All Available Parts - 1973 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 801-900 of 2233
Sorted By:
Availability:
Display Options:
Availability: Used / Wrecking Yard Item
Item #: 32286 -
D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.
Availability: In-Stock Item
Item #: 11034 -
Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.
Availability: In-Stock Item
Item #: 11033 -
Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.
Availability: Used / Wrecking Yard Item
Item #: 19812 -
Contains nut, lock washer, and spacer. Fits all Ford alternators.
Availability: Used / Wrecking Yard Item
Item #: 19813 -
[No Description Provided]
Availability: Used / Wrecking Yard Item
Item #: 19814 -
[No Description Provided]
Availability: Rare / NOS Part
Item #: 13892 -
This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...
Availability: Used / Wrecking Yard Item
Item #: 13601 -
Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...
Availability: Used / Wrecking Yard Item
Item #: 16122 -
Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...
Availability: Out of Stock
Item #: 25397 -
D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.
Availability: In-Stock Item
Item #: 32341 -
Contains nut and washer. Fits all Ford alternators. AMK F-644.
Availability: In-Stock Item
Item #: 25879 -
Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.
Availability: In-Stock Item
Item #: 25880 -
Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.Here's our video on chassis and suspension upgrades:
Availability: Used / Wrecking Yard Item
Item #: 31218 -
Wiring harness segment to the convertible power top pump on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1ZB-15A668-AB.
Availability: Used / Wrecking Yard Item
Item #: 31219 -
Wiring harness segment from firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1WB-15A690-AA.
Availability: Used / Wrecking Yard Item
Item #: 31220 -
Wiring harness under hood segment from circuit breaker through the firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1ZB-15A669-A.
Availability: Out of Stock
Item #: 13614 -
Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.
Availability: In-Stock Item
Item #: 41397 -
Availability: In-Stock Item
Item #: 30536 -
Reproduction flexible duct end that was originally stapled to the passenger side fresh air duct, found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1ZA-18C305-AB.
Availability: In-Stock Item
Item #: 25937 -
This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...
Availability: Ships Direct from Supplier (Except International)
Item #: 14924 -
These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...
Availability: In-Stock Item
Item #: 12174 -
HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...
Availability: In-Stock Item
Item #: 11083 -
Nice lower quality ignition coil for those of you on a tighter budget. A wee bit cheaper than the other performance coils we offer like the Yellow Top Coil or the Pertronix Flamethrower series coils, but still a great buy and very reliable.
Availability: In-Stock Item
Item #: 21600 -
New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually. Replaces Ford part number 382929-S.
Availability: Used / Wrecking Yard Item
Item #: 30354 -
Used wiring harness that runs from the A/C switch to the reisistor harness. Harness plugs into the blower switch and runs to the resistor box and de-icing switch.For part number D3ZB-19C603
Availability: In-Stock Item
Item #: 30843 -
Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 31802 -
NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...
Availability: In-Stock Item
Item #: 13786 -
Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C
Availability: In-Stock Item
Item #: 13784 -
Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339
Availability: In-Stock Item
Item #: 14103 -
Folks, this one just doesn't fit. Probably fits a 1973 or later 302 Ford, but not on the Cougar? The crankshaft center hole is 2-9/16 inches, the originals were just over 2 inches in diameter. Timing Cover not for 1967-1969 289/302/351W using a water pump with a backing plate. Features a cast-in timing pointer and dipstick hole.
Availability: Used / Wrecking Yard Item
Item #: 16197 -
Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...
Availability: Used / Wrecking Yard Item
Item #: 12929 -
Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.
Availability: Used / Wrecking Yard Item
Item #: 12971 -
Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in any 1973 Mercury Cougar or Ford Mustang. Technically, 1972 California 351C cars and 1973 351C cars used this timing pointer. Part stamped with casting number D2AE-6023-BA. The smaller more common version will also fit and look better in our opinion. Replaces Ford part D2AE-6023-BA.
Availability: In-Stock Item
Item #: 31985 -
Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown.
Availability: In-Stock Item
Item #: 31997 -
Brass and steel freeze plug or expansion plug set for any Ford 351C engine. 1970-74 Mercury Cougar and 1970-73 Ford Mustang. 12 piece set with threaded screw in plugs as shown.
