All Available Parts - 1967 Mercury Cougar

F7TBM or F7TBG We have found both numbers on these identical 1967 AM/FM radios. The ink stamped dates indicate that the F7TBM was used at the beginning of the model year. Very rare option as most rural communities did not even have a FM station in 1967. In 1967 this was not a true 'stereo' sound, still considered 'mono' sound. 1967 AM/FM radios are identified with having 5 chromed push buttons. This has been tested and and does not function properly. Unknown reason why it does not work. Good...

AM/FM RDS tuner with 25 presetsLCD display shows song / artist300 watts peak 2-Ohm stable7 LCD color choicesDimmer controlClock or function displayBluetooth and remote microphone includedUSB portDirect CD-I controlFront and rear auxiliary inputAlpha numeric display for MP3 / WMA / FLAC / WAVElectronic tuning and volume control and last volume memoryBass, mid, treble and tone controlloudness compensation for low volume listeningDSP EQFront / rear faderLeft / right balanceDigital clockHi volt 4...

Turnaround time is currently 6-7 weeks. This ingenious conversion lets you enjoy the best of both worlds - perfect original looks with uncompromised modern functionality. No more hiding a second head unit in the glovebox or settling for a "retro" radio that doesn't quite look right. The guts of this original Philco AM radio have all been swapped out and upgraded to the best modern electronics. All the added controls and adjustments are achieved by various clever twists of the knobs, as...

This used bezel is covered almost entirely by the face pad with clock. Only the small area around the radio actually shows once installed. This early bezel has the upper support, the later version is open. Keep in mind we have bezels that have been altered for an after market radio for substantially less money. Ford casting number C7WB-6504567-B  68102-171 Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling. All 67-68 standard consoles had a...

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

These anti static devices were installed under the front bearing dust caps on cars equipped with factory installed AM-FM radios. The part pictured is NOS, the one we currently have in stock is used. Sold individually.

Hard to find little detail item that is often times missing. Correct for Ford Mustang as well. According to the 1968 Cougar Electrical Assembly Manual on page #57, the cowl ground strap is called the "Strap Radio Receiver Hood Bonding." Ford part # C5AA-18870-A, the screw carries a part # of 380923.

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common after-market speakers in multiple depths. For more discussion on kick panel speaker options, check out this thread. If you only are looking to buy one, please call, we often times have an odd number in...

Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work.

C6OA-18832-A is the number stamped into the end of the Autolite capacitor. Attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. Application all Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory.. Starting in 1972 there is a Motorcraft version...

Correct plug for your 1967 - 1973 Mercury Cougar or Ford Mustang. Often these have been cut from the main loom to install an after market radio.

Reproduction radio plug and pigtail for your 1967 - 1971 Mercury Cougar or Ford Mustangs.

Correct plug for your 67-71 AM- FM radio, or 8-track... Often these have been cut from the main loom to install an after market radio.The 1972 model used the same plug, but the wires are not in the same spots, go figure! These are speaker wires not power wires.The color codes are:  White right cowl speaker.   Orange left cowl speaker. Speaker blue / black ground. Power "not this listing." Blue / red stripe, radio light. Yellow / black stripe, power in for radio. ...

If after installing a new stereo system you experience unwanted motor whine or engine noise, check all grounds on radio, amp, etc. If you still have the noise, this filter may help.Instructions included.

Very good reproduction of the speaker grille located on the package tray in the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. Includes the mounting hardware.  Sold individually.

6x9 Replacement for OEM package tray speaker. Comes pre-wired with the stock style pigtail to plug in to your original wiring. Sold individually, 2 required per car.

Kit includes one pair of 25 watt speakers (50 watts total peak) with correct pigtails and one pair of correct speaker grills with the exact screen pattern as original. Correct mount spacing utilizes the factory holes in your package tray, hardware included. This kit is 100% correct for the 1967 or 1968, but will work on the 69 or 70 as well. The Cougar package trays for the 69 and 70 came perforated from the factory for speakers, so the grills are not necessary. Thanks for the plug Mark!: "My...

