All Available Parts - 1969 Ford Mustang

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Used driver side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561695 number possibly. Ford number D0ZB-6561695. ...

Not rusty or water damaged, hardware sold separately. Vinyl is often UV damaged. Please indicate what color you prefer and we'll try to accommodate, but there's no guarantee we'll have it.

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Good reproduction but our used unit is a better value and will clean up just as nice.

This special bracket gets glued to the windshield. Rear view mirror bracket gets mounted to it. Glass bead blast it or just use a wire brush and it is ready to go!

Rear seat bottom or lower cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number C9WB-7663120.*Note - Does not fit coupe or fastback.Lower frame measures 46" at it's widest point and 18.5" high This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat back or upper cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C9WB-7666700. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. Though these seem to fit in a 64-70 Mustang convertible, the correct engineering number that would...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Driver side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a 1970...

Used front license plate bracket for a 1969 Mercury Cougar or 1969-70 Ford Mustang. Grade B used, will either show signs of straightening or need some straightening. Still functional, likely will not have the rubber bumper installed. Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used front license plate bracket for a 1969 Mercury Cougar or 1969-70 Ford Mustang. Grade A used, Best available, may have a slight curve or missing paint. Rubber bumper may be missing. New rubber bumpers available.Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall

Trico brand wiper blade refills for 1969-70 Mercury Cougar or Ford Mustang with original wiper arms

This excellent reproduction windshield washer bottle includes the Ford logo on the lid ( C9ZZ-17632-A ) and part number C9ZF-17B613 stamped on the top of the bottle exactly like the originals. The tooling was made using the original Ford blueprints and nice original patterns. Blow Molded Plastic. There are two available reproductions

Original stainless wiper blade assembly, pulled right off of a 1969 Mercury Cougar. ANCO brand original marked Made in USA O. E. by ANCO. Sold individually, two per car, 16" rubber wiper blade not included. These are production line installed wiper holders, we very seldom have them in stock. Originals didn't easily allow the replacement of the rubber blades. Notice the metal flap keeper on each end for capturing the rubber wiper blade?

Used anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding. 

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

Used Under-dash Wiring Harness Plastic Cover / Clip for the 1969 and 1970 Mercury Cougar or Ford Mustang

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-70  Boss 302 Ford engines. 1969-70 Mercury Cougar Eliminator and Ford Mustang with G code 302HO engines. *Note - Excludes 289 / 302 / 351C / 351W engines. 

Used vacuum reservoir that mounts under the battery tray for factory tilt swing away steering columns.  Fits Cougar, Mustang, and Thunderbird. Single nipple tank, we also sell the double nipple tank for the 1967-68 tilts. Replaces Ford Part # C9ZZ-3E547-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

C9ZE-9425-D or C9ZE-9425-E Cast aluminum intake manifold used on all 1969 G code Boss 302 engines in a Mercury Cougar Eliminator or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-D or -E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-C. Has "Buddy Bar" cast into the bottom side.

C9ZE-6A360-A Very unique part and a component to the 'drag pack' option on the 428SCJ engines. This is an additional counter weight used on conjunction with the SCJ crankshaft, SCJ crankshaft balancer. Ford part number C9ZZ-6359-A.

Dual vacuum advance stamped with HP6. Original for 1968-69 428 Cobra Jet distributor with 4 speed. The outer nipple does work. Brass nipples in very good condition. Ford part number C8AZ-12370-E. 

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...

C9ZE-9425-A or -B Cast iron intake manifold used on all S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-A or -B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-A. Current date 8H14.*Installation Tip - A water heated aluminum spacer plate with PCV provision is needed for proper air cleaner clearance....

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. The C8AE-6316-C harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Used distributor clamp and bolt, for any FE Engine: i.e. 352 / 360 / 390 / 410 / 427-4V / 428 / 428CJ / 428SCJ built from 1958-1976. Bolt may be used, or new from AMK Products. Ford part number B8A-12270-A.

