All Available Parts - 1968 Mercury Cougar

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown...

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits driver side doors of 1968 Mercury Cougar and Ford Mustang. 1968 door latches are unique, they have a longer tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

Pressure die cast in zinc and heavily chrome plated. Excellent quality. Drive pins and washers included, sold as a pair.

C8AB-7630323-A Usually these will not have knobs. Plan on purchasing new knobs. Ask about our B grade knobs that will have some pitting or lusting issues. This is the correct "shorty" crank for a 1968 Cougar front window crank. It is the same length as the rear 1968 - 1970 but uses a center screw instead of a side Allen set screw. The 1969 - 1970 crank (with AM or no radio) looks the same but is longer. These shorter cranks were also used in conjunction with the factory door speakers used in...

This is a good used original rear window crank with no obvious scratches or pitting. May or may not come with random colored knob. It most likely will be missing the decal but will have the original set screw. Ford part number is C8ZZ-6530322-A, casting number shown on back is C8ZB-6530323-A. Black knobs are the most commonly ones requested, plan on buying new knobs if you need black.

Best quality of the three version made and the only one that comes with the decal installed. This is held on by an Allen set screw, we often get calls from people who cannot figure out how to remove these. Check our good used cranks if you like to keep original FoMoCo parts on your Cougar. Replaces Ford part number C8ZZ-6530322-A.

This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Does not look or feel much like the original. Not really a stock color, fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Driver quality used right side or passenger side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

Used original door latch rod for the interior push button lock on the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521852-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968.  The casting number on the back reads C7AB-5422617-A.

These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968. The casting number on the back reads C7AB-5422616-A.

These pressure cast and chrome plated handles are good quality items that are exceptionally low priced. Not show quality or concours correct, but nice replacement. Includes gaskets and hardware. Replaces Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A Also Fits: 1967 Ford Mustang 1968 Ford Mustang 1970 Ford Maverick 1971 Ford Maverick 1972 Ford Maverick 1973 Ford Maverick

Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Emergency or parking brake indicator lamp and wiring harness. Tested and working red indicator light which was found optionally on any 1968 Mercury Cougar standard model 65A or 65C. The 1968 parking brake light kit gets its power from the ignition switch. 

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. We do offer the correct used Cougar horns.Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B...

Tested and working used Hi tone horn. The High tone is indicated in raised letters located on the perimeter of the horn. 1967-68 Cougars used part number C7WF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.NOTE* - High tone horn is on the passenger side ...

Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.

PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation. Our used 390 transfer tubes will often times have a dent or ding in the metal tube. The repro is a very top quality alternative, they would be concours correct in appearance.  ...

PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation.

100% Concours Correct PCV Tube for the 1968 Mercury Cougar 427 GT-E, Ford Mustang, Fairlane, or Torino with the 428 Police Interceptor, fits either # C6AE or # C7AE Aluminum PI intake manifold. Replaces Ford Part #: C6AZ-6758-B.

PCV tube for the Mercury Cougar, Ford Mustang GT500KR and Torino with the 428 CobraJet and Super CobraJet for 1968-69 and C8OZ-9424-C factory iron intake manifold. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 428 tube has a less pronounced angle, this is due to the taller 428CJ intake manifold. A less pronounced angle fits more closely to the passenger side valve cover. Replaces Ford Part #: C8OZ-6758-B.

This fitting screws into intake manifold, has 1/2" nipple for PCV hose, 3/16" vacuum port nipple and threaded hole for smaller accessory fitting. 5/8 by 20 thread pitch

Steel fitting for 390-4V / 427-4V and 428CJ engines with the PCV transfer tube.Replaces C7AZ-9A474-A. Painted Ford Corporate Blue from the factory.

Front steel vacuum fitting for 390, 427, 428CJ engines.Replaces Ford part number C7AZ-9A474-A.

Used brass intake manifold fitting that screws into the rear of the 390GT and 428 CJ intake manifold on all 1967-68 cars so equipped. Similar to the 1969 version, but this one does not have the additional smaller nipple.Replaces Ford part number C8OZ-9A474-A.

