Home > 1968 Mercury Cougar
All Available Parts - 1968 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 601-700 of 5493
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 32363 -
Used under dash wiring harness repair plug and pigtail for the passenger side (right hand) door jamb switch for the 1968 Standard Model Mercury Cougar. Used on the passenger side of 1968 XR7 Cougars. For two pins on your door switch, also has three wires as shown. This is part of the 14401 main under dash wiring harness.
Availability: Used / Wrecking Yard Item
Item #: 32388 -
Used under dash wiring harness repair plug and pigtail from the wiper motor to the main 14401 harness for the Mercury Cougar. We also carry the mate for this pigtail. You can check wire colors for correct pigtail.
Availability: Used / Wrecking Yard Item
Item #: 20611 -
Used driver side (left hand) grade "A" clear door glass for the Mercury Cougar and Ford Mustang Coupe. This unit it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Comes with the surrounding affixed stainless steel trim. Mustang...
Availability: Used / Wrecking Yard Item
Item #: 20612 -
Used grade "A" clear passenger side (right hand) door glass for the Mercury Cougar coupe. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. This door window comes with surrounding affixed trim. Mustang hardtop and coupe...
Availability: Used / Wrecking Yard Item
Item #: 23479 -
Used passenger side (right hand) grade "B" tinted door glass for the Mercury Cougar coupe or Ford Mustang coupe. This item will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This door window comes with surrounding affixed trim. Mustang hardtop only, convertible is different.Ford part # C7ZZ-6529710-D. *NOTE* Air conditioning cars were supposed to have SUN-X...
Availability: Used / Wrecking Yard Item
Item #: 23444 -
Used driver side (left hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe. This item will not have the faint green tint like the SUN-X factory tinted glass. Good used driver quality door glass with multiple minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This door window comes with surrounding affixed stainless steel trim. Hard top Mustang only, convertible and fastback are different.Ford part #...
Availability: Used / Wrecking Yard Item
Item #: 23445 -
Used driver side (left hand) grade "B" tinted door glass for the Mercury Cougar or Ford Mustang Coupe. This item will have the faint green tint and be marked SUN-X. Good driver quality used door glass with multiple minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This door window comes with surrounding affixed trim. Mustang hardtop glass only, convertible and fastback is different.Ford part # C7ZZ-6529711-D.*NOTE* Air conditioning cars...
Availability: Used / Wrecking Yard Item
Item #: 23478 -
Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar coupe or Ford Mustang coupe. This item will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Mustang hardtop glass only, convertible is different.Ford part # C7ZZ-6521410-C. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X...
Availability: Used / Wrecking Yard Item
Item #: 11166 -
Used passenger side (right hand) grade "A" tinted door glass for the Mercury Cougar coupe or the Ford mustang coupe. This item will have the faint green tint and be marked SUN-X. This door window comes with surrounding affixed trim. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 11167 -
Used driver side (left hand) grade "A" tinted door glass for the Mercury Cougar or Ford Mustang Coupe. This item will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. This door window comes with surrounding stainless steel affixed trim in good condition....
Availability: Ships Direct from Supplier (Except International)
Item #: 10180 -
New 1967 -1968 Cougar Mustang Passengers side Door Glass Green-tinted Note: Removing and reinstalling the frame from your glass to this reproduction can be a substantial job. you might consider purchasing our used version as it includes the frame at no additional cost. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original...
Availability: Ships Direct from Supplier (Except International)
Item #: 10181 -
Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang. This unit does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted...
Availability: Ships Direct from Supplier (Except International)
Item #: 27057 -
New driver side (left hand) clear door glass for the Mercury Cougar coupe or the Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version is...
Availability: Ships Direct from Supplier (Except International)
Item #: 27058 -
New passenger side (right hand) clear door glass for the Mercury Cougar coupe or the Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked version...
Availability: Ships Direct from Supplier (Except International)
Item #: 13625 -
Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...
Availability: Ships Direct from Supplier (Except International)
Item #: 13626 -
Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...
