All Available Parts - 1970 Mercury Cougar

8-32 screw for attaching the window regulator drive arm slide, to the rear channel bracket on 1969-70 Mercury Cougar and Ford Mustang with glue in glass. 8-32 Phillips oval head machine screw.

Used bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually.

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do...

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. OK reproduction, but the...

Complete reproduction passenger side bolt in door glass mounting kit for the 1970 Cougar or Mustang. This kit includes both front and rear brackets w/ rubber backing, 2 door run guides w/ inserts, both window stops and all related hardware needed to complete installation. If you want to upgrade your door glass runs to the new reproductions, you can find them here. Door glass not included. ...

Complete driver reproduction bolt in door glass mounting kit for the 1970 Cougar or Mustang. This kit includes both front and rear brackets w/ rubber backing, 2 door run guides w/ inserts, both window stops and all related hardware needed to complete installation. If you want to upgrade your door glass runs to the new reproductions, you can find them here. Door glass not included. ...

Locking nut for attaching the door window regulator to the window channel bracket on any 1969-70 Mercury Cougar or Ford Mustang. While we do not sell the T-bolts for attaching to the regulator, we do have a retainer to keep it in the front channel bracket. Find it here.

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. Often the originals are worn down from lack of lubrication which will cause your door glass to rattle. The originals were more of a clear plastic, these are white in color. These do not fit quite as well as the originals, but work as long as you are OK with the slight play.  For a tighter fit, we recommend that you see the customer reviews of this product for suggestions that...

New bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually. Black silicone is a good substitute for the seal.

383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

3M brand two part channel bonding adhesive for gluing in the Mercury Cougar or Ford Mustang door side glass and rear quarter glass. This is the best product on the market for re-gluing those troublesome 1969 side windows. We use this product for our own cars here at WCCC and have found an applicator that works great. If you just need an applicator to do just your car, we have a 60 day loaner you can use right here. However, if you are doing multiple cars or other parts, you may want to...

Grade B used. Rear door window stop bracket. Stops the window in the up position. Application driver side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Plan on replacing the felt, the rubber dipped section will also probably be cracked. One per door. Plate and bolts not included. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Window guide or 'elevator'. 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually. Ford master part number D0ZZ-65222A56-A. *Note will not have original plastic bushing inserts installed. Consider reproduction inserts, or plan on re-using your originals. 4 total inserts needed per window guide. Ford part # D0ZB-65223A00-A. *NOTE* This can also be used in conjunction with 69-70 (early) glue in glass. The 69 version is identical except for that 69 was...

Rear bracket for mounting in the 1970 door glass on the passenger side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Ford part # D0ZZ-6521430-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Rear bracket for mounting in the 1970 door glass on the driver side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Ford part # D0ZZ-6521431-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Bolt in door glass bushing for most 1970 Ford cars with bolted in door windows. This is the white plastic version. Starting in mid-1970 this bushing was made out of black plastic. Except for color they are interchangeable. Ford part # D0ZZ-6523258-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Front bracket for mounting in the 1970 door glass on the passenger side (right hand) door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part # D0ZZ-6523288-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly...

Front bracket for mounting in the 1970 door glass on the driver side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price. We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part # D0ZZ-6523288-B. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

Plastic covers for the seat belt shoulder straps on the 1970 Mercury Cougar and Ford Mustang. Sold as a Pair. Replaces Ford Part #: D0ZB-6560234, D0ZB-6560235.

These are great for your back seat belts or convertibles that did not use retractors in the front. They are an exact copy of the originals that were available as a dealer option from 1964 and up. Sold Individually. Made in U.S.A. Replaces Ford Part #: C4AZ-65611A06. Customer feedback: I just wanted to tell that your delivery has arrived today. Thanks a lot! Never ever ordered something (not even here in Germany) and got it that fast. Awesome! My next orders will go to your place and I will...

Includes one lap belt, the mounting bolts and washers.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually

Great looking replacement style seat belt. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. These are great lap belts for convertible cars that don't use retractors. We suggest using seat belt anchor bolts for an easy installation of these aftermarket lap seat belts. This kit does come with installation hardware, but the threads on the bolt are coarse, and will not bolt into your original threaded anchor points. sold individually ...

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

These are era-correct looking seat belts at an affordable price.  These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! sold individually

This is an original looking seat belt at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! SOLD INDIVIDUALLY

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Used bolts, and usually new washers. Coupe kit comes with 4 - "A" bolts, 4 "B" bolts, and 2 "D" bolts, 12 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang coupes. Coupes or hard tops will have shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded.  There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original starburst decal, which will be faded and need replacing. Find the replacement decals here. Spring is included.

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...

This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...

Used seat belt buckle bezel for the Mercury Cougar, Ford Mustang, or Ford Torino. This is the outer portion of the two piece seat belt buckle cover. This is a good replacement part if you want to keep your car original. These bezels will be free of cracks and breaks. Please specify which color you're looking for when ordering. Keep in mind that there are only a handful of colored buckles available, so we'll do our best to get you the color you need. Check out our video "All about seat belts"...

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. This is a used part, and they will typically have a very small depression from wear. They can be installed 180° and be good again. Replaces Ford part # C9ZZ-6521496. Reproduction inserts are available. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

This is a metal "C" channel that glues to the bottom center of the glued-in door glass on 1969 and early 1970 Mercury Cougar and Ford Mustangs. This channel, helps protect the glass when lowered to the rubber stop at the bottom of the door. Ford part # C9ZZ-214A16-A. *HINT* Use the same professional grade of glass adhesive that you use for bonding the door glass to the two glass mounting brackets. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

Bracket or flat piece of channel for the sliding part of the window regulator Right and left interchange. One per door, screws are included. 1970 Mercury Cougar and Ford Mustang bolt in door glass. Attaches to the 1970 rear window bracket with nuts. Ford part # D0ZZ-6521504-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.