Designed for any one-inch hose, this clamp can be used for a number of different applications including the breather hose between the valve cover and air cleaner on 1967, and 1968 Cougars.

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Replaces Ford part #C7AZ-6892. For round hole with two notches, aluminum or steel valve covers.

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

C8OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1968 X code 390-2V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with an original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake manifolds, valve...

Reproduction positive crankcase ventilation valve or PCV valve for 1968 Mercury Cougar, Cyclone, Ford Mustang and Torino all with 390GT or S code 390-4V engines. Additionally this fits all 428 Cobra Jet and Super Cobra Jet engines 1968-1/2-1970. This valve has a stamped casting number of C8OE-6A666-B, comes with a white plastic ring as shown. Ford engineering number C8OZ-6A666-B. Also used on 1967 Shelby Mustang GT500, Ford 428PI, and Mercury Cougar GT-E 427-4V engines. *Note - Must be used...

Used brass fitting found on intake manifolds 1968-69 Mercury Cougar and Ford Mustang. Usually works with an adapter that screws into the rear of the intake manifold directly. With 3 vacuum ports for various accessories and a threaded port for the hard line going to the brake booster.  Replaces Ford part number C8AZ-9A474-B.

Reproduction hose that connects the oil cap to the air cleaner on cars equipped with the 289 engine. Replaces Ford Part number C6AZ-6A664-P

Rear steel vacuum fitting for 289, 302, and 351W engines. Various applications, this one has a single port for vacuum, and a threaded top section for either a plug or additional brass fitting. See other fittings for two and four port fittings in this style of steel intake manifold fitting for 1968-69 Mercury and Ford. Replaces basic Ford part number 9A474.

Rear steel vacuum fitting for 289, 302, and 351W engines. Various applications, this one has a two ports for vacuum, and a threaded top section for either a plug or additional brass fitting. See other fittings for one and four port fittings in this style of steel intake manifold fitting for 1968-69 Mercury and Ford. Replaces basic Ford part number 9A474.

Rear steel vacuum fitting for 289, 302, and 351W engines. Various applications, this one has a four ports for vacuum, and a threaded top section for either a plug or additional brass fitting. See other fittings for one and two port fittings in this style of steel intake manifold fitting for 1968-69 Mercury and Ford. Replaces basic Ford part number 9A474.

Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.

Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8

Used automatic floor shift bezel for all 1967-68 Mercury Cougar with automatic transmissions without factory consoles. Grade B will have some pitting and or scratches in the chrome. The rubber piece where the shift lever comes out will also be torn.  Check out this video

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

Reproduction, nice thick firewall insulation pad for the Mercury Cougar or Ford Mustang. We actually like this one better than the "premium" version. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are the same piece and will fit both A/C and non A/C cars.This pad comes with all the rubber clips needed for installation.

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

Easy to replace, keeps correct tension on your gas pedal.

Reproduction kick panel insulation for the 1967 - 1968 Mercury Cougar or Ford Mustang 

Kick panels for the 1967 and 1968 Mercury Cougar that include 6 1/2" coaxial (2 way) 100 watt speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. For some discussion on kick panel speaker options, check out this thread.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.*NOTE* These units may require some slight modification to fit perfectly in your unique Cat or Pony.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.

Kick panels for the 1967 and 1968 Mercury Cougar that are formed to accommodate speakers. Speakers are not included. These are designed for those who would like to choose their own speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. These now come pre-cut for a 5 1/4 inch speaker. For more discussion on kick panel speaker options, check out this thread.

Great way to update your sound system without cutting door panels or other original parts. Great fit and finish, easy installation. Pioneer speakers are 4ohms, 6 1/2" coaxial (2 way) 160 watts per speaker, for a total of 320 watts max output! Only available in black, but can be painted to match your interior with flexible paint. For more discussion on kick panel speaker options, check out this thread.

