All Available Parts - 1972 Mercury Cougar

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Driver side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1970-71 Mercury Cougar and Ford Mustang.

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1970-71 Mercury Cougar and Ford Mustang.

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1971-73 Mercury Cougar and Ford Mustang.

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For all 1972-73 Mercury Cougar or Ford Mustang with 43-55 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. For 1972-73 Mercury Cougar and Ford Mustang all with V-8 engines.Positive cable is 10 1/4" center to centerNegative cable is 42" center to centerGround wire is 41" center to center Replaces Ford Part # :...

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

Reproduction battery heatshield that fits many applications from 70-73, on most hi-performance engines. It was often the first part discarded but serves a real purpose.

NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars.  Replaces Ford Part #: D0OZ-10732-B.

Our excellent used sockets are a better price and better quality.This item does not come with a 194 bulb.

This used socket is found on the backside of your instrument cluster and takes a 194 bulb.

We cannot provide new units anymore but we do stand behind this used unit for 30 days.Check out the video below on our new gauge tester: ...

Replaces Ford Part # C9ZZ-10914

1971 - 1973 Mercury Cougar Ford Mustang rectangular clock found optionally in the center console. Used clocks generally do not work after 36 years. These are considered cores. We also offer clocks with modern quartz movements or NOS movements in restored clocks.Ford Part Number: D1ZZ-15000-C. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered...

Good Used Clock Harness for the 1971, 1972 or 1973 Mercury Cougar or Ford Mustang Mach 1. Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness, and ashtray light socket and shroud. The Mustang wiring harness for the clock generally does not include the light socket for the ashtray. The MPC indicates that the Mach 1 did receive this Cougar wiring harness. Ford part number: D1WY-15A006-A and D1WB-15A006-A.

Used Fuel Gauge for the XR7 1971 - 1973 Mercury CougarCheck out the video below on our new gauge tester:   ...

Good used gauge that is guaranteed to work.Check out the video below on our new gauge tester: ...

Good used tachometer for your 1971 - 1973 XR7 Cougar.Check out the video below on our new gauge tester: ...

Will include indicator light lenses.Check out the video below on our new gauge tester:

Will include indicator light lenses.Check out the video below on our new gauge tester:

Perfect condition with no burns, breaks and is not separating. Fits all 1971-73 Mercury Cougars, XR7 (65F & 76F) and Standard (65D & 76D) models.Check out the video below on our new gauge tester: ...

No cracks or deterioration from UV rays.

Good used unit with no cracks, only for the xr7.

Good Reproduction map light lens.Ford Part #: D1WY-13734-A.

Good used map light assembly. Ford Part #: D1WB-15650-AA or D1WY-15650-AA (Light Assembly) Also available with mounting hardware

New temperature sending unit for the 1970 - 1973 Mercury Cougar and Ford Mustang with an actual temperature gauge. Fits 351C and 351W engines. Temp Sender Switch Temp Rating : 22.7-25.5 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPTF Replaces Ford Part #: D0WY-10884-A (SW-924)Check out the video below on our new gauge tester: ...

New reproduction instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Features Solid State electronic circuitry. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator...

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

Used tested red lamp for the rear defog or heated back lite option for all 1971-73 Mercury Cougar and Ford Mustang with that factory option. These are tested, and the lights do work, there is a bulb sealed inside. According to the Ford MPC, this also was used on full sized Ford and Mercury cars.

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

C8OZ-14A068-GRADEB Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 71 72 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

C8OZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

D1ZZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness.72 73 Mercury Cougar Ford Mustang fuse panel. We suspect that this brown colored fuse block was used towards the end of 1972 and all of 1973. Identified by the brown color, and having a 20AMP fuse 'cigar lighter and horn' fuse location.

C8OZ-14A187-A Unique 1/4"-20 bolt for attaching the fuse blocks. 69 70 71 72 73 Mercury Cougar Ford Mustang fuse panel attaching bolt. Includes "C" clip and spring as shown. "C" clip keeps the bolt in the black fuse block.

D1ZZ-14A068-A GRADE B Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 72 73 Mercury Cougar Ford Mustang fuse panel. We suspect that this brown colored fuse block was used towards the end of 1972 and all of 1973. Identified by the brown color, and having a 20AMP fuse 'cigar lighter and horn' fuse location.

Key reminder and headlamp reminder buzzer for 1972-73 Mercury Cougar and Ford Mustang. Also used on Many other Ford, Mercury, and Lincoln vehicles in this time frame. Can also be stamped D2AB-13150-A1A D2AB-13150-A2A. Ford master part number D0AZ-13150-E. All buzzers are bench tested prior to shipping.

1969-1973 4 amp Buss style glass tube fuses sold individually and used for the instrument panel, clock, radio, heater control, and ashtray lights.

1969-1973 20 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for accessory feed, seat belt warning, tilt swing column, speed control, door ajar, low fuel, and power window relay.

1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.

The automatic seat back release option for 1971 to early 1972 (before December 1971) Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the 1971- early72 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, and cross over wiring. This option is best added to seats...

