All Available Parts - 1969 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 601-700 of 3572
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 13742 -
Bushing that goes to the inside of the brake booster pushrod. This is the early version of this part that is made of plastic, a later version was introduced in 1969 which was made of nylon and is/was more durable.
Availability: Out of Stock
Item #: 24833 -
For use with a clutch pedal. Longer arm than drum brake pedals. Keep in mind you can trim an automatic brake pedal to work on a manual transmission application. Pedal shipped bare, picture may show hardware and pedal pad with trim. 1969 and 1970 disc brake pedals can't be interchanged without changing the brake booster push rod.
Availability: Used / Wrecking Yard Item
Item #: 24849 -
C9ZZ-6501508-B This is the correct hanger for a 1969 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number C9ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...
Availability: In-Stock Item
Item #: 13717 -
Replaces Ford part # C9ZZ-2455-A. Features a longer arm than manual drum brake pedals as it mounts in a different place on the pedal hanger than a manual pedal. Works only with 1969 Bendix booster teardrop shaped power brake booster rod. The pictures below show a correct 1969 only pedal mounted to a 1969 Bendix booster and 1969 only hanger. Look at the pictures closely, many customers have found that their problems are a result of previous owners installing parts from other years. This pedal...
Availability: Used / Wrecking Yard Item
Item #: 24830 -
Longer arm than drum brake pedals. Works only with 1969 power brake booster rod. The pictures below show a correct 1969 only pedal mounted to a 1969 only booster and 1969 only hanger. Look at the pictures closely, many customers have found that their problems are a result of previous owners installing parts from other years. Pedal shipped bare, picture may show hardware and pedal pad with trim. Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 11-0417 -
Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.
Availability: In-Stock Item
Item #: 14-0014 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...
Availability: In-Stock Item
Item #: 14-0015 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...
Availability: In-Stock Item
Item #: 14-0033 -
New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...
Availability: In-Stock Item
Item #: 14-0085 -
This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...
Availability: In-Stock Item
Item #: 14-0075 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.
Availability: Out of Stock, On Order
Item #: 14-0077 -
VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.
Availability: In-Stock Item
Item #: 14-0090 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...
Availability: In-Stock Item
Item #: 14-0092 -
WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.
Availability: Used / Wrecking Yard Item
Item #: 16174 -
Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...
Availability: Out of Stock
Item #: 33144 -
New Old Stock 'DEFOG' knob. Attaches to hand down defog switch on 1969-70 Mercury Cougar and Ford Mustang with rear defogger option. *Note - Excludes 1970 Mercury Cougar XR7. Those cars had the defog switch in the courtesy light panel. Replaces Ford part number C9WY-18519-A.
Availability: Used / Wrecking Yard Item
Item #: 12998 -
Used timing chain cover from a 351W or Windsor engine from 1969-70 Mercury Cougar and Ford Mustang or most any 1969-70 Ford with 351W. Honestly, we have found that most of the 1969 production year came with the C8AE-6059-A timing cover. Cast aluminum construction without excessive damage. Installation bolt kits also available. The C8AE-6059-A timing cover can be used on 1970 302 and 351W engines, as long as you use the 1970 timing pointer. The 1970 timing pointers use alternate...
Availability: Used / Wrecking Yard Item
Item #: 12969 -
Used timing chain cover for any 390 or 428CJ engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968-70 Ford with 390 or 428 cubic inch engines. Cast aluminum construction without excessive damage. Installation bolt kits also avialable. Ford casting number C8AE-6059-B. *Note - Is not technically compatible with 1967 or earlier 390 engines.
Availability: In-Stock Item
Item #: 25984 -
Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...
Availability: In-Stock Item
Item #: 26094 -
This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...
Availability: In-Stock Item
Item #: 41791 -
This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.
Availability: In-Stock Item
Item #: 14037 -
This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength. Replaces Ford part # C8ZZ-19A566.
Availability: Used / Wrecking Yard Item
Item #: 11-0019 -
Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...
Availability: Used / Wrecking Yard Item
Item #: 11-0319 -
Original two piece assembly that bolts to the passenger side of your firewall on AC equipped Cougar's. Comes as taken from parts car. If you own a 1969 Cougar you will need to look at the configuration of the evaporator lines. During the 1969 model year this grommet bracket changed to reflect the running year change. Ford part # C9ZA-19B588-C.
