All Available Parts - 1970 Mercury Cougar

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Nice reproduction of the 1970 - 1973 front adjusting bracket for the 351 Cleveland engines. These do not have any markings.

Stamped steel bracket for mounting the power steering pump. Ford called this bracket the 'power steering pump adjusting bracket'. For any 1970 Cougar or Mustang with 351 or Boss 302 engines, additionally Mustangs with F code 302 V8 engines too. Note the larger "U" shaped fitting to fit the 1970 only larger pressure port. A small spacer was used when installed without air conditioning.

Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...

Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...

Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...

Metal stamped brackets used to mount the radiator on saddle mounts styles only. Rubber insulators not included.Check out our video on Radiator and Fan upgrades below:

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.These brackets came in two configurations, most has the round mounting holes but some were punched square. Not for use on...

Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...

BECAUSE THIS IS NOT AN ORIGINAL FORD PRODUCT, WE CANNOT RECOMMEND THIS ITEM AND NO RETURNS WILL BE ACCEPTED Shroud assembly includes custom mounting, wiring harness, and adjustable thermostat. High temperature resistant plastic with high performance electric fan to produce maximum cooling efficiency. This unit will also increased fuel economy and horsepower.  2550 CFM Fan with 30 AMP draw.  Dimensions (in inches): 15 3/4 x 26 1/2 x 3 7/8  including mounting flanges on...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

C8SE-A 1. 1969 application is very early production (before 11/6/1968) 351 engines with the 20 inch radiator. 2. 1970 application - 351 engines with manual transmissions and 20 inch radiator. Fan description - 4 blades and 17-9/16 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9OZ-8600-B. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C8SE-B Applications: 1. 1968 289-2V engines with air conditioning or the extra cooling package. 2. 1969 Boss 302 Eliminator - after 4/14/1969. 3. *1970 Boss 302 Eliminator. 4. *1970 351 with or without air conditioning. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B. Multiple dates available. *Note - 1970 Boss2 and 1970 351 owners, some time soon after the start of the year the exact same fan, but with casting number D0ZE-B was used. Check out...

This new for 1970 bracket, is also to be used in conjunction with the all steel "C" shaped pump mounting bracket. Not to be confused with the 351C or Cleveland bracket. The engineering # stamped on the part is D0AA-3C511-D and the MPC lists the part # as D0AZ-3C511-A. This is a rather hard part to find as most 1970 - 1971 Cougars came with the 351c. If you have any of these for sale or trade we would like to hear from you. For restoration purposes, this bracket was factory painted satin black. ...

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

Replaces Ford Part # : C8OZ-3C511-B

Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...

D0TA-C Application is for most 1970 428 Cobra Jet engines without air conditioning, and most 428 SCJ engines. According to the excellent website 428cobrajet.org there are instances of some early 428CJ and 428SCJ engines using one of the other two Cobra Jet fans. See C9ZE-E or C9OE-H fan listings. Fan description - 7 blades and 18 inches in diameter. Ford master part number D0TZ-8600-B. Stamped D0TA-8600-C. Current fan in our inventory has a date of K72, or October 1972. This would have been...

Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C9ZZ-8600-C. This fan will...

Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...

Heavy Duty reproduction fan clutch that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.707 inches. About 5/32" taller than our standard duty fan clutch. Please make sure that you have the clearance behind your radiator.  Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino,...

C7AE-D, Fan description - 5 blades and 18 inches in diameter. Ford master part number C7AE-8600-D. These 5 blade flex fans usually came on full sized Ford and Mercury cars starting in 1967. Can be used on any engine with the proper spacer with fan shroud with adequate fan opening. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C9OE-A radiator cooling fan. Multiple applications over the years. 4 blade fan, 14 inches in diameter. Not sure when these actually started being installed on the assembly line if at all. The C6AE-E version was used well into 1972 or later. Ford part number C9OE-8600-A. *Note - Excludes integral air conditioning. **Note - 1973 there is a note in the MPC that states this fan may be marked C9OE-A. Check out this interesting video where they test the efficiency of factory style and...

Replaces Ford part # C8ZZ-8146-A. This is a good reproduction made from the original Ford tooling but does not have the original part number or FoMoCo lettering. Has a smooth texture (unlike original) but it is made from a more durable plastic material. This is for the 24" radiator only. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

This is an excellent reproduction made from the original Ford tooling and features the original Ford logo and part number. This is for the 20" radiator used only in 1970. It weighs 1.82 pounds which is slightly heavier than the one sold Ford when they went obsolete in the mid 1990's. Replaces Ford part # D0ZZ-8146-B. 21" center to center mounting width12" center to center top to bottom mount Overall height 19" For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...