This plate allows you to install (2) 3 1/2" speakers of your choice in place of the (1) original factory speaker in the dash of your Cougar or Mustang. This is the same plate used on the Kenwood and Pioneer Dual Dash Speaker kits. Check out this video

This 25 watt Tri Axial design is a big improvement over the original whizzer cone design and is an exact fit. Sold individually, this is a 5" by 7" speaker commonly called a "football" speaker. 4 Ohm.  Replaces Ford part # C7AZ-18808-D. Check out this video

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Great way to get more speakers without cutting or modifying your car. This system utilizes the studs used for mounting your defroster ducts. Rather cumbersome to install and requires taking much of your dash apart. Check out this video

Features two 4 ohm 3 1/2" coaxial two way speakers. Huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with or without in-dash factory AC. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Quality Kenwood speakers that features two 40 watt 3 1/2" coaxial two way speakers. this unit is a huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with in-dash factory AC or not. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Original used AM radio speaker lead wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustangs with factory AM radios. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios

Original used AM radio power lead wiring harness pigtail for the 67 - 71 Mercury Cougar and Ford Mustangs with factory AM radios. This double male plugged wiring pigtail solders to the your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios.

Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.

Good used speaker for the 67 - 68 Cougar or same year Torino. This is the speaker that fits inside the speaker pods situated behind the kick panels. These speakers are tested and in good shape with no tears on the cones. Good for the Cougar enthusiast who wants to keep their car as close to original as possible. Sold individually.

Hard to find little detail item that is often times missing. Correct for Ford Mustang as well. According to the 1968 Cougar Electrical Assembly Manual on page #57, the cowl ground strap is called the "Strap Radio Receiver Hood Bonding." Ford part # C5AA-18870-A

These were installed behind the kick panels on 1967-68 Cougars & the 1968-69 Fairlane, Torino, Cobra and Cyclone equipped with a factory AM-FM or AM-8 track radio. Easy to install considering you have a built in template behind the kick panels that are easy to cut out. These will accept common aftermarket 5-1/4" speakers in multiple depths. Sold as a pair. For more discussion on kick panel speaker options, check out this thread. Replaces Ford Part number C8OA-19A067-A ...

Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work. New Old Stock switch. Ford part number C7AZ-18972-A and C7AA-18972-A on the wiring tag. NOS

Flexible high pressure replacement brake hose for 1967 disc brakes with a 7/16 inch inlet that fits both passenger (right hand) and driver (left hand) sides of the Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Hose is 15" in lengthReplaces Ford part # C7OZ-2078-B.

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides of Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Replaces Ford part # C7ZZ-2078-A.

American made! Flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. Attaches to the rear end housing. 8 inch and 9 inch rear ends 1967-69 all with 28 splined rear axles.Replaces Ford part number C7ZZ-2282-A. *NOTE* Excludes 427, 428, and 1969 Boss 302 Eliminators.

Offshore Centric brand reproduction flexible high pressure replacement brake hose for the rear drum brakes on Mercury Cougar and Ford Mustang. Attaches to the rear end housing. Replaces Ford part # C7ZZ-2282-A. *NOTE* Excludes 427, 428, and 1969 Boss 302 Eliminators.

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Used front drum brake hose bracket for any 1967-70 Mercury Cougar or Ford Mustang. Simple bracket bolts to the front aprons and holds the brake hoses stationary. Right and left side are the same.Ford part number C1SS-2082-C.

Used bracket for mounting the rear axle flexible brake hose. This is a factory welded in bracket that was removed from a 1967-69 Mercury Cougar or Ford Mustang. Double check your placement for your particular year, when welding the bracket to your car. Good used bracket the you need to separate from the factory spot welds. Part bead blasted for photo, has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Ford part number C7ZZ-2A051-A.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits into a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2062-B or C9TZ-2062-B.

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with power drum brakes. These are brand new units, not rebuilt, and are made from high quality American made parts. WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

Reproduction brake pedal for the Mercury Cougar or Ford Mustang that is equipped with a manual transmission. This pedal is required when switching over to factory power brakes. NOTE: You can also use the automatic brake pedal by trimming down the pedal portion to the same size as the manual pedal.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with the manual transmission and drum brakes. This unique pedal is for use with the non-collapsible 1967 steering column and clutch pedal. This unit has a longer arm than drum brake pedals. The pedal is shipped bare, but the picture may show hardware and pedal pad with trim.Ford part # C7ZZ-2455-G.