Availability: Used / Wrecking Yard Item
Item #: 11-0056 -
Used OEM Ford heater blower motor resistor for cars with factory installed air conditioning, it attaches to the A/C blower fiberglass housing. Fits all 1969-73 Mercury Cougar and Ford Mustang with integral or factory air conditioning. The reproduction resistor that fits the 1967 - 1968 Cougar and 1965-1968 Mustang has a different hole pattern. According to manufacturer information (INDAK), the OHM output for this switch makes it incompatible with the earlier reproduction resistor. We inspect...
Availability: In-Stock Item
Item #: 10524 -
New heater blower motor resistor that attaches to the heater blower fiberglass housing. Ford part # C8OZ-18591-A.1970 and Later Maverick and Comet1971 and Later Lincoln
Availability: Used / Wrecking Yard Item
Item #: 11-0058 -
For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Ford part # C9ZZ-19858-C.
Availability: Used / Wrecking Yard Item
Item #: 11-0062 -
Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1969-70 variety, which have specific colored wires and leads....
Availability: Used / Wrecking Yard Item
Item #: 11-0066 -
Used air conditioning evaporator core, for most of the 1969 model year. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a...
Availability: Used / Wrecking Yard Item
Item #: 11-0064 -
Used air conditioning evaporator core, for most of the 1969 model year and all of 1970. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have...
Availability: Used / Wrecking Yard Item
Item #: 11-0104 -
This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.
Availability: In-Stock Item
Item #: 12328 -
This plastic A/C linkage arm for any 1969-70 Mercury Cougars and Ford Mustang. Over time they become very brittle and since the little vacuum actuator that they are connected to is so strong, they often break if any obstruction is encountered within the rectangular duct or around the linkage.You can find the retainer clips here, 2 required.Find the washer here, 1 required. ...
Availability: Used / Wrecking Yard Item
Item #: 11-0116 -
Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.
Availability: In-Stock Item
Item #: 11998 -
Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.
Availability: In-Stock Item
Item #: 12333 -
Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.
Availability: Used / Wrecking Yard Item
Item #: 11-0325 -
Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...
Availability: Used / Wrecking Yard Item
Item #: 11-0329 -
Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 22665 -
Rear defog conversion kit for most 1969-70 Mercury Cougar and all 1969-70 Ford Mustang Coupes. Includes hang down switch with wiring, long harness to blower motor, and blower motor and grille cover which installs in the rear package tray. Please see your electrical schematic for connection details. Excludes 1970 XR7 models, those cars had the defog switch integrated into the XR7 switch panel. This set up can easily be installed into a 1969 XR7 as well. You may need to purchase an accessory...
Availability: Used / Wrecking Yard Item
Item #: 11-0328 -
Shaft or rod for air inlet damper door for any 1969-70 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0334 -
Shaft or rod for the evaporator damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...
Availability: Used / Wrecking Yard Item
Item #: 11-0342 -
Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0338 -
Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0339 -
Shaft or rod for the A/C damper blower door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1969-73 shaft is clocked differently than the 1967-68 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...
Availability: In-Stock Item
Item #: 12280 -
Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.
Availability: In-Stock Item
Item #: 30102 -
Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.
Availability: Used / Wrecking Yard Item
Item #: 11-0372 -
Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...
Availability: Ships Direct from Supplier (Except International)
Item #: 30205 -
Usually ships in 3-5 business days. Reproduction heater box with A/C for 69 - 70 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). This assembly comes with two heater core gaskets, one for early 69 and one for late 69 - 70. NOTE: We've received some helpful...
Availability: In-Stock Item
Item #: 11-0386 -
Air conditioning fan blower assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.
Availability: In-Stock Item
Item #: 30825 -
For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine from 1969-73. Original condensation drain hose from the A/C case, through the floor board, to the ground. Replaces Ford part # C9ZZ-19858-C.
Availability: In-Stock Item
Item #: 26197 -
Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.
Availability: Used / Wrecking Yard Item
Item #: 11-0447 -
Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...
Availability: In-Stock Item
Item #: 32255 -
Premium reproduction rubber grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Molded rubber exactly like the original! Other reproductions on the market are die cut from sponge rubber sheets and nothing like the original. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years. ...
Availability: In-Stock Item
Item #: 11-0470 -
Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version.
Availability: In-Stock Item
Item #: 11-0473 -
Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.
Availability: Used / Wrecking Yard Item
Item #: 11-0475 -
Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...