Availability: In-Stock Item
Item #: 30254 -
Bolt with toothed washer for attaching 1967-68 Mercury Cougar and Ford Mustang door window parts. Both of the door window rear stops, and rear door guide. 1/4-20 bolt threads.
Availability: Ships Direct from Supplier (Except International)
Item #: 15514 -
Reproduction six piece clear glass set for your Mercury Cougar. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...
Availability: Ships Direct from Supplier (Except International)
Item #: 19065 -
Reproduction clear seven piece glass set for the Mercury Cougar. This set consists of a clear driver side (left hand) and passenger side (right hand) vent / wing window, a driver and passenger side clear door glass, a driver and passenger side clear quarter glass, and a clear rear glass.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on...
Availability: Ships Direct from Supplier (Except International)
Item #: 15515 -
Reproduction seven piece tint glass set for the Mercury Cougar. This set does not come with any window trim so save your for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the...
Availability: Ships Direct from Supplier (Except International)
Item #: 23459 -
Reproduction six piece tinted glass set for the Mercury Cougar. This set does not come with any window trim so save your for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is this tinted version that will have a slight green tint to the glass, other wise know as Sun-X Tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...
Availability: In-Stock Item
Item #: 19971 -
Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.
Availability: In-Stock Item
Item #: 11779 -
This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00" Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...
Availability: In-Stock Item
Item #: 26688 -
These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging. Linear springs are the easiest to understand. When you think of a spring,...
Availability: In-Stock Item
Item #: 26654 -
Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.
Availability: In-Stock Item
Item #: 26562 -
This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.
Availability: In-Stock Item
Item #: 26571 -
This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.
Availability: In-Stock Item
Item #: 26596 -
Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.
Availability: In-Stock Item
Item #: 26561 -
Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Replaces Ford part #: C6OZ-3020-A.
Availability: Used / Wrecking Yard Item
Item #: 24273 -
C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.
Availability: Used / Wrecking Yard Item
Item #: 26866 -
Used taillight wiring harness repair plug and pigtail to the passenger side (right hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...
Availability: Used / Wrecking Yard Item
Item #: 26871 -
Used taillight wiring harness repair plug and pigtail to the driver side (left hand) inboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...
Availability: Used / Wrecking Yard Item
Item #: 26870 -
Used taillight wiring harness repair plug and pigtail to the driver side (left hand) center taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...
Availability: Used / Wrecking Yard Item
Item #: 26869 -
Used taillight wiring harness repair plug and pigtail to the driver side (left hand) outboard taillight for the Mercury Cougar. This is part of the 13A449 main taillight wiring harness. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...
Availability: Used / Wrecking Yard Item
Item #: 27537 -
Used 4 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for parking brake and low fuel indicators. Yellow and green light sockets. These are the same sockets for the parking brake and low fuel warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in you Cat? The video...
Availability: Used / Wrecking Yard Item
Item #: 27538 -
Used 3 pin connector and light socket harness for the 1967-68 Mercury Cougar overhead console harness for seat belts and door ajar indicators. Blue and red light sockets. These are the same sockets for the seat belt reminder and door ajar warning lights on the ultra rare Safety Convenience Option offered in 1967-68 on both the Cougar and Mustang.
Availability: In-Stock Item
Item #: 26928 -
Reproduction under hood wiring harness repair plugs and leads that go from the under hood harness to the starter solenoid on the Mercury Cougar or Ford Mustang. Sold as a pair.
Availability: Used / Wrecking Yard Item
Item #: 15772 -
Used taillight harness wiring repair pigtail from the K8 relay to the passenger side (right hand) door jamb for the 67 - 68 Mercury Cougar Standard / XR7
Availability: Used / Wrecking Yard Item
Item #: 15635 -
Used under dash wiring harness repair pigtail that goes from the engine feed harness to the neutral safety / backup lights of the Mercury Cougar Standard.