The automatic seat back release option for Mid 1972 (after December 1971) Mercury Cougar and Ford Mustang. The automatic seat back release would pull the release lever on both of the bucket seats. This only happens when the either the driver or passenger side door is opened. Kit comes with the mid 1972 specific wiring harnesses from the solenoid, includes 3 pin switch for the passenger pillar post, relay, solenoids, plug for retractable seat belts, and cross over wiring. This option is best...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

Vinyl dipped. Clip is used to hold wiring away from hot engine. Also found on trunk floor.

Tested and working 71 - 72 6000 RPM standard face tachometer with correct brake and oil indicator light windows. Ford part number D1WF-17360-F Shipping and Packaging Tips: Tape something over the face of the tachometer, or put them into a small container to protect the delicate needle. We normally use plastic sandwich containers that protect the face of the tachometer from coming into contact with packing materials or the cardboard box. Please make sure that the tachometers are packed so...

Good used Grade A unit that has never had the odometer tampered with. Check out the video below on our new gauge tester: ...

This one piece lens was used only on the XR7 model Cougar from 1971 - 1973. This lens will not be cracked or overly "milky" looking from over exposure to the sun. This lens will need to be hand polished to get the fine scratches out. Check out this video of our Gauge Tester

Four of these set at the top of the instrument cluster in the 1971-73 Cougar, evenly spaced over the four gauge pods. They are "tender" from age and heat but are intact without chips or cracks.

Reproduction printed circuit board. Fits all 1971 - 73 Mercury Cougars, XR7 (65F & 76F) and Standard (65D & 76D) models.Check out the video below on our new gauge tester: ...

Rebuilt tachometer for your 1971 - 1973 XR7 Cougar. Check out the video below on our new gauge tester: ...

Good used Grade B unit that has never had the odometer tampered with. Grade B's will have fading face paint and numbers and will need to be touched up. Check out the video below on our new gauge tester: ...

Used temperature gauge for the 72 Mercury Cougar. These gauges have been tested and will be in working condition. The 72 version has a red lens with black lettering that shows "belts" when illuminated. Ford part number D1WF-10971 Check out the video below on our new gauge tester: ...

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

This H5001 bulb is the closest Halogen Reproduction of the original FoMoCo headlight that we carry. This bulb has the number 1 at twelve o'clock (to indicate its position in the grill) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high beam is definitely going to be brighter than your original dim bulbs. Note: Other than Cougars, only 1969 Mustangs used these bulbs. Don't forget that you need to...

This H5006 bulb is the closest Halogen Reproduction of the original FoMoCo headlights that we carry. This bulb has the number 2 at twelve o'clock (to indicate its position in your grille) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high / lo beam is definitely going to be brighter than your original dim bulbs. Also note: Other than Cougars, only the 1969 Mustang used these bulbs.Don't forget...

These bulbs work with Cougar factory spec turn signal flashers, but they may not work with all aftermarket flashers, especially if they claim to 'exceed' the factory specs. Because of this, you may want to order our turn signal flasher that was specifically designed to work with the Plasma LED bulbs: Part #:12827 As seen on Gearz with Stacey David - After searching far and wide, to and fro, here and there...we finally found the best LED replacement bulb for your Cougar, Mustang...

Replacement "cool white" LED single post light bulb for 67-73 Cougar and Mustang courtesy light applications. Can also be used for trunk lights, under hood lights, under dash lights, and more. Good replacement for 97 and 631 bulb applications. Some may find Our Plasma bulbs too bright for the Opera Lights and prefer to tone it down with these. ...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Plasma LED 1157 replacement bulb in YELLOW for your parking / running lights. Much brighter than stock, more responsive, and less power draw. We won't go so far as to call these little guys AMBER, but they're definitely yellow. Good for your 67 - 73 Cougar, Mustang or anything else that takes a dual-filament 1157 bulb for marker lights or turn signals. Specs: Power: 7.5...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1076 WHITE Led Plasma back up light bulb for your 67-68 or 71-73 Cougar, Mustang or anything else you might have that takes an 1076 bulb. Please note that these bulbs are ground sensitive. Specs: Power: 7.5 Watts Brightness: 300 Lumens Total life expectancy: 30,000 hours 2" Tall (1 3/8" extends out of the socket) Comparison image - Click to view full-size: Check...

As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further. Replacement 1157 WHITE LED Plasma stop lamp / turn signal light bulb for your 67 - 73 Cougar, Mustang or anything else you might have that takes a white 1157 bulb. Please note that these bulbs are ground sensitive. Did you know that white (clear) 1157 bulbs fit a ton of other cars and trailers from the 50's clear through the 90's and beyond that used the...

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Exact reproduction with Ford logo and marking as original. Very correct reproduction right down to the Ford logo! Includes left hand and right hand lenses. Replaces Ford part number D1ZZ-15201.