Availability: Used / Wrecking Yard Item
Item #: 11-0511 -
Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...
Availability: Used / Wrecking Yard Item
Item #: 11-0512 -
Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...
Availability: In-Stock Item
Item #: 41704 -
Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.
Availability: In-Stock Item
Item #: 25992 -
Our heater cores are the finest available anywhere for any price and they are constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part. Replaces Ford Part #: C9ZZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...
Availability: In-Stock Item
Item #: 41348 -
Reproduction heater duct nylon rivet #375064-S is sold individually.
Availability: In-Stock Item
Item #: 19955 -
Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....
Availability: Ships Direct from Supplier (Except International)
Item #: 19897 -
Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...
Availability: In-Stock Item
Item #: 41405 -
Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...
Availability: In-Stock Item
Item #: 10479 -
Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.
Availability: Used / Wrecking Yard Item
Item #: 11-0291 -
Metal fan wheel or squirrel cage for any 1969-70 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-3/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Availability: Used / Wrecking Yard Item
Item #: 11-0289 -
Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Availability: Used / Wrecking Yard Item
Item #: 11-0383 -
Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1969-73 Cougars and Mustangs, but also on 1968 and newer Fairlanes, Torinos, Rancheros, Cyclones, and Montegos. Also installed on 1970 and newer Mavericks / Comets, plus 1971 and newer Lincolns.Ford part # C8OZ-18591-A.*Note - Excludes Heater with...
Availability: In-Stock Item
Item #: 11-4003 -
Used mounting plate for the heater blower motor on the 69 - 70 Cougar or Mustang without A/C.Keep in mind that this same plate can be used on a 67 - 68 Cougar and Mustang heater blower motor with A/C.
Availability: Out of Stock
Item #: 11-0030 -
Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A
Availability: Used / Wrecking Yard Item
Item #: 11-0031 -
C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...
Availability: Used / Wrecking Yard Item
Item #: 11-0032 -
C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...
Availability: In-Stock Item
Item #: 26157 -
Concours correct red striped heater hose for all 1969 Mercury Cougars and Ford Mustangs WITHOUT air conditioning. Correct for use with all V-8 engines. Durable red striping with "Autolite" spelled out and dated H8H02A. Some length trimming may be required for a tight looking fit.
Availability: In-Stock Item
Item #: 26159 -
Concours correct red striped heater hose for 1969 Mercury Cougars and Ford Mustangs with factory or integral air conditioning. Durable red striping with "Autolite" spelled out and dated H8H02A. These hoses have a correctly molded 90 degree elbow on one end that fits on the water valve side. Some length trimming may be required for a tight looking fit.
Availability: Used / Wrecking Yard Item
Item #: 11-0051 -
C9ZA-18C433-C lower heater duct to floor outlet for Cougars and Mustangs without air conditioning. Used grade "A" part and may have one very minor defect. This part might have a small crack, but it will not have any broken or missing tabs. It's good, it's cheapish, you want it.
Availability: Out of Stock
Item #: 12335 -
New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!
Availability: In-Stock Item
Item #: 13682 -
New clear plastic lens or face plate for the ultra rare Power Ventilation option, heater control with power vent on all 1969 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. The Power Ventilation option added a center vent to the dash as was found on factory air conditioning cars. Just more outside air circulation.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff...
Availability: Used / Wrecking Yard Item
Item #: 11-0107 -
Lower heater duct to floor outlet for Cougars or Mustangs with air conditioning. Used grade "B" part that will have minor defects. It will have cracks or chips. Almost half the price of the grade "A" piece and works awesome if you don't have one at all. Want to have directed heating, we've got you covered. Replaces Ford part number C9ZA-18C366-A.
Availability: In-Stock Item
Item #: 16140 -
Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.
Availability: Used / Wrecking Yard Item
Item #: 11-0444 -
Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...
Availability: Used / Wrecking Yard Item
Item #: 11-0145 -
Used driver side rear quarter window glass bracket, used for all 1969 and most of 1970. The later 1970 bracket had a D0Z... part number and used a different clip for attaching the window regulator. Good used bracket with all three plastic guides in perfect condition. This bracket is correct for Coupe and Convertible. Engineering # C9ZB-6529945-A Here is the 3M product used to glue the glass to the bracket. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install...
