All Available Parts - 1973 Mercury Cougar

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

Used jumper wire that connects the tilt-a-way door jamb and to the underdash harness.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Nice lower quality ignition coil for those of you on a tighter budget. A wee bit cheaper than the other performance coils we offer like the Yellow Top Coil or the Pertronix Flamethrower series coils, but still a great buy and very reliable.   

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

Replacement LED light that replaces the 212 bulb for the door courtesy lights on your 69 - 70, or the map lights on the 71 - 73 Cougar. These LED's give a fuller, brighter effect as compared to standard incandescent bulbs.

Used wiring harness that runs from the A/C switch to the reisistor harness. Harness plugs into the blower switch and runs to the resistor box and de-icing switch.For part number D3ZB-19C603

Used heater control light and socket assembly. Good for 71 - 73 Cougars with or without A/C.

Used rear window defog switch and knob assembly with mounting bracket for the 71 - 73 Standard Cougar.

Used heater control light wiring harness for the 72 - 73 Cougar with A/C.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in most 1970-72 Mercury Cougar or Ford anything including Mustang. Can be used on any 1970-74 351C engine from Ford. Technically, 1972 California 351C cars and 1973 351C cars used a different timing pointer for what ever reason. Replaces Ford part D0AZ-6023-A.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 351C in any 1973 Mercury Cougar or Ford Mustang. Technically, 1972 California 351C cars and 1973 351C cars used this timing pointer. Part stamped with casting number D2AE-6023-BA. The smaller more common version will also fit and look better in our opinion. Replaces Ford part D2AE-6023-BA.

Brass and steel freeze plug or expansion plug set for any Ford 351C engine. 1970-74 Mercury Cougar and 1970-73 Ford Mustang. 12 piece set with threaded screw in plugs as shown. 

Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

Used cover plate or thrust plate that retains the camshaft on the front of Ford V-8 engines such as 351C, 351M, 400, 429, 429CJ, and 460. 1970-76 Mercury Cougar or 1968-76 Ford anything. We have found a Ford number of C8SZ-6269-A. 

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

Complete 22 bolt set for oil pan on the 70 - 73 Cougar or Mustang.  

Reproduction bolts and washers for the automatic transmission bell housing on any 1971 - 73 Cougar or Mustang equipped with a 351 engines and C-6 transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1971-73.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Hardware kit for installing the fuel pump on 70 - 73 Cougar and Mustang equipped with the 351 Cleveland engine.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog. Shown in Black.Check out our video f the 2013 Open House event. See you next year! ...

This is cool... This Huge decal is almost 60" wide! Great for your enclosed trailer, garage door, wall or floor. This universally recognized logo says it all! Display it with pride. This item is free when you purchase $1000.00 or more at one time on this online catalog.Check out this video of our 2013 Open House event. See you next year! ...

Like working on your Cougar's engine? Keep your Cougar's fender from getting scratched with this Cougar fender cover.Check out this video of our 2013 Open House event!

Reproduction license plate frame for your Mercury Cougar.  Sold individually. Note: These will not clear on the rear pull down fuel door on the 1967- 1968, so they will only work for the front license plate on the 67-68 Cougar. These can be used for front or back on the 69-73 Cougar.Check out this video of our 2013 Open House event. Se you next year! ...

New Cougar Drive-In poster by WCCC! This 20" x 30" poster is printed on heavyweight matte archival paper and features a satin finish. Suitable for framing, this print would make a great decoration in your garage or living room. This photo was taken at our annual Open House event in 2013.Here's a video of our 2013 Open House event! ...

New large black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 21" X 9" X 9" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

Cougar poster by WCCC, featuring a 1969 XR7 Convertible against a stunning sunset and impressive skyline, this 20" x 30" poster is printed on heavyweight archival paper and features a semi-gloss finish. Suitable for framing, this print would make a great decoration in your garage or living room.  *NOTE - Please excuse the typo on our phone number at the bottom of the poster! The phone number on our business cards and at the bottom of our website is correct. ...

Over the years WCCC has supported many underprivileged individuals. And now through the help of one of our valued customers who is a retired corrections officer, we are offering these leather key fobs which were created and hand painted by inmates at the Oregon State Penitentiary. A great gift for any Cougar lover!  Measures 4" x 2-1/2"

This listing is for anyone who wants to order a custom set of floor mats. Simply add this item to your cart, and in the order notes section of your order, let us know which carpet color you want (please choose from the available options in color sample photo above or if ordering at the same time as a carpet kit simple say "please match ordered carpet color") and which script you would like, whether it be the Walking Cat, Cougar Head Logo, XR7, The Cougar Script or the GT...

