All Available Parts - 1970 Mercury Cougar

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Used coil mounting bracket. This version of the bracket is probably the most common. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. This version has the notch as shown. We know that this version was used on...

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

Key stock for 1967-73 Ford V-8 engines 3/16" square straight keys. Ships in 4 inch lengths, cut to fit the different applications. Common sizes 289/302 1-13/32", 351 1-3/4", etc.

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines for 1968-70 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, 1-1/16 inches thick and has the timing marks on rim. Refundable $50.00 core charge when a rebuildable C8AE-6316-A harmonic balancer is received by WCCC. Ford part # C8AZ-6316-B, Ford casting # C8AE-6316-A.*NOTE* Excludes 1967 S code 390-4V...

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number D0AE-A casting.This casting number is correct for all 1970 1971 1972 and 1973 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy...

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable C8AE-6316-C core at WCCC. *Note - Excludes 1969 - 1970 428 non dragpack Cobra Jet engines.Click on images...

ETA FOR THIS ITEM IS 8/23/2023Decent off shore part. Since good used cores are very expensive and almost impossible to find this is often the only choice.

D0AE-6316-A All 1970-73 351C-2V and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. There is a $50 core charge for this part.*Note - Excludes 1971 and later 351-4V engines. **Note - When ordering double check that you have a 351 Cleveland engine. It is not...

D0AE-6316-A All 1970-73 Mercury Cougar 351C-2V engines, and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. We save the very best used harmonic balancers, those that do not actually need rebuilding. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. Price includes $55 core charge. Refundable $50.00 core...

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines 1968 - 1970 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, and 1-1/16 inches thick. Has the timing marks on rim.  The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. Refundable $50.00 core charge when rebuildable D0OE-6316-C harmonic...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be...

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable D0ZE-6316-A core at WCCC. *Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.Click on images to enlarge. This is a picture of a 40 year old piece of rubber removed from a harmonic...

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/29/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 12/5/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/67

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/25/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 8/26/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/28/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 1/26/70

Reproduction 14" length economy breather cap hose for the 68 - 70 Cougar or Mustang.

C9OE-9425-A or -F Cast iron intake manifold used on all 1969-70 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-A or -F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-A. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D0AE-9425-M Cast iron intake manifold used on all 1970 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-M. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.

Used C8OE-9425-C Cast iron intake manifold used on all 1969 - 1970 Q and 1968 - 1970 R code 428CJ and 428SCJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8OE-9425-C . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford part number C8OZ-9424-B.  Current date code is 9C25 or March 25, 1969 and 0A19 or January 19, 1970. *Trivia - One of the heaviest...

Reproduction intake manifold bolts for the Mercury Cougar Eliminator or the Ford BOSS Mustang equipped with the 302 BOSS engine. These units are sold individually.Replaces Ford part # 56146-S.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...

This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. 

This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.

Replacement steel tube for all FE intake manifolds. Tube connects to water pump via a rubber hose. Fits all FE - 352, 390, 410, 427, 428 engines. Best to replace when intake manifold is removed to drive out the old rotted steel tube. We use a little silicone on the smooth surface prior to installation. The connecting hose (and clamps) to water pump normally got painted Ford engine blue from the factory.

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

Used cast iron choke stove from any 1970 351C-4V Ford engine. This is held on with 2 bolts. Casting number on the iron plate is D0AE-9A705-C, which is only for the plate. The plate and tube assembly has a Ford part number of D0AZ-9C869-A. No hardware included. Limited to stock on hand.* Note - for those who do not need the choke stove, a cast aluminum block off plate can be purchased through Summit.

Set of bolts and studs for the intake manifold on any 1970 Ford 428 Cobra Jet engine. The 1970 set includes a second double ended stud, while the 1969 set only includes 1 double stud. 1970 R and Q code Mustang and Cougar.Trivia - 1970 Mercury Cougars only have a Q as the 5th digit in the VIN code. Yes, All 1970 428 cobra jet Cougars are designated as Q codes. Ram air was optional and will show on the window sticker or Marti Report.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-4V engine. AMK F-1321.*Note - Excludes 351C-2V and 351W engines.

Set of 16 bolts for the intake manifold on any factory 1969-70 Ford 351W-2V and 351W-4V engine. AMK F-1131.*Note - Excludes all 351 Cleveland engines.

Set of 12 bolts / spacers / stud for the intake manifold on any factory 1969-70 Ford S code 390-4V or 428 Cobra Jet or 428SCJ engine. AMK F-475.*Note - Excludes 1967-68 390 engines.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-2V engine. AMK F-1313.*Note - Excludes 351C-4V and 351W engines.

5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786

Over 100 total vacuum caps in 6 different sizes.

Just about the only possible reason to put this poor quality reproduction on your Cougar is that it is a good tool to put out engine fires. No Joke! If you happen to have an engine fire you can carefully open your hood, yank the blanket downward and smother the fire by pushing the blanket tight around the area that is burning. This can at least buy you time until a fire extinguisher is located. How do I know? I saved a very pristine 1974 XR7 a few years ago this way! This inexpensive product...

These original hood blanket clips grip much better than the reproductions. Usually there were 10-11 of these clips used but it can vary from car to car as they tended to be inconsistent at the factory on how many of the available holes they actually stuck a clip into. Sold Individually.

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet.  Replaces Ford part # C9AZ-2167-B.

Concourse Correct Brass Vacuum Hose Tie, used to dress up the distributor vacuum hose. Replaces Ford Part # 383313-SB

Concourse Correct Vacuum Hose Aluminum Tie, used to dress up the distributor vacuum hose. Replaces Part # 383313-SA

Used vacuum tree for any 1970 Mercury Cougar, Ford Mustang, or 1970-71 Ford Torino. This manifold assembly mounts to the firewall in the engine compartment, and is unique to the above applications, as it has 6 different vacuum outlets or sources. These connect to the brake booster, heater / air conditioning vacuum parts, and other accessory items that use vacuum. Replaces Ford part number D0OZ-9C490-A or D0OA-9C490-A.

Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.

Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Reproduction Concours Correct muffler hangers for your 1968 - 1970 Mercury Cougar.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Inside diamenter = 1"

Used plastic clip for the Mercury Cougar or Ford Mustang

Six required per car.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used Trunk Light Wire Plastic Clip for the 1967 - 1973 Mercury Cougar

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part # 383104-S.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible.

Used plastic clip for the Mercury Cougar or Ford Mustang.

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

New reproduction wire loom clip for the lower radiator core support.

Used black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Found on the lower radiator core support.  4 clips needed to attach the wiring harness and the vacuum hoses for the headlight system. Sold Individually. Replaces Ford part # 383104-S.

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.

New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970. Replaces Ford part # C9AZ-9H576-A.