Availability: Used / Wrecking Yard Item
Item #: 32091 -
Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.
Availability: Out of Stock
Item #: 32221 -
Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP
Availability: In-Stock Item
Item #: 32401 -
Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.
Availability: Used / Wrecking Yard Item
Item #: 33595 -
Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A.
Availability: In-Stock Item
Item #: 31137 -
Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.
Availability: In-Stock Item
Item #: 16238 -
Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...
Availability: In-Stock Item
Item #: 12341 -
Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.
Availability: In-Stock Item
Item #: 31135 -
Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.
Availability: In-Stock Item
Item #: 31134 -
Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe. Clamp only, Sold individually. This is a Scott Fuller reproduction.
Availability: In-Stock Item
Item #: 31136 -
Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford. Clamp only, Sold individually. This is a Scott Fuller reproduction.
Availability: In-Stock Item
Item #: 26818 -
Reproduction Upper Control Arm To Shock Tower bolt. Sold individually. Replaces Ford part # 38049-S
Availability: In-Stock Item
Item #: 53233 -
Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"
Availability: In-Stock Item
Item #: 12127 -
Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...
Availability: In-Stock Item
Item #: 30950 -
Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.
Availability: In-Stock Item
Item #: 11004 -
Complete 22 bolt set for oil pan on the 70 - 73 Cougar or Mustang.
Availability: In-Stock Item
Item #: 31239 -
Reproduction bolts and washers for the automatic transmission bell housing on any 1971 - 73 Cougar or Mustang equipped with a 351 engines and C-6 transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1971-73.
Availability: In-Stock Item
Item #: 31069 -
Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut.
Availability: Out of Stock
Item #: 32421 -
Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.
Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...
Availability: In-Stock Item
Item #: 32356 -
Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors.
Availability: In-Stock Item
Item #: 14-0026 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...
Availability: In-Stock Item
Item #: 14-0042 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...
Availability: Rare / NOS Part
Item #: 25821 -
This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.
Availability: Out of Stock
Item #: 25749 -
Availability: Rare / NOS Part
Item #: 25808 -
Availability: Rare / NOS Part
Item #: 32726 -
New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.
Availability: Out of Stock
Item #: 32733 -
NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.
Availability: Rare / NOS Part
Item #: 32741 -
NOS new old stock intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit. *NOTE* Must be used in conjunction with an intermittent wiper controller. Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.
Availability: Out of Stock
Item #: 32759 -
This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.
Availability: Out of Stock
Item #: 32762 -
New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury switch that turns the light on when the lid is raised and off when lowered. Replaces Ford accessory part #: C2RZ-15A700-A.
Availability: Out of Stock
Item #: 32763 -
New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...
Availability: Rare / NOS Part
Item #: 32775 -
New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description. Ford part number 382624-S100.
Availability: Rare / NOS Part
Item #: 32780 -
Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.
Availability: Rare / NOS Part
Item #: 19269 -
*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...
Availability: Rare / NOS Part
Item #: 32855 -
New old stock driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. Ford part number D1ZZ-6530147-A.
Availability: Rare / NOS Part
Item #: 32881 -
NOS distributor lead wire with green boot for the coil. Direct replacement for 1968-73 Ford distributors. There were several colors of boots that go to the coil, this is a green one as shown. Ford part number C7VY-12216-A.
Availability: Rare / NOS Part
Item #: 32882 -
NOS distributor ground wire. Direct replacement for 1967-73 Ford distributors. New old stock cable for inside the distributor, non ferrous metal, brass? Ford part number D2AZ-12264-A.
Availability: In-Stock Item
Item #: 14177 -
Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...
Availability: In-Stock Item
Item #: 19047 -
Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.
Availability: In-Stock Item
Item #: 26602 -
Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.
Availability: In-Stock Item
Item #: 26641 -
These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.
Availability: In-Stock Item
Item #: 26671 -
For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.
Availability: In-Stock Item
Item #: 26595 -
This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.
Availability: In-Stock Item
Item #: 26581 -
Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: In-Stock Item
Item #: 26584 -
Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...
Availability: In-Stock Item
Item #: 26672 -
Replaces Ford part #C7AZ-13568
Availability: In-Stock Item
Item #: 13940 -
These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.
