Exterior Lights

Good used pair of taillights that includes two average grade "B" bezels and two used grade "B" lenses with backing plates. No obvious cracks in the lenses but there will be stress cracks that will only be found under close inspection. The bezels will have good chrome with no obvious defects but the paint will need attention. This is a good saving over buying the four or six parts individually. Don't forget to pick up a set of gaskets for the lenses as they always are needed after 40 plus...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13441-AA

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13440-AA

1967 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated P83 in the wiring diagram. This plug plugs into the stop lamp relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable...

This oddball sequential unit was only used from 2/1/1971 to 5/15/1971 and will be of no interest except for to select few. The differentiating factor is the hard plastic connectors. We can supply a reproduction of this unit but it requires that you send your old unit to to us so we can reuse the plugs. Ford part # D1WY-13A366-C. 1971 Cougars built from 2/1/71 to 5/15/71 used a unique sequential system in the trunk, D1WY-13A366-C. It uses two connectors, grey and light blue, that are no longer...

This grade "A" taillight harness will be a rare uncut beauty with nice looking plug ends and wiring. This unit is for Mercury Cougars built prior to 1-3-67 with the stop lamp relay positioned next to the sequential unit in the trunk as opposed to under dash found on models made after 1-2-67. XR7 and Standard Cougars use the same rear wiring harness to the taillights. *NOTE* The stand out identifier of the early vs. late rear harness is the flat four prong plug with a red, two green and one...

This grade "B" taillight harness will have one or two professional repairs with unmelted plug ends. This unit is for Mercury Cougars built prior to 1-3-67 with the stop lamp relay positioned next to the sequential unit in the trunk as opposed to under dash found on models made after 1-2-67. XR7 and Standard Cougars use the same rear wiring harness to the taillights. *NOTE* The stand out identifier of the early vs. late rear harness is the flat four prong plug with a red, two green and one...

This grade "A" taillight wiring harness is a good used harness with no cuts or splices. Not for use with XR7 or Eliminator. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

This grade "A" taillight harness is a good used harness with no cuts or splices. Not for use with XR7 or Eliminator models. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

This grade "B" taillight wiring harness is a good used harness that may have one or two professional repairs and the plug ends will be nice and unmelted. Not for use with XR7 or Eliminator. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is...

This grade "B" taillight harness is a good used harness that may have one or two professional repairs. Not for use with XR7 or Eliminator models. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "A" premium grade harness that is not sun damaged, spliced, or damaged in anyway. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses...

Used grade "A" taillight wiring harness for the Mercury Cougar XR7. This will be a rare uncut beauty with clean unmelted, non corroded plug ends. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used grade "B" used harness that may have one or two professional repairs. Correct for XR7, Eliminator, and 1969-70 Shelby Mustang GT-350 and GT-500. Ford part # C9WY-14405-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...

Used grade "B" taillight wiring harness for the Mercury Cougar XR7. This unit may have one or two professional repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.