Availability: Used / Wrecking Yard Item
Item #: 11-0185 -
C7ZZ-65222A57-KIT Guide with hardware for the driver side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. Kit includes guide, attaching bolts, detachable stop, and special set screw and nut for angle adjustment. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel.
Check out our handy diagram below to find other '67-'68 door parts you may...
Availability: Used / Wrecking Yard Item
Item #: 11-0182 -
C7ZZ-65222A56-C Bare guide without hardware for the passenger side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to...
Availability: Used / Wrecking Yard Item
Item #: 11-0181 -
C7ZZ-65222A57-C Bare guide without hardware for the driver side door glass of all 1967-68 Mercury Cougar and Ford Mustangs. Sometimes called the slider, mounts to the door. *Installation hint - all of the dried crusty 40+ year old grease should be removed and fresh white grease should lavishly be coated in the channel. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...
Availability: Used / Wrecking Yard Item
Item #: 11-0223 -
373460-S Factory original used bolt used to fasten the guide to the door (2), and to hold the adjustable stop. Sold individually.
Availability: Used / Wrecking Yard Item
Item #: 11-0204 -
C7ZZ-222A54-A Door window rear stop, which installs to the guide (C7ZZ-65222A56/7). Stop adjusts the door glass in its up most position. One per door, fits right side. This piece falls down inside the door when the rear guide is removed. Bolt included, but may not be exactly as pictured. You can find the reproduction here. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to...
Availability: Used / Wrecking Yard Item
Item #: 11-0203 -
C7ZZ-222A55-A Door window rear stop, which installs to the guide (C7ZZ-65222A57). Stop adjusts the door glass in its up most position. One per door, fits left side. This piece falls down inside the door when the rear guide is removed. Bolt included, but may not be exactly as pictured. You can find the reproduction here. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...
Availability: Used / Wrecking Yard Item
Item #: 11-0205 -
C5ZZ-6521768-A Front bracket that mounts to the door window channel, it prevents the front section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side door. See C7ZZ-6521772-A for the rear stop bracket and bolt.
Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view...
Availability: Used / Wrecking Yard Item
Item #: 11-0206 -
C7ZZ-6521772-A Bracket that mounts to the door window channel, it prevents the rear section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and Ford Mustangs. Works on either the passenger or drivers side door. Casting # is C7ZB-21772-A See C7ZZ-222A54-A for the companion stop on the door guide. See C7ZZ-6521768-A for the front stop bracket and bolt. You can find the reproduction here. Check out our handy diagram below to find other '67-'68 door parts...
Availability: Used / Wrecking Yard Item
Item #: 11-0166 -
378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...
Availability: Used / Wrecking Yard Item
Item #: 11-0177 -
C7ZZ-6523288-A Steel slider mounts to the door window channel. Your door window regulator's two arms slide in this channel lifting or lowering the door glass. Works on either the passenger or drivers side doors of a 1967-68 Mercury Cougar or Ford Mustang. *Installation tip - Channel needs to be void of all old grease. For a smooth operation, replace with fresh lubricant for years of trouble free service.
Check out our handy diagram below to find other '67-'68 door parts you may need. All the...
Availability: Used / Wrecking Yard Item
Item #: 11-0170 -
C5AZ-6223230-A Steel bracket that mounts to the door of all 1967-68 Mercury Cougar and Ford Mustangs. This is the lower window regulator arm slider bracket. Comes with original mounting bolts. Works on either the passenger or drivers side door. *Installation tip - Channel needs to be void of all old grease. For a smooth operation, replace with fresh lubricant for years of trouble free service.
Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...
Availability: Used / Wrecking Yard Item
Item #: 11-0178 -
23318 This is the door window counterbalance spring that goes on the window regulator of a 1967-68 Mercury Cougar or Ford Mustang. Obsolete in the Master Parts Catalog, we only have a basic part number.
