All Available Parts - 1969 Ford Mustang

NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

New Old Stock NOS passenger side front turn signal bezel. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13210-A, casting number C9WB-132_7

New Old Stock driver side front turn signal lens for 1969 Mercury Cougar and 1969 Ford Mustang with sport lamps.Ford part # C9WY-13209-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

New Old Stock NOS driver side front turn signal bezel. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13212-A, casting number C9WB-13237-A

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

Reproduction washer for the interlock on all top loader 4 speed transmissions as found on 1967-69 Mercury Cougar and Ford Mustangs.Ford part number C5ZZ-7C318-A.

Contains nut and washer. Fits all Ford alternators. AMK F-644.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

This manual shows exploded diagrams and part numbers of all the motors Ford used in 1969, not just the Cougar. I use this manual almost daily for identifying air conditioning brackets and various pulleys.

Reproduction 4 Speed shifter lever for any 1969 Mercury Cougar and Ford Mustang with V-8 engines. Original Ford part number C9ZZ-7210-B. Excellent reproduction. Link to the expert on Ford shifter linkages.  *Note - Must be used with Trunion C9AZ-7210-J, sold separately. Check out our video on rebuilding your shifter below: ...

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Contains nut, lock washer, and spacer. Fits all Ford alternators.

[No Description Provided]

[No Description Provided]

Nice quality hardware for attaching the shift rods to the bottom of the shifter mechanism. Won't work with the 1970-73 Hurst shifters, but does work with all of the others. Including 3 speeds, sorry, sold in packages of 3 though. Check out our video on rebuilding your shifter below: ...

Designed as a direct-fit OE-style replacement, this modulator valve will fit directly into the factory location of your current Cougar or Mustang valve. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs.

This cup holder fits snug into the seat belt receptacles in your 69 Mustang or Cougar center console. Very useful cup holder that does not require modification to take in and out.

Give your Cougar or Mustang that cool, classic look by adding these replica California black and gold license plates. These plates are favored by classic car owners everywhere, because they signify a rust free, restored classic car. These plates are real stamped aluminum with raised numbers and letters. Sold Individually.

Special clip for attaching the pull cable to the right or left fresh air vent on any 1969-70 Mercury Cougar or Ford Mustang.

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

This is the driver side trim / moulding that mounts to the door window and creates the seal between the door glass and the quarter window on 69 Cougars and Mustangs. Get the seal you need for this moulding here.

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...

Nice lower quality ignition coil for those of you on a tighter budget. A wee bit cheaper than the other performance coils we offer like the Yellow Top Coil or the Pertronix Flamethrower series coils, but still a great buy and very reliable.   

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Stamped Steel Pointer Mounts to Timing Chain Cover. Black Zinc-Plated. Includes Mounting Screw. Correct for 289, 302 and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and used harmonic balancers with 4...

Concourse Correct Timing Pointer for the 1968 - 1970 390, 390GT or 428CJ. Technically, by design, this is a copy of a 1969-70 390/428CJ timing pointer. It will also work for 1968, since the harmonic balancers and timing covers are the same.Replaces Part # C9AZ-6023-A.* Note - not correct for 428 Super Cobra Jet, see related item.

Concourse Correct Timing Pointer for any 428 Super Cobra Jet Replaces Part Number C9OZ-6023-A.

3/8-16 X 7/8 9/16 AF .75 OD Sold individually. Fits all 390 & 428. Replaces Ford Part #: 374409-S.

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Original used 390 or 428 Cobra Jet piston connecting rod. These are marked C7AE-B. Rods and caps only. We strongly suggest using ARP aftermarket rod bolts. Limited quantity available, call to inquire. Replaces Ford part number C7AE-B and C6AZ-6200-C. *Note - Excludes 428 Super Cobra Jet engines.

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

White reproduction fan for the Thermactor Smog Pump.

Bolt kit for installing the idler and adjusting pulley on any 1968-69 Mercury Cougar / 1968-69 Ford Mustang or 1968-69 Ford / Mercury with small block 289 / 302 / 351W engines. 4 bolts 3/8-16x7/8 inch washer head bolts.  

