. *NOTE* Driver side is stamped with an "L" on the backside. ...

Used passenger side (right hand) bumper guard for the Mercury Cougar. The chrome platting was pretty low quality back in the day and this unit will have some scratches and pitting as it is an almost 50 year old original part. Mounting diagram not included, if you need one CLICK HERE for a printable version. Ford part # C7WY-17984-A. *NOTE* Passenger side is stamped with an "R" on the backside. ...

Exact reproduction of originals but improved!On the originals, the mounting holes did not line up properly so we made them fit perfect!Made using the original Ford blue prints and a NOS original for the pattern. Replaces Ford part numbers C7WY16B555-A and C7WY-16B554-A

These brackets are required to mount the optional rear bumper guards. They are not an exact reproduction but functionally they are spot on.Installation hardware is hard to come by, so you should hang on to yours and re-use them.Sold as a pair

This light was used on 1967 - 1968 Mercury Cougar and 1967-68 Ford Mustang Consoles with the roll up door. Not for use on the XR7 console. Notice the light lens is painted white on one half unlike the reproduction lens that is all white.  Assembly will not come with a working bulb, you can find the correct 1891 replacement here, or grab an 1891 LED here. You can find a replacement lens here. ...

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

Reproduction rear bumper for the 67-68 Cougar. Constructed from steel and triple chrome plated via chromium-nickel electroplating for enhanced corrosion resistance, durability, and shine. Made to match the factory original in both looks and fitment. Please know that chrome cracking from the installation of bumper bolts on these bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten...

NOS front bumper for the 67 - 68 Cougar. Only a piece of the original packaging is left, but this is an original Ford bumper with the original part number sticker on the back. Will show some shelf wear and minor blemishes as shown in the photos. And since it's NOS, there's no core charge. Ford part number C7WY-17757-A Also, if you are having difficulty aligning your bumpers, you really need to check out this really cool tool! We have one for loan if you are in the area It only takes...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems.Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too. ...

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

Reproduction disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. This unit has the correct stampings, rubber inner gasket, and is considered show quality. This cap will only fit master cylinder part # 15298.Replaces Ford part # C7AZ-2162.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang / Torino1968 Ford Mustang / Torino 1969 Ford Mustang / Torino 1970 Ford...

Reproduction seal for the lid of the brake fluid reservoir for a power disc brake equipped Mercury Cougar or Ford Mustang.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

New master cylinder for the Mercury Cougar or Ford Mustang equipped 4 wheel power disc brakes. This unit can be used with the Bendix and Midland boosters. Bore size: 1" WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

New reproduction power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in the back.  This unit has a 1" bore and includes a new cap and diaphragm as shown.  Unlike many others you will find, this unit does not need brass line adapters to fit your factory lines, they are correctly sized, will not interfere with your shock tower and ready to bolt on.   Has proper threaded line size for OEM or...

Reproduction disc brake master cylinder cap in gold cadmium for the Mercury Cougar or Ford Mustang. We have compared this cap to our originals, and the stamping does not match any of our originals, but the manufacturer claims that the scripting is correct. Also available in chrome!  This cap will only fit master cylinder part# 15298Replaces Ford part # C7AZ-2162-B. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar...

Reproduction adjustable disc brake push rod set for the Mercury Cougar or Ford Mustang. When you convert to manual disc brakes, this kit eliminates excess pedal travel and insures quicker braking response. NOT for power disc brakes. For Manual disc brake cars ONLY.

Reproduction power brake booster filter for the Midland brake booster used on the 1967-68 Mercury Cougar or Ford Mustang. The Midland booster actually provided better stopping power than the later 1969-70 Bendix booster. The down side is that you will be lucky to get 10 years out of the Midland booster as they are not nearly as reliable of a design as the Bendix unit.Ford part number C3TZ-2A346-B,

Reproduction black 3D printed brake booster filter retainer for the Mercury Cougar and Ford Mustang. Same functionality at the originals, it fits between the brake booster and master cylinder in the aluminum master cylinder spacer. You can find the filter here.

Used assembly line, white plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white. You can find the filter here. ...

Used spacer or retainer, for the 1967-68 Mercury Cougar and Ford Mustang. This filter retainer spacer is made of aluminum and is for the Midland manufactured brake booster. It fits between the master cylinder and brake booster. Nothing beats original FoMoCo!The Ford part number may be C5AZ-2B157-A. 

Nut for attaching brake boosters in any 1967-73 Mercury Cougar or Ford anything, including Mustang. 3/8 - 16 zinc plated nut with serrations.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2".  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Reproduction spacer kit for your 1967 - 1969 Cougar or Mustang Midland power brake booster.