Availability: In-Stock Item
Item #: 19238 -
Very correct, quality regulator that is much better than the imports we see that are made of a softer metal. Replaces Ford Part # C8ZZ-6523201. *NOTE* The 1967 splined stud the window crank mounts to is taller on the 67 than the 68. They are not meant to interchange 67 to 68. If you install a 1967 regulator on your 1968 the window crank will not seat properly and will protrude from the door panel. If you try to install a 1968 regulator on a 1967 model the window crank will fit too tight to the...
Availability: In-Stock Item
Item #: 19283 -
Very correct, quality regulator that is much better than the imports we see that are made of a softer metal. Replaces Ford Part # C8ZZ-6523201. *NOTE* The 1967 splined stud the window crank mounts to is taller on the 67 than the 68. They are not meant to interchange 67 to 68. If you install a 1967 regulator on your 1968 the window crank will not seat properly and will protrude from the door panel. If you try to install a 1968 regulator on a 1967 model the window crank will fit too tight to the...
Availability: In-Stock Item
Item #: 13133 -
C7ZZ-652221-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.
Availability: Used / Wrecking Yard Item
Item #: 11-0239 -
C7ZZ-6521458-B Bare channel for mounting the right side or passenger door glass in a 1967-68 Mercury Cougar of Ford Mustang. We verify that the plastic rollers and plastic guide are in good, unbroken condition. Can also be found with part number C7ZZ-6521458-C. Regulator slide not included, see related items for the slides. Those are in short supply.
Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on...
Availability: Used / Wrecking Yard Item
Item #: 11-0249 -
C7ZZ-6521459-B Bare channel for mounting the left side or driver door glass in a 1967-68 Mercury Cougar of Ford Mustang. We verify that the plastic rollers and plastic guide are in good, unbroken condition. Regulator slide not included, see related items for the slides. Those are in short supply. Can also be found with part number C7ZZ-6521459-C. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search...
Availability: Used / Wrecking Yard Item
Item #: 11-0237 -
C7ZZ-652220-B Stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.
Availability: Used / Wrecking Yard Item
Item #: 11-0248 -
C7ZZ-652221-B Stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Driver side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind.
*Note - Excludes Mustang fastback and convertible.
Availability: Used / Wrecking Yard Item
Item #: 11-0425 -
Special bolt with large square captured washer. This one is shorter of the two that install in the vent window frame. This bolt has a 1/2" hex head with and has about 7/8" of threads with a dog point. See your shop manual for actual procedure. See also 378696-S for the vent window and front door channel set screws. Ford part number 379384-S2.
Availability: Out of Stock
Item #: 11-0426 -
Special bolt with large square captured washer. This one is longer of the two that install in the vent window frame. This bolt has a 1/2" hex head with and has about 1-7/8" of threads with a dog point. See your shop manual for actual procedure. See also 378696-S for the vent window and front door channel set screws. Ford part number 378694-S.
Availability: Used / Wrecking Yard Item
Item #: 11-0427 -
Special nut with large diameter spinning washer for the set screw for the door glass adjustment. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure. See also 378696-S for the vent window and front door channel set screws. Ford part number 33797-S.
Availability: In-Stock Item
Item #: 31207 -
Reproduction front bracket that mounts to the door window channel, it prevents the front section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side door. Replaces Ford part number C5ZZ-6521768-A
Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: In-Stock Item
Item #: 31325 -
Reproduction C7ZZ-222A54-A Door window rear stop, which installs to the guide (C7ZZ-65222A56/7). Stop adjusts the door glass in its up most position. One per door, fits right side. This piece falls down inside the door when the rear guide is removed. Bolt included.
Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video below: Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in...
Availability: In-Stock Item
Item #: 31326 -
Reproduction C7ZZ-222A55-A Door window rear stop, which installs to the guide (C7ZZ-65222A57). Stop adjusts the door glass in its up most position. One per door, fits left side. This piece falls down inside the door when the rear guide is removed. Bolt included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: In-Stock Item
Item #: 31327 -
Reproduction C7ZZ-6521772-A Bracket that mounts to the door window channel, it prevents the rear section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and Ford Mustangs. Works on either the passenger or driver side door. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18891 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18892 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great, look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18893 -
Upholstery components have an ETA of 5 - 9 weeks.