Availability: Out of Stock
Item #: 14208 -
Decent reproductions, but we suggest you consider our good used original FORD units that have been closely inspected for half the price! Replaces Ford part # C9ZZ-6530306-A. *NOTE* Originals were painted semi gloss black. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Out of Stock
Item #: 14170 -
Decent reproductions, but we suggest you consider our good used original FORD units that have been closely inspected for half the price. Replaces Ford Part #: C9ZZ-6530307-A. *NOTE* Originals were painted semi gloss black. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Used / Wrecking Yard Item
Item #: 20615 -
1969 Mercury Cougar and Ford Mustang convertible clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. *NOTE* Vertical chrome trim not include. Air conditioning cars were supposed...
Availability: Used / Wrecking Yard Item
Item #: 20618 -
1969 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. *NOTE* Vertical chrome trim not include. Air conditioning cars were...
Availability: Used / Wrecking Yard Item
Item #: 15431 -
1969 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and Cougar Ford part number...
Availability: Used / Wrecking Yard Item
Item #: 15427 -
1969 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number C9ZZ-7629700-A. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. Excludes...
Availability: Ships Direct from Supplier (Except International)
Item #: 15454 -
Excellent reproduction clear passenger side (right hand) glass for your 1969 Mercury Cougar convertible. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In...
Availability: Used / Wrecking Yard Item
Item #: 11-0147 -
Used passenger side rear quarter window glass bracket, used for all 1969 and most of 1970. The later 1970 bracket had a D0Z... part number and used a different clip for attaching the window regulator. Good used bracket with all three plastic guides in perfect condition. This bracket is correct for Coupe and Convertible. Engineering # C9ZB-6529944-A. Here is the 3M product used to glue the glass to the bracket. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly...
Availability: Used / Wrecking Yard Item
Item #: 15428 -
1969 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part number C9ZZ-7629700-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. This unit will not fit...
Availability: Used / Wrecking Yard Item
Item #: 15432 -
1969 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # C9ZZ-7629701-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear corner. Excludes coupes. Do you have...
Availability: Ships Direct from Supplier (Except International)
Item #: 15455 -
Reproduction passenger side (right hand) green tinted quarter window glass for the 1969 Mercury Cougar. This tint was called "Sun-X" tint and was an option on Cougars of this era. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is...
Availability: Used / Wrecking Yard Item
Item #: 11143 -
1969 Mercury Cougar and Ford Mustang convertible factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Vertical chrome trim not include. *NOTE* Air conditioning cars were supposed to have...
Availability: Used / Wrecking Yard Item
Item #: 11144 -
1969 Mercury Cougar and Ford Mustang convertible factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Vertical chrome trim not include. *NOTE* Air conditioning cars were supposed to have...
Availability: In-Stock Item
Item #: 16192 -
Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.
Availability: Used / Wrecking Yard Item
Item #: 11-0140 -
Used lower quarter window bracket for any 1969-70 Mercury Cougar and Ford Mustang non-fastback. This is the lower bracket that mounts to the bottom of the stationary slider bracket. This bracket adjusts the top movement in and out of the rear seat glass. Power or manual crank, hard top or convertible, driver or passenger side. Minor variation on this bracket, some are flat, some have a curve in the vertical edges on both sides. One bracket per window, same for either side. Replaces Ford part...
Availability: Used / Wrecking Yard Item
Item #: 11-0153 -
Used driver side (left hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with manually operated quarter windows. Nothing beats or fits like original FoMoCo! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Used / Wrecking Yard Item
Item #: 11-0154 -
Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with manually operated quarter windows. Nothing beats original FoMoCo! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...
Availability: Used / Wrecking Yard Item
Item #: 11-0285 -
Used roller for any 1969-70 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Often times one of the little branches breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the center of the rivet and using a tap, cut threads into the hole of your desired machine screw or bolt size. Re-install with a washer and you are done.
Availability: Used / Wrecking Yard Item
Item #: 11-0307 -
Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part number C9ZA-19618-A
Availability: Used / Wrecking Yard Item
Item #: 11-0377 -
Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. This unit will ship as shown. Two different versions of these brackets are known. Difference is the position of the lower stop bracket the size and rubber bumper. All brackets come with rubber bumpers installed. We may substitute a new bumper for a missing bumper. We recommend a thorough cleaning and a liberal amount of Sil-Glyde grease or equivalent during re-assembly. Ford part # C9ZZ-6529753-A. Do...