This all inclusive vacuum booster master rebuild kit is great for the do it yourself-er or the person that would like to retain their original case / housing. Also a great option for the out of country customer that does not want to pay expensive shipping to return a core. Keep in mind this will only work on a MIDLAND unit with the removable band. Also be aware that our rebuilt units we sell do not have 100% new parts as shown here as our builder will reuse multiple parts that can be cleaned...

Reproduction bellows and clamp for your 67 - 69 Cougar or Mustang Midland power brake booster.

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.Diameter 7 1/4"

Reproduction rear boot for your 67 - 69 Cougar or Mustang Midland power brake booster.

Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.

Fits any model that used the banded Midland-Ross booster. This Bakelite hub can be seen when you remove the dust boot. It is a very brittle fragile part that gets broken when you drop the booster, attempt to bleed the brakes with the engine running or install the wrong brake pedal.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

New premium reproduction tear drop power disc brake master cylinder for the Mercury Cougar or Ford Mustang equipped with factory power disc brakes in front and drums in back. Has proper threaded line size for OEM or replacement brake lines, 3/8-24 and 1/2-20. The main difference between this unit and our economy version is cosmetics, as this premium unit comes with the correct "tear drop" casting; other difference to consider are this unit has a 1" bore, instead of 1 1/8"...

This brake booster to master cylinder spacer was used on many Ford / Lincoln / Mercury products beginning in 1962. Many do not even realize a foam filter is supposed to be sandwiched between the plastic filter cover and die cast aluminum spacer as brake fluid saturates them and the delicate foam filter element deteriorates. The originals were white but after many years become stained. Service replacement units were often black. These spacers were used on Thunderbird Cyclone Torino Fairlane...

If you watch our booster video you will see we have a clear distaste for most of the offshore boosters offered today. What caught our attention about this new product was that it looked like a real deal 67-9 Midland brand booster! We went the next step and sent it to the world's foremost leading authority on said boosters (Booster Steve in Portland OR) so he could put it through some rigorous testing and examination. At first he was very hesitant to have us waste the postage to send it but two...

Reproduction black 3D printed brake booster filter retainer for the Mercury Cougar and Ford Mustang. Same functionality at the originals, it fits between the brake booster and master cylinder in the aluminum master cylinder spacer. You can find the filter here.

This all inclusive vacuum booster master rebuild kit is great for the do it yourself-er or the person that would like to retain their original case / housing. Also a great option for the out of country customer that does not want to pay expensive shipping to return a core. Keep in mind this will only work on a BENDIX unit with the crimped band. Also be aware that our rebuilt units we sell do not have 100% new parts as shown here as our builder will reuse multiple parts that can be cleaned up...

This after market adjustable proportioning valve is far superior to the original equipment. Fully adjustable for tuning front to rear brake bias. Requires some routing modifications of brake lines for proper fit. Includes adapter fittings. Replaces Ford part # C5ZZ-2B091-A, or C7OZ-2B091-B.Fits: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang 1968 Ford Mustang 1969 Ford Mustang 1970...

This switch mounts on the brake junction block to warn the driver of potential brake failure through a warning light on the dash. Replaces Ford Part #: C8AZ-2B264-A.

Used disc brake distribution block for 1968 and 1969 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch or Proportioning valve. Look for our listing for 1968 - 1969 Brake Distribution Block Assembly for a unit with the switch and proportioning valve with steel flared connecting lines. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # C8ZZ-2B257-A. Here’s a video to help you...

These are the two lines that connect the proportioning valve to the distribution block on the Mercury Cougar or Ford Mustang.Proportioning valve is not included in this kit, only the two brake lines. Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Used proportioning valve for the 1967-68 Mercury Cougar or Ford Mustang. This is a cylindrical shaped brass valve, some times called the pressure control valve, brake valve or 'cigar' valve. For 1967 Cougars, this valve is most often found at the junction of the high pressure hose back at the rear end. 1968 had it connected to the distribution block on the driver side firewall. Will come with the C7OE-... stamped valve. Starting in 1969 the valves had a C9OE... Ford part number. These are used...

New disc brake proportioning valve / distribution block seal and rebuild kit for the Mercury Cougar or Ford Mustang / Torino. Every 1967-69 Cougar, Cyclone, Torino, Ranchero and Mustang equipped with disc brakes needs this kit even if you are not leaking fluid yet. These little "O" rings are always "rock hard" after 40 plus years because the original O-rings are composed of a BASIC nitrile compound. After several years, the absorption of brake fluid will change the molecular structure of the...