Used drum brake pedal for the Mercury Cougar and Ford Mustang equipped with the automatic transmission. Unique shape to work in conjunction with the 1967 Cougar steering column and 4 wheel manual drum brakes. Pedal shipped bare, picture may show hardware and pedal pad with trim.Ford part # C7ZZ-2455-J.

These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1967 shaft uses a hairpin clip and washer on the end. We also sell the 1968-73 shaft, which uses a spring clip.Ford part number of C6AZ-2478-A.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

Bolt and nut for installation of disc brake pedals in any 1967-73 Mercury Cougar or Ford Mustang. See related items for plastic bushings and metal spacer.

Used passenger side (right hand) front drum backing plate for 2-1/4 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane /Torino equipped with the 289 or 302 engine. Typically when these cars were equipped with the small block V8 they came with 10" x 2-1/4" brakes shoes. Ford part # C3OZ-2012-B. *NOTE* Normally 6 cylinder Mustangs came with 9" x 2-1/4" drum brakes on the front.

Used driver side (left hand) front drum backing plate for 2-1/4 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino with the 289 or 302 engine. Typically when the car can with the small block V8 they came with 10" x 2-1/4" brakes shoes. Ford part # C3OZ-2013-B. *NOTE* Normally 6 cylinder Mustangs came with 9" x 2-1/4" drum brakes on the front.

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.

Reproduction interior turn signal indicator 53x light bulb for the Mercury Cougar. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Reproduction 97 License Plate Light Bulb for the 1967 - 1973 Mercury Cougar

Reproduction 158 Interior Auto Transmission Light Bulb for the 1967 and 1968 Mercury Cougar

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

These are also a good replacement bulb for the 67-68 under-dash courtesy lights as they are easier to grip than the 631 bulb.

Correct Backup Light Bulb for the 1967 - 1968 Mercury Cougar. Owners Manual and shop manual incorrectly state the backup light bulb to be the 1156.

Brand new 1157 (dual-filament) exterior stop lamp / turn signal light bulb for the Mercury Cougar or any vehicle equipped with 1157 bulbs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. For even brighter...

The 67 -73 Cougar uses the 1157A (Amber) bulb for the turn signals.  This bulb will also fit other applications that require an 1157A or 1157NA bulb. Replaces bulb #: 1157A or 1157NA

This bezel is covered almost entirely by the face pad with clock. Only the small area around the radio actually shows once installed. This late bezel does not have the upper support, the early version is closed. Keep in mind we have bezels that have been altered for an after market radio for substantially less money.Ford casting number C7WB-6504567-B 68102-171 Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling. All 67-68 standard consoles had a storage...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This bulb fits several applications including the door panel courtesy lights in the 1967 - 1968.

Reproduction 1893 Interior Radio Light Bulb for the 1967 - 1973 Mercury Cougar

New 1895 bulb for the instrument clusters. *Note - The table and the owners manuals are wrong for the Visual Check Panel bulbs, Ford literature calls out a 1895 bulb, when in fact the correct bulb is 1891.

Reproduction 4001 incandescent (non-halogen) high beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 2-prong plug and mounts in the inboard position on the car.These are OEM wattage (50 watts) to work with the factory headlight switch, without the need to add relays like you would for higher wattage halogen bulbs.Replaces bulb number 4001. Sold individually, 2 required per car.

The second image shows an original GE 212-1 bulb. These bulbs are no longer available, they have been superseded by bulb 212-2 (first picture).

"C" pillar courtesy light bulb which is also good for under under dash courtesy lights on 67 - 70 Cougars.

This unit is known as the "K5" relay in the service manual and is stamped with C7WB-13A366-B. The turn signal indicator relay switches the indicator light circuit so that the left indicator lamp on the instrument panel flashes for left turns and the right lamp flashes for right turns. Application is 1967 Mercury Cougar. No guarantee that replacing it with our used unit will actually make your dash lights consistently blink more than two or three times before going into a "pulsate mode" (if...