Lamp housing with original glass lens, wiring pigtail, and with rubber body plug. Driver quality part. Bulbs available. We often find damaged wires with these lights left on our rear bumper cores. Guaranteed to work with no cuts or splices. Different than the 1973 version due to the bumper mounting brackets.Ford number D1WY-13550-A.

Very nice used milky white lens for all license plate lamp assemblies. No cracks or chips. Good used original OEM lens that can easily be cleaned to look as good as the Chinese reproduction.

Exact Mustang reproduction with Ford logo and marking as original. Very correct reproduction right down to the Ford logo! Replaces Ford part # D1ZZ-15201-RL. In order for you to install with the 1971-73 Cougar installed metal frames, you will need to remove the locating pin on your D1AB-15A467-B window bracket with a Dremel or similar. Original Cougar red lenses had a part number of D1WB-15A464-LH.

Exact Mustang reproduction with Ford logo and marking as original. Very correct reproduction right down to the Ford logo! Replaces Ford part # D1ZZ-15201-RRIn order for you to install with the 1971-73 Cougar installed metal frames, you will need to remove the locating pin on your D1AB-15A466-B window bracket with a Dremel or similar. Original Cougar red lenses had a part number of D1WB-15A464-RH.

Converting your headlight wiring to a modern relay type is probably one of the best 'bang for the buck' mods you can do to your classic car. A must when using modern halogen bulbs, it will also brighten your original incandescent headlights. Normally this is done by cutting the main wiring harness and splicing in a pair of relays. Most of us try to hide the relays under or behind something as well. Not only is this a time consuming task, it can be troublesome if a connection or component fails...

All new lamp housing with glass lens, bulb, wiring pigtail, and with rubber body plug. Fits all 1971-73 Mercury Cougars has extended wiring pigtail to accommodate the 1973 cars.

The Mini Relay Kit has everything you need to add relays to your headlight circuit - without cutting your wiring harness. It is equivalent to installing relays into your main harness like it was done for years, but requires no modification to the wiring harness. The differences between this kit and the full kit are redundancy and controller size. This kit has only one controller with two relays designed to handle up to a maximum of 200 combined watts and uses a wiring harness to control...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Reproduction replacement halogen bulb for your headlights. This is a clear bulb, "natural white" alternative to the "cool white" bulbs included in our halogen headlight conversion kit. 55 Watt Xenon Halogen H4/9003 bulb. Sold Individually.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

NOTE: WILL NOT FIT 69-73 COUGAR WITHOUT MODIFICATION TO THE CORE SUPPORT OR SPACING THE HEADLIGHT FORWARD APROXIMATELY 1/4" Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

This kit is what we recommend to fully convert your 1972 Cougar over to LED Plasma exterior lights.  Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time to fully illuminate and a split second can make all...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

Used passenger side (right hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Used driver side (left hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This is a "better quality" non-concours starter solenoid. It's just one step above our "generic" solenoid also listed on our site. An inexpensive replacement if you are not worried about being 100% correct. More often than not, these lower quality solenoids fail within a year or two so we always recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury...

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade A used, may have some discoloring, but not damage.Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade B, these will have some chipping or cracking present. Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Finally a fast easy way to hook up the Pertronix Ignitor©! The Ignition Power Relay installs next to the starter solenoid with a supplied self-drilling, self tapping screw. Each wire is the right length and comes with the correctly sized terminal already Installed. Simply connect two wires at the solenoid and connect the Ignitor to the red power wire. The Pertronix Ignitor© is a 12 volt device that must be powered during crank and run. Many installers mistake the coil positive for a 12 volt...

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best.Replaces Ford Part #: D1ZZ-17553 or D1ZZ-17553-A

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Used switch panel with 3 switches for all 1971-73 Mercury XR7  with convertible tops. Inspected and tested switch panel for COURTESY - MAP - TOP. All three switched prove will function and operate. Toggle tips included. Do you have extra, or non working 1971-73 XR7 convertible top switch assemblies? As long as the circuit board part of it isn't damaged we will buy them for $30. Switch assembly must be stamped D1WB-15668-AA on the reverse. *Note - Excludes Non - XR7 model...

Tested and working used 2 speed windshield wiper switch for any 1971-73 Mercury Cougar and Ford Mustang. Replaces Ford part number D1ZB-17A553.

Used seat back release relay for the 71 - 73 Cougar or Mustang. Located on the relay panel behind the glove box. Ford part number D1ZB-14C690-AA

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

This is a good used and tested power harness which goes from the circuit breaker at the starter solenoid to any of the following:1. Heated backlight (rear defroster)2. Power seat3. Seat back release4. Convertible top

Used driver side turn signal / parking lamp wiring harness with socket for the 1971 - 1973 Mercury Cougar.Ford part number D2WB-13234-AA

Used passenger side turn signal / parking lamp wiring harness with socket for the 1971 - 1973 Mercury Cougar.Ford part number D2WB-13235-AA

Used lead wire harness that runs from the white plug at the cowl to the throttle positioning sensor on the 71 - 73 Cougar or Mustang.Harness is red with yellow hash marks.