Availability: In-Stock Item
Item #: 26678 -
Used to seal the Aluminum shifter housing to the transmission tunnel. Replaces Ford part #: C9ZZ-7370. Check out our video on rebuilding your shifter below: ...
Availability: In-Stock Item
Item #: 14248 -
We suggest using white lithium grease or petroleum jelly to ensure the seal will not stick to the shift lever. Fits 1969-73 Mercury Cougar and Ford Mustang, additionally it also fits 1971+ Maverick and Comet with floor shift automatic only. If you have any side-to-side play in the shifter, this seal will not last. We do have the shifter bushings available. Replaces Ford part numbers C9ZZ-7D351-A & D1ZZ-7D351-A. Get the matching mounting clips here. Check...
Availability: In-Stock Item
Item #: 26661 -
Sold as a PairReplaces Ford Part #: D1ZZ-6520264-A and D1ZZ-6520265-A.
Availability: In-Stock Item
Item #: 26658 -
These feature all the original details. Quality rubber molded around a steel insert.Replaces Ford Part #: D1ZZ-6528182-B and D1ZZ-6528183-B.
Availability: In-Stock Item
Item #: 26224 -
Reproduction firewall to hood seal or cowl seal for the Mercury Cougar or Ford Mustang. Comes with attaching clips. Replaces Ford part # D1ZZ-16740.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts always as advertised, and delivered timely.That impressed me then,...
Availability: In-Stock Item
Item #: 26591 -
Four per car, mounts to fenders. Replaces Ford part #D1ZZ-16758
Availability: In-Stock Item
Item #: 26669 -
Replaces Ford part #D1ZZ-17430.
Availability: In-Stock Item
Item #: 26677 -
Seal the steering column flange to the firewall. Used on cars with automatic transmission. Replaces Ford part # D1ZZ-3513
Availability: In-Stock Item
Item #: 26573 -
Sold in a set of three, includes attaching screws. Replaces part # 380478-S3
Availability: In-Stock Item
Item #: 26597 -
15 Piece kit that includes quarter panel drain plugs.
Availability: In-Stock Item
Item #: 26640 -
Sold individually, two required per car.
Replaces Ford Part #: 375838
Availability: In-Stock Item
Item #: 19966 -
These form a seal between your rear marker lights and the quarter panels. Replaces part # D1ZZ-15447. Sold as a pair.
Availability: In-Stock Item
Item #: 26478 -
Keep in mind not all gaskets are created equal... Many of these gaskets are made by two or three different makers. We have used these gaskets ourselves on our own Cougars with success, and know which ones fit correctly and which ones will stand the test of time. You may save a dollar or two buying elsewhere on some of these items but is it worth it? Ask the person selling the item if they personally have ever used the part. Replaces Ford part #D1ZZ-6542084. Installing the gasket yourself? you...
Availability: In-Stock Item
Item #: 41552 -
Reproduction clutch lever dust boot for the Mercury Cougar or Ford Mustang. This unit is used with the 429 in 1971 and in all Cougars and Mustangs in 1972 and 1973 equipped with manual transmissions and the 351 engine.Replaces Ford part #C5AZ-7513-A.
Availability: In-Stock Item
Item #: 26563 -
Mustang part that has incorrect thickness and a slightly different overall geometry to it. We also carry the correct Cougar version of this gasket, but only in used form.Replaces part # D1ZZ-18898.
Availability: In-Stock Item
Item #: 26234 -
Reproduction door glass to roof weatherstripping for your Mercury Cougar or Ford Mustang. An inexpensive way to better seal the interior space of your Cougar or Mustang.Replaces Ford part #'s D1ZZ-6551222-A and D1ZZ-65223-A.
Availability: In-Stock Item
Item #: 41005 -
These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Two required per car.Replaces Ford part # D1ZZ-6522244. Sold individually
Availability: In-Stock Item
Item #: 26633 -
Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.
Availability: In-Stock Item
Item #: 26682 -
Replaces Ford part # D1ZZ-9072. Special gas proof rubber seal that mounts in gas tank and filler pipe. Warning! If reproduction tank or filler pipe is not the same dimensions as originals the seal may leak, make sure and check for a good seal before putting into use.