These floor mats were available as part of the factory "protection package" or as a dealer accessory when these cars were new. Good used originals have gotten VERY hard to find. At present (9-20-18) they are only available in black. Keep in mind the 69-73 convertible used a narrower mat to clear the inner rockers. We have a diagram that shows you where to trim for your convertible. The walking Cougar logo is a favorite of any Cougar fan. The Cougar became so popular that soon after the Cougar...

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

NOS sequential unit for the taillights of the Mercury CougarFord part # D1WY-13A366-A.1971 Cougars built from 2/1/71 to 5/15/71 used a unique sequential system in the trunk, D1WY-13A366-C. It uses two connectors, grey and light blue, that are no longer serviced. When the sequential system must be serviced, it can be replaced by an NOS unit, or a replacement unit, such as the C9WY-13A366-AL sequencer shown below. Since these unique connectors are no longer available, the connector plugs on the...

D0AZ-6331604-A

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

C9ZZ-2454-A

NOS radio bezel for the 1971 - 1973 Mercury Cougar. 

New Old Stock 1973 Mercury Cougar driver side tail light bezel, NOS. Ford part number D3WY-13489-B.

New Old Stock 1973 Mercury Cougar Driver side, headlight door.  Casting number reads D3WB-13064. Ford part number D3WY-13064-B

New Old Stock 1973 Mercury Cougar Passenger side, headlight door.  Casting number reads D3WB-13052. Ford part number D3WY-13064-A

New Old Stock NOS passenger side front turn signal bezel for any 1973 Mercury Cougar.Ford part number  D3WY-13210-A, casting number D3WB-13236-AB.

New Old Stock NOS driver side front turn signal bezel for any 1973 Mercury Cougar. Ford part number  D3WY-13212-A, casting number D3WB-13237-AB.

NOS quarter script or emblem for any 1971-73 Mercury Cougar.  Ford casting number D1WB-16B114-A. MPC number D1WY-16098-A.

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

NOS drivers side (left hand) tail light lens for a 1973 Mercury Cougar. New old stock in the box Ford part, you know you want it! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something...

Driver side front turn signal and combination side marker lens. Clear color, fits 1973 Mercury Cougar all models. These are New Old Stock or NOS, but they will have shelf wear. Meaning light scratches or scuffs in the plastic. Using a product like Novus Plastic Polish really make these shine.Replaces Ford part number D3WY-13209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of...

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description.  Ford part number 382624-S100.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

New old stock driver side interior door handle for base Standard model 1971-73 Cougar, 1971-73 Ford Mustang and Maverick and Torino. Ford part number D1AZ-6522601-ANote - Does not fit most standard Cougars or all XR7's. Interior code has to start with a 1 or letter A.

New old stock passenger side interior door handle for base Standard model 1971-73 Cougar, 1971-73 Ford Mustang and Maverick and Torino. Ford part number D1AZ-6522600-A Note - Does not fit most standard Cougars or all XR7's. Interior code has to start with a 1 or letter A.

NOS inner, small moulding that attaches to the driver side vertical grille support. Fits any 1971, 1972, or 1973 Cougar. New old stock may show some scuffing from shelf wear. Note these are pot metal, and the plating was pretty thin from back in the day. We also have grade A and B and restored trim. See related items. Ford casting number D1WB-13B136-AC or D1WY-13A112-B.

New old stock driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. Ford part number D1ZZ-6530147-A.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, cable and hardware, NOS Ford. Detailed instructions included. Latch not included with this kit. Sorry, the way it came. This kit was a dealer sold kit or over the counter kit. Fits a large range of Ford cars. Ford part number C4AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to...

NOS ignition switch. 1973 version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. New Old Stock still has the white plastic pin installed, needs to be removed prior to installation. The pin prevents the plunger from moving around in storage. Ford part number D3AZ-11572-A. ...

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Replaces Ford part #: D2WY-6543720.

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Replaces Ford part #: D1ZZ-7653986. Seven piece kit with attaching hardware.

Replaces Ford part #D1ZZ-7602626

Replaces Ford Part # : D1ZZ-7651325-A

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...