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Fuel pump drive eccentric for most big block Ford engines 1963-70. Including 352, 360, 390, 410, 427, and 428. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 3-3/8 inches in diameter. Ford part number C3AZ-6287-A.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Concours correct engine pipe donut, metal, factory original dual sized design to properly seal H-pipe to Exhaust manifolds MCA approved, sold individually.Replaces Ford Part # C8LV-9450-AFits between exhaust manifold and header pipe (H or Y pipe) 2 1/16 id 3 5/8 od cast iron, tapered top and bottom, smooth inside.Note! These are very difficult to seat compared to the pliable ones we sell. If you do decide to use the steel version it is recommended you apply a liberal coating of Permatex High...

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust manifold flange rings or 'doughnuts' for stock cast iron 428CJ exhaust manifolds. These are the malleable type that conform and slightly crush. Inside diameter just over 2-1/8 inches. Sold individually, two needed per car.

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Reproduction bolts and washers for the manual transmission bell housing on mid , like Feb 1968 - 1970 Cougar or Mustang or other Ford car equipped with a 390 / 428 engines. Bell housing to engine block bolts.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Phillips flat head machine screw for attaching bucket seat, seat back release catch on any 1968-70 Mercury Cougar or Ford Mustang including bench seat cars. Original screws are trilobed, meaning that they have triangle shaped threads instead of perfectly round. Helps with locking. We recommend using locktite or some other thread sealer when installing. Or at least check the torque after several weeks of use. 5/16-18 flat head machine screw, zinc plated.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.

Reproduction Clutch Pedal Rod To Firewall Seal. Replaces Ford Part #: C6OZ-7533.*NOTE* From personal experience we have found these do not stay attached to the firewall as well as the originals. An adhesive will remedy this problem.

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.

This Steering Box Cover Gasket Reproduction fits the 67, 68, 69, and 70. Replaces Ford part #: C3DZ-3581. If your original steering box is one of the few that is still tight then you will want to open it up, clean out all the decades old solidified grease and put new grease in.

Sold as a pair, correct for coupe or convertible. Will fit the 70 coupe or convertible as well, but correct for the 1969. Replaces Ford part # C9ZZ-6528182 & 3B. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Seals the lenses to the light body mounted in the front valance. Replaces Ford part # C9WY-13211. Sold as a pair. Also used on 1970 Mach I and 1969 - 1970 Shelby.

Replaces C9AZ-15447. Sold as a set of four.

Replaces Ford part #C7AZ-13568

Fits along the lip of the cowl cover and seals to the underside of the hood. Replaces Ford Part #C9ZZ-16740. 

44 Piece kit that includes quarter panel drain plugs.

This kit is designed for the 1969-1970 heater A/C box. Replaces Ford Part #: C9ZZ-18500-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Correct heater box seal kit for 1969 and 1970 Cougars and Mustangs. Replaces Ford part #: C9ZZ-18500-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.

These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.

This reproduction is made from the original Ford tooling and is new to the market. Well worth the few extra dollars over the previous ones offered. Replaces Ford Part #: C6OZ-7513-A.

Used to seal the Aluminum shifter housing to the transmission tunnel. Replaces Ford part #: C9ZZ-7370. Check out our video on rebuilding your shifter below: ...

We suggest using white lithium grease or petroleum jelly to ensure the seal will not stick to the shift lever. Fits 1969-73 Mercury Cougar and Ford Mustang, additionally it also fits 1971+ Maverick and Comet with floor shift automatic only.  If you have any side-to-side play in the shifter, this seal will not last. We do have the shifter bushings available. Replaces Ford part  numbers C9ZZ-7D351-A & D1ZZ-7D351-A. Get the matching mounting clips here. Check...

Reproduction cowl cover to hood rubber bumpers for the Mercury Cougar or Ford Mustang. These little units attach to the front of the cowl cover for the back corners of the hood to sit on. These will also work for the 1967-68 Mercury Cougar or Ford Mustang fuel filler door bumpers if you are missing them. Sold as a pair and comes with the attaching screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate...

Perfect fit. Replaces Ford part #: C9ZZ-3513.

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out our video on rebuilding your shifter below: ...