Sold as a pair, these are a perfect fit Premium Scott Drake reproduction. Correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers so if speaker holes are needed you will have to use your old panels as a template to drill holes in these "Mustang" reproductions. Replaces Ford Part number C7WY-650345-A1G / Casting number as seen on the back of the driver side will read C7WB-6502345-BW

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Reproduction interior kick panels in parchment / off-white for the Mercury Cougar or Ford Mustang. Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

"Premium" firewall pad for your 67 - 68 Cougar or Mustang. It's "premium" in the sense that it's more expensive. The main difference between this and the "economy" version is that it has a layer of foil inside, which helps with heat insulation. However, the total thickness is actually a little less than the economy version. This may make it easier to install, along with the included hard plastic clips (unlike the rubber originals). Given the significant difference in price for negligible...

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Good used core plastic bezel that has had one or more cracks or breaks. Finish will be poor or non existent. Ford part number: C8WF-10841

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent. Check out our video on dash removal and restoration:

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the HiBeam indicator bulb. One of the  holes is not used. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the right turn and seat belt indicator bulbs. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. Similar to the left turn shroud, there is a locating nub that makes it different. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the left turn and brake system indicator bulbs. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. Similar to the right turn shroud, there is a locating nub that makes it different. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the wiper switch. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. This baffle has a blacked out cone as shown. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the OIL light which is the left red light in the FUEL/TEMP gauge. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. This baffle is side specific, but resembles the AMPS baffle. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the AMPS light which is the right red light in the FUEL/TEMP gauge. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. This baffle is side specific, but resembles the OIL baffle. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 XR7 Model Mercury Cougar. This is for the Brake system indicator bulb. There are a total of 1 of these plastic baffles for a 1967-68 XR7 Model Cougar, and it goes into the XR7 housing and shares space with the tachometer. Originally, these had a rubber seal on the lip. No more seals. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with a Standard Model dash cluster. ...

Top bracket that attaches dash pad to driver side instrument cluster for all 1967-68 Mercury Cougars. Standard and XR7 models. Normally bare or zinc coated steel. This is a needed plate, it reinforces the top of the plastic of the instrument cluster and provides some strength when attaching the dash pad. Ford part number C7WY-10C899.

Warning lens indicating "BRAKES", attaches to the tachometer on any 1967-68 Mercury Cougar XR7. This is a red back lit lens, it tapes onto the back side of the tachometer bezel. Ford part number 10A936

Used metal dash support brace for all 1967-68 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 8-1/2 inches long. Viewed in the 1967 Osborn Body Assembly Manual on page 23. Replaces Ford part numbers C7ZB-6504672 or C7ZZ-6504672-A.

Used ashtray for the 1968 Mercury Cougar or Ford Mustang. This unit will come as taken from a Western parts car. Original FoMoCo construction, built to last. There is a slight difference between the 1967 and 1968 dash openings for these ashtrays. This 1968 ashtray painted face, measures 6-13/16 inches long. The 1967 version is 7-1/8 inches long measured with a flexible ruler.Ford part # C8ZB-6504810.

Used cigar / cigarette lighter and ashtray mounting bracket. Mounts behind the dash on 1967-68 Mercury Cougar and Ford Mustang. Holds the cigar or cigarette lighter element, and the ashtray receptacle. 

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...

Note: Not for use with aftermarket radios. Finding correct radio knobs for a 1968 Ford Mustang or Mercury Cougar equipped with a center console has been a huge obstacle for decades now. To clear the padded radio bezel cover, one must have these elusive, one year only, deep well knobs. These will also work on 1967 Cougar with console and although they would not be letter correct for anything but a 68 with a console, they do not look out of place on a 67 with console. Note that this four piece...

Reproduction inner radio knob used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This set of reproduction used knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out this video Still have riv-nut questions? Here are riv-nut answers! ...

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

New template to make your own package tray cover for the Mercury Cougar. Package trays are difficult to package and can be costly to ship.  This template will assist you in making your own. *NOTE* There is a slight difference in size between 1967 and 1968 package trays.