This is known as the "K6" relay in the Ford service manual, part number C7WB-10C838-C or C7WY-10B926-B. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps on 1967-68 Mercury Cougar during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. These relays are tested and working units. UNDER DASH RELAY *NOTE* This...

This is referred to as the "K7" relay in the Ford service manual. This relay causes the flashing action of the 1967 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C7WB-13A366-A, the Ford part number is C7WY-13A366-C. We have these relays tested and ready to ship. A quick bench testing: There needs to be continuity between the 'H' post and both 'B' and 'S' (separately). We test them with 12v to the 'H' post and the base grounded. 12volts should be read on...

1967 Mercury Cougar K-8 and K-9 turn signal relay assembly. K-8 for the passenger side, K-9 for the driver side turn signals. Also is integral to the brake light circuit. Clean used unit that is tested and will be functional. This unit will not be rusty, will not have internal water damage, may have minor repairs and no cut wires. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. Great for the...

Direct plug in solid state replacement, no modifications needed. We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

The function of this relay is to make only the center lights on each side illuminate when you activate the emergency warning flashers. Failure of this relay causes only the center sequential light to flash when using the turn signals. Trouble shooting these systems is takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. This unit is built into the 1967-68 Solid State Sequential Upgrade we sell so it is not needed if you are buying the all...

Reproduction 1892 Interior Exterior Light Bulb for the 1967 - 1973 Mercury Cougar

Replacement bulb for the door ajar warning light panel. This replacement bulb does not have the flashing feature like the OEM GE 256 installed bulbs. The original bulbs have a heat tab that flashes the bulb after a couple of seconds.

New 1891 bulb for the 1967-68 XR7 overhead console. This bulb will also fit the 67 - 68 rear console light. You can find the LED version of this bulb here.

Replaces stop lamp relay on 1967 Cougars built before 1-3-67. No wiring modifications needed, just plug it in in place of your old mechanical relay in the trunk. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the...

Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it mounts next to the sequential...

Tested, cleaned and working sequential turn signal motor for the mid 1967 and all 1968 Mercury Cougars. This is the dual plug motor compared to the single plug 1967 turn signal relay. Clean used unit that is tested and will be functional. This unit will not be rusty or have internal water damage, may have minor repairs, no cut wires. Trouble shooting these systems takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. We suggest you consider our...

At last, there's a solution to a problem that almost all early Cougars suffer from. If the turn signal indicators in your dash only blink once, and then pulsate slowly without going out, you need this new electronic relay. It's a direct plug-and-play replacement, and it will give your indicators a nice on-off flash, complete with a mechanical click sound, all in time with your turn signals. We're excited about this simple fix, it's great to see and hear the indicators working properly. The...

Tested and working sequential turn signal motor for the mid 1967 and all 1968 Mercury Cougars. This is the dual plug motor compared to the single plug 1967 turn signal relay. New in box (Motorcraft box) unit that is tested and will be functional. Trouble shooting these systems takes time. A single bad ground at any portion of the turn signal circuit can cause no end to problems. We suggest you consider our all inclusive solid state unit that replaces all the units in the trunk if you have...

New Old Stock relay. Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This turn signal switch for the 1967 Cougar equipped with the tilt / tilt away steering column is made using the original tooling acquired from the original manufacture of this part that Ford purchased these switches from when they were originally installed new in the Cougar. If you have replaced your sequential unit in the trunk with one of our new solid state sequential...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

These are all new, not rebuilt, concours quality. Features authentic markings and logo. Black only, no other colors available. Replaces Ford part # C6AZ-11450-A. *NOTE* There are dozens of styles which were produced by several manufacturers. These parts represent the most common type.

These are all new, not rebuilt, OEM Ford quality. We recommend these over the generic version and the "concours" version. Marked with Ford D2AF-11450-AA part number, but is functionally correct for all 1967-73 Cougars. Black case as original.Replaces Ford Part #: C7AF-11450-A1 , B6AZ-11450-A , C7AZ-11450-A , D2AF-11450-A , etc