All Available Parts - 1971 Ford Mustang

Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside. 

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.

3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car. 

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Internal tail shaft assembly from a FMX transmission. We only disassemble up to what you see in the picture.  *Excludes some FMX transmissions with 351C-4v in 1970. We do not have the larger diameter version available.

Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture. 

Internal tail shaft assembly from a C4 transmission. We only disassemble up to what you see in the picture.  *Excludes later versions of C4 transmission that have thicker output shafts.

Bolt kit for installing the idler and adjusting pulley on any 1970-73 Mercury Cougar / 1970-73 Ford Mustang or 1970-73 Ford / Mercury with 302, 351W, and 351C engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 1 thick 3/8 washer.  

Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.

Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is a 8-32x1-1/2, 1/4 hex headed fine thread bolt and nut.  This is not the round headed slotted screw type that Ford also used.

Used console lid catch. Plastic piece that screws to the underside lid of your late 1970-73 Mercury Cougar or 1970-78 Ford Mustang. Yep, used on Mustang II's, too.  Ford part number D0ZZ-63060A96-B and stamped into the plastic D0ZB-63060A96-B ...

Core FMX Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 or 1971 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

Backer board for the sill plate on any 1971-73 Mercury Cougar or Ford Mustang. Also called a shield, it bridges the gap over the channel for the wiring harness. It is adjacent to the sill plate, and keeps the carpet from dropping into the exposed channel. This is a used part, and made from fiber cardboard type of material. See our reproduction item in the related items for a lower cost and made from more sturdy material. Original Ford part number D1ZZ-6513218-A. Two required per car, sold...

Backer boards (PAIR) for the sill plate on any 1971-73 Mercury Cougar or Ford Mustang. Also called a shield, it bridges the gap over the channel for the wiring harness. It is adjacent to the sill plate, and keeps the carpet from dropping into the exposed channel. This is a new part, and made from durable non paper material. See our  related items for used. Original Ford part number D1ZZ-6513218-A. Two required per car, sold as a pair.

Core FMX transmission for a 1971 Mercury Cougar or Ford Mustang. Tag number PHB-E2 or  PHB-E3. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1971 Mercury Cougar or Ford Mustang, with H code 351-2V engine. Tag number PGA-AV. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1971 Mercury Cougar or Ford Mustang, with M code 351-4V engine. Tag number PGA-AH. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with 351-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

1971 - 1973 Mercury Cougar and Ford Mustang convertible clear glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part # D1ZZ-7629710-A. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-7629711-A. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-6529710-A. *NOTE* Air conditioned cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not included. Ford part number D1ZZ-6529711-A. *NOTE* - Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

Good reproduction made in Taiwan. Much higher quality than the Chinese version of this regulator. Replaces Ford part # D1ZZ-6523206-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Fixed steering column from a 1971 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. 1971 and 1972 appear to be the same, but we will ship one from a...

D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

D0AZ-6331604-A

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

C9ZZ-2454-A

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

NOS interior driver side door handle for the 1971 Cougar or Mustang. 

Complete 22 bolt set for oil pan on the 70 - 73 Cougar or Mustang.  

Reproduction bolts and washers for the automatic transmission bell housing on any 1971 - 73 Cougar or Mustang equipped with a 351 engines and C-6 transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1971-73.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

Carter manufactured fuel pump with 4907-S, correct for 429 Cobra Jet engines.D0OZ-9350-A. Also used on Torino / Ranchero / Cyclone starting in 1970.

D1AZ-6522600-A

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

NOS new old stock intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit. *NOTE* Must be used in conjunction with an intermittent wiper controller. Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New old stock Zinc radiator cap. Motorcraft stamped, with RS 12A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9AZ-8100-A.

New old stock Chrome radiator cap. Motorcraft stamped, with RS-512A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9ZZ-8100-A.

New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description.  Ford part number 382624-S100.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Replaces Ford part #: D2WY-6543720.

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Replaces Ford part #: D1ZZ-7653986. Seven piece kit with attaching hardware.

Replaces Ford part #D1ZZ-7602626

Replaces Ford Part # : D1ZZ-7651325-A

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

NOS distributor lead wire with green boot for the coil. Direct replacement for 1968-73 Ford distributors. There were several colors of boots that go to the coil, this is a green one as shown. Ford part number C7VY-12216-A.

NOS distributor ground wire. Direct replacement for 1967-73 Ford distributors. New old stock cable for inside the distributor, non ferrous metal, brass? Ford part number D2AZ-12264-A.

New Old Stock Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on select Ford models. This is a NOS original electrical and vacuum operated switch. It has the FORD oval logo and part number D1AE-AA casting. This casting number is correct for select 1971 and 1972 Fords and Mercury. It was used on 302 351C and 351W engines. Because of the heavy demand placed on the cooling system by the factory air option this was mounted...

New old stock driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. Ford part number D1ZZ-6530147-A.

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

Remanufactured OEM Ford Boss 429 and 429 Cobra Jet manual transmission flywheel. Stamped C9AE-C. New ring gear, resurfaced clutch surface. No visible issues, no discoloration from heat. 1971 Mercury Cougar and Ford Mustang, 1970-71 Ford Torino and Mercury Cyclone and variants. 1969-70 Boss 429. Ford part number C9AE-6375-C.

D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Contains nut, lock washer, and spacer. Fits all Ford alternators.

[No Description Provided]

[No Description Provided]

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

Reproduction flexible duct end that was originally stapled to the passenger side fresh air duct, found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1ZA-18C305-AB.

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Nice lower quality ignition coil for those of you on a tighter budget. A wee bit cheaper than the other performance coils we offer like the Yellow Top Coil or the Pertronix Flamethrower series coils, but still a great buy and very reliable.   

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Stamped Steel Pointer Mounts to Timing Chain Cover. Black Zinc-Plated. Includes Mounting Screw. Correct for 289, 302 and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and used harmonic balancers with 4...

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Contains nut and washer. Fits all Ford alternators. AMK F-644.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

Wiring harness segment to the convertible power top pump on any 1971-73 Mercury Cougar or Ford Mustang. Part number D1ZB-15A668-AB.

Wiring harness segment from firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang.  Part number D1WB-15A690-AA.

Wiring harness under hood segment from circuit breaker through the firewall to the convertible power top switch on any 1971-73 Mercury Cougar or Ford Mustang.  Part number D1ZB-15A669-A.

Reproduction Hurst shift lever for all 1970 and 1971 Mercury Cougar or Ford Mustang with factory installed Hurst shifters. Excellent reproduction in every way.Link to the expert on Ford shifter linkages.Click on images to enlarge. ...