We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials. Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18894 -
Upholstery components have an ETA of 5 - 9 weeks. We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials. *NOTE* This product will take 4 – 6 weeks for delivery.
Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18895 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great, look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: Special Order, Ships Direct from Supplier
Item #: 18896 -
Upholstery components have an ETA of 5 - 9 weeks.We are proud to be amongst the only vendors around to offer this very rare bench seat interior kit. The pictures speak for themselves, these kits fit great look great and made of top quality materials.*NOTE* This product will take 4 – 6 weeks for delivery.Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 11801 -
These are great for your back seat belts or convertibles that did not use retractors in the front. They are an exact copy of the originals that were available as a dealer option from 1964 and up. Sold Individually. Made in U.S.A. Replaces Ford Part #: C4AZ-65611A06. Customer feedback: I just wanted to tell that your delivery has arrived today. Thanks a lot! Never ever ordered something (not even here in Germany) and got it that fast. Awesome! My next orders will go to your place and I will...
Availability: In-Stock Item
Item #: 41825 -
Includes one lap belt, the mounting bolts and washers.sold individually
Availability: In-Stock Item
Item #: 41826 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually
Availability: In-Stock Item
Item #: 41828 -
Great looking replacement style seat belt. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. These are great lap belts for convertible cars that don't use retractors. We suggest using seat belt anchor bolts for an easy installation of these aftermarket lap seat belts. This kit does come with installation hardware, but the threads on the bolt are coarse, and will not bolt into your original threaded anchor points. sold individually ...
Availability: In-Stock Item
Item #: 41895 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually
Availability: In-Stock Item
Item #: 41833 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41829 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41822 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41823 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 41832 -
Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually
Availability: In-Stock Item
Item #: 13711 -
These are era-correct looking seat belts at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers
Availability: In-Stock Item
Item #: 13708 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13706 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13710 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13715 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: In-Stock Item
Item #: 13714 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually
Availability: In-Stock Item
Item #: 13712 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! sold individually
Availability: In-Stock Item
Item #: 13707 -
This is an original looking seat belt at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! SOLD INDIVIDUALLY
Availability: In-Stock Item
Item #: 13709 -
These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually
Availability: Used / Wrecking Yard Item
Item #: 14-1011 -
Both deluxe and standard used the same retractor in 1968 - 1969 and left is the same design as right. Grade "B" retractors will be 100% functional but cosmetically will show a crack in the plastic holster, and may have minor rust on chrome. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-1014 -
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original starburst decal, which will be faded and need replacing. Find the replacement decals here. Spring is included.
Availability: Used / Wrecking Yard Item
Item #: 14-1012 -
Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-0000 -
This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...
Availability: Used / Wrecking Yard Item
Item #: 14-0100 -
This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...
Availability: Used / Wrecking Yard Item
Item #: 14-0110 -
Used seat belt buckle bezel for the Mercury Cougar, Ford Mustang, or Ford Torino. This is the outer portion of the two piece seat belt buckle cover. This is a good replacement part if you want to keep your car original. These bezels will be free of cracks and breaks. Please specify which color you're looking for when ordering. Keep in mind that there are only a handful of colored buckles available, so we'll do our best to get you the color you need. Check out our video "All about seat belts"...
Availability: Used / Wrecking Yard Item
Item #: 14-5001 -
This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...
Availability: Used / Wrecking Yard Item
Item #: 14-0073 -
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.
Availability: Used / Wrecking Yard Item
Item #: 14-0063 -
Hard to find without being faded, frayed or rusted buckle. Rarely, if ever will our used shoulder belts look this pristine as they are prone to sun fade. Sold individually, 2 required per car, hardware sold separate. Contact us for colors other than black. Check out our video "All about seat belts" below. ...
Availability: Used / Wrecking Yard Item
Item #: 14-0021 -
When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...