NOS front side marker lens for the 1969 Mercury Cougar or Ford Mustang

Used front side marker lens for the 1969 Mercury Cougar or Ford Mustang. This lens will be in good shape with no cracks or breaks.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 5L18, November 18, 1965.  Used 0.030 over bore 4.180" Ford 428 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351W engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C9OE-6015 casting. Dated 9J23, September 23, 1969. Picture may show item with damaged oil pan and crank shaft and pistons. When we have them in stock we will post the casting date or dates. Heavy, will require...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7L1, November 1, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 8B21, February 21, 1968.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

Used core dual point distributor, for 390 HiPo, 427, 428 engines. C5AF-12127-E, with the Autolite name. Technically this is a service replacement distributor with a 9L16 date. November 16, 1969. This one is missing the gear.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of C9OF-Z. Original Ford part number C9OF-12127-Z.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V engines with 3 or 4 speed stick. Core distributors will have correct stamping of C9OF-N. Original Ford part number C9OF-12127-N.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with S code 390-4V and automatic transmission. Core distributors will have correct stamping of C7OF-G. Original Ford part number C7OF-12127-G.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with S code 390-4V 3 and 4 speed manual transmissions. Core distributors will have correct stamping of C9AF-K. Original Ford part number C9AF-12127-K.  Current distributor is dated 9D11, or April 11, 1969.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with 428 Cobra Jet and automatic transmission. Also fits 428SCJ engines with C6 or automatic transmission (Code U). Core distributors will have correct stamping of C8OF-J. Original Ford part number C8OF-12127-J. We finally got another one in stock, this one is dated 8M13 or Dec 13, 1968.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with 428 Cobra Jet and 4 speed manual transmission. Also fits 428SCJ engines with 4 speed stick. Core distributors will have correct stamping of C8OF-H. Original Ford part number C8OF-12127-H.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with G code Boss 302. Core distributors will have correct stamping of C9ZF-B. Original Ford part number C9ZF-12127-B.

Used core distributor for 1969-70 Mercury Cougar and Ford Mustang with G code Boss 302 engine. Core distributors will have correct stamping of C9ZF-E. Original Ford part number C9ZF-12127-E. No vacuum advance included. Current distributor has a date of 9J8, or Sept 8, 1969. Early 1970 build date.

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

NOS side marker / rear reflector for the 1969 Mercury Cougar or Ford Mustang.Part of Ford part #C9AZ-15A201-C My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our...

Set of 14 used instrument cluster sockets. These sockets are found on the backside of your instrument cluster and take a 194 bulb.

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A.NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

C9ZZ-14A318-A-Used Wire lead for the accessory terminal found optionally on 1969-70 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire can be marked with C8OB-14A318-A or C9ZB-14A318-A. NOTE: There are two version of this wire, one is long and the other is short. The shorter version has a smaller gauge wire. ...

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

Reproduction group 27 battery heat shield that fits many Mercury Cougar and Ford Mustang applications from 1967-70, on most hi-performance engines. It was often the first part discarded but serves a real purpose. Nice American made part, stamped with Ford numbers C7ZB10A682B and C7OB10A682B. There is also a D0... sized for group 24 heat shield offered for 1970-73. *Trivia - these battery heat shields were often trimmed down to fit group 24 batteries.Click on the link below to find some...

Used battery clamp to inner fender apron "L" bracket for 69 - 70 Cougars and Mustangs.This bracket secures the battery clamp to the inner fender apron. Ford Part # C9ZZ-10A705-A

Good used group 27 tray for 1969-70 Mercury Cougar or Ford Mustang. Assembly line installed group 27 battery tray. For those that want to keep it very original.Current tray has some erosion on the battery surface from use as shown. One little rust hole in the corner.

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. 1969 had a weak design and the release levers were prone to bend and break off. 1969 used a T shaped chrome release handle and 1970 used a black plastic T shaped release knob, which generally aren't interchangeble. Seldom in stock, please check out the reproduction version.

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

NOS brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Used drum brake distribution block for Mercury Cougar and Ford Mustang with front drum brakes. This unit mounts to the driver (left hand) side fender apron with a single bolt. Bare block without the brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available. Ford part # C8ZZ-2B257-B. Check out this video

Pair of reproduction firewall to shock tower braces for the Mercury Cougar or Ford Mustang. These Chinese made units are already painted black, so the only thing you need to do is bolt them on. However, we highly recommend that you get our superior quality used FoMoCo units right here!Replaces Ford part #'s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand). ...

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.