When placing your order, be sure to leave a note as to which color you're looking for and we'll do our best to find them for you. Limited quantities available. This colored face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are...

Reproduction set of front seat belt bolts for your 69 - 70 Cougar or Mustang. Included are the 4 bolts, 4 large washers and 4 anti rattle gaskets.

Used black set of grade A seat belts for the standard model 1970 Cougar. If you would like to save a bit of money, we can put together a set of grade B belts, which would have a small amount of rusting on the chrome areas, a bit of fraying on the belts and a small crack on the retractor sleeve. Give us a call to inquire.Does not include hardware.

These reproduction face plates fit inside the buckle bezel on the two piece type seat belt buckle cover. Sold as a pair. You can use your existing spacer, or if you're missing one, you can find it here. Check out our video "All about seat belts" below. ...

Now you can restore your 1968-72 Cougar or Mustang’s deluxe seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair...

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged.  Check out our video "All about seat belts" below. ...

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

These are Concours quality with correct bevel and markings.. Sold as a pair.

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

DROP SHIP ETA - 4 WEEKSUnbelievable, truly authentic concours restoration quality reproduction spoiler kit includes the wing blade constructed of an ABS based thermoplastic and is molded in gray (as original). It's not fiberglass. This two-piece wing (as original) derives its rigid stability from the material itself (as original) instead of some secondary internal support such as a metal rod or foam. And it's not light weight, it's the right weight... at over 8 lbs.! All dimensions are...

Reproduction original style chin spoiler. Nice quality, fit and finish. Made from thin plastic just like the originals. Comes as bare black plastic, so we suggest coating with your favorite semi-gloss black paint for a more finished look. Take a look at the 1:33:00 mark in the video below to see how we compare the reproduction to the original: ...

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent. 

Reproduction 15 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction 2 piece spinner assembly for the new HB45 Legendary Series aluminum wheel. The aluminum die cast threaded stem mounts from the back side of the wheel and the chrome spinner truly spins on from the front. Set screw is included to prevent loss. NOTE: Will only fit the HB45 Legendary WheelCheck out our video on Legendary Wheels below: ...

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Used and tested original sequential unit for the 1969 - EARLY 1970 Mercury Cougar. This unit will come with a 90 day warranty. Keep in mind that if you want to use the brighter LED's on your car, this original sequential system will not work. If you want to change over to LED, you will need the updated sequential unit which you can find here. If you need the sequential enclosure box, you find our used boxes here. ...

Used and tested sequential unit for the taillights of the late 70 - 73 Mercury Cougar. This unit will come with a 90 day warranty. Keep in mind that if you want to use the brighter LED's on your car, this original sequential system will not work. If you want to change over to LED, you will need the updated sequential unit which you can find here. If you need the sequential enclosure box, you find our used boxes here. Ford part # D1WY-13A366-A. *NOTE* Need help diagnosing a...

Used turn signal flasher for the 1970 Mercury Cougar Ford Part number DVB-13350-A

Used emergency flasher for the 1970 Mercury Cougar Ford Part number D0WB-13350-B

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...

Reproduction castle nut for multiple applications, including the power steering control valve, strut rods, ram cylinder and ball joints on the 1967 - 1973 Cougar or Mustang.  Dimensions: 9/16" - 18.

Reproduction pair of A/C vent registers for your 69 - 70 Cougar or Mustang. Sold as a pair. Replaces Ford part numbers: C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side.

Reproduction OE spec reproduction of the three spoke woodgrain deluxe rimblow steering wheel. This is the exact size and feel as the original, and has the correct factory detail on the spokes and center hub. Included are the wheel, gap cover and installed rimblow switch. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Used convertible top flapper stopper. Technically called a "lasting", this is the thin strip of 1/16" thick metal that slides inside the sleeve of your convertible top to keep it from flapping. We will rarely have these on hand, so we've included the dimensions so that you can fabricate your own if needed. 2 required per vehicle.

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

Used pair of 31 spline axles for the 68 - 70 Cougar or Mustang, equipped with the Boss 302, 427 and 428 CJ engines all with 9 inch rear axles. Most all other vehicles used 28 spline axles. Short axle 27-1/16" inches long and long axle 31-1/8" inches long. Ford part numbers C9OZ-4234-C and C9OZ-4234-D. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. ...

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

Used passenger side seat back release catch for the 68 - 70 Cougar or Mustang.

Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California.  Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Inglewood, California.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Pair of reproduction license plate frames bearing the name of the original Lincoln / Mercury dealer lot in Portland / Beaverton, Oregon.  Chrome frames with the city and dealer name written in/on reflective material. Sold only as a pair.

Reproduction deck lid for the 69-70 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

Designed by an engineer and original owner of a 1970 Cougar convertible, this brace is ideal for those wanting to brace their car prior to removing key structural parts. It was designed for a 69-70 Cougar Convertible but will work well on any 67-73. We Strongly suggest that once you are done with this item you return it for a 80% refund as this is our only unit at present and we want as many folks as possible to benefit! Thank you Dan Pobloskie in North Prairie, Wisconsin for sharing your...

Reproduction coil spring seat pad for the 67 - 73 Cougar or Mustang.  Sold individually, 4 needed per car.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a big block engine. This item requires a $30 core charge.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.

Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock

Used pair of red diffusers for the temperature or fuel gauge on the 69 - 70 Mercury Cougar. The wording (alternator, park, brake, oil etc.) is on the actual lens and not the diffuser, so these can be used on either gauge.Sold as a pair.

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.