This is a good reproduction made from the original Ford tooling and features the original Ford logo. This is for the 24" radiator used in both the 351 Windsor and 351 Cleveland in 1970 only. Made of a different material than original and is 1.76 pounds VS. 2.56 pounds on the NOS shroud. *NOTE* This has the BARNUM BROS. FIBRE CO. INC. scratched off (but still faintly visible) just like our NOS shroud. Replaces Ford part # D0ZZ-8146-A. For some helpful tips on upgrading your Cougar (or Mustang)...

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap.

These are O.E.M. replacements and will not fit most after market radiators.

Keeps the corrosive agent in your coolant from destroying vital engine components

Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

Usually ships in 3-5 business days. This is the replacement for the factory radiator for Cats without Air Conditioning. If you have the Cleveland motor, we highly recommend going with the 24" radiator as it does a much better job of keeping your cat running cool. Not sure if you have a Cleveland motor? Click on the second image above to see a picture of the tell-tale of the 70 Cleveland. It has a unique coolant return line. For some helpful tips on upgrading your Cougar (or Mustang) cooling...

For the 1967* - 1969 FE / Big Block Cougar and Mustang and 1970 351c & 351W with AC and or heavy duty cooling package.  For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat.  Before you buy fancy wheels, valve covers or most anything else (except brakes) this should be at the top on your list.  Many applications only call for a 2 core but we...

Sometime during the 1970 model year, this bracket was used on cars with 24 inch radiators. At the beginning of the year the 1969 bracket was being used. Pretty much indistinguishable when mounted on the car. When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is...

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Reproduction overflow hose with smooth outer wall. Hose length 36"

Used FoMoCo 24 inch small block radiator. This is for a 1970 Mercury Cougar or Ford Mustang with 351-2V or 351-4V and FMX (automatic code X) transmission. 351 engines only with lower radiator hose connection on the driver side. Putting the lower outlet on the driver side was new for 1970. Check your water pump outlet if you have a 351W engine. Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Lower tank does have the connections for...

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

195 Degree Thermostat for the 351C, 351M or the 400. Factory spec temp for these engines is 192 degrees. Properly blocks off port that recirculates the water through the engine.

Correct head-stamp. 

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. Replaces Ford Part #: D0ZZ-8592-A.

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

Reproduction aluminum cast A356 water neck for FE Big Block engines. Made from original factory blueprint, and includes the correct stamping. Will fit the 67 Big Block, but markings are correct for 68. Replaces Ford Part #: C8AE-8592-B.

Aluminum casting, made in the U.S.A. Exact copy of original, including part numbers. Fits any small block Ford 260/289/302/351W but would have only been correct on 1967 Mercury Cougar and 1965-67 Ford and Mustang with 289 engines. Has natural cast finish as original. Does not have the provision for the thermal vacuum switch starting in 1968 and newer small block Ford V-8 engines. Replaces Ford Part #: C5OE-8592-A For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...

These bright beautiful reproductions replace those corroded and rusty originals that just look nasty. Replaces Ford Part #: C8AZ-18599-C

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

Adhesive-Backed Gasket Material Helps Prevent Breaking of Water Outlet. Gasket Cement is Not Needed. Self-Adhesive Backing Holds Thermostat in Place While Water Outlet is Being Installed.

Thermostat Housing Gasket BY FEL-PRO® for the 351 Cleveland.

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

This elbow is zinc plated for years of reliable service and is for 351, 390, and 428 engines. Replaces Ford Part #: D0AZ-18599-A.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Reproduction concours correct premium thermostat for the 351C. This is the correct thermostat you would use in conjunction with the new concourse restrictor / by-pass plate on 70 - 73 Cougars and Mustangs equipped with a 351 Cleveland engine. This is a the assembly line style thermostat.  Replaces Ford part number D0AE-8575-B.

Used aluminum water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum finish. Comes with threaded hole for either a screw-in cap, or thermal switch. For use with common 2-1/8 inch thermostats. Correct for 1968-70 FE engines. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. Additionally, we notice that the threads get a bit rotted out where the thermal switch...

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.

OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.

Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. Sold individually, or in a set of 4. 1/2 inch hex head size an the threads are 5/16-24. This bolt is approximately 7/8" to the shoulder and 1-1/8" in total length.  Replaces Ford part # 380288-S. ...

Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. 1/2 inch hex head size. Threads are 5/16-24. Also sold individually. These bolts have an approximate length of 7/8" to the shoulder and an approximate overall length of 1-1/8". ...

Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. One bolt with captured split washer. Also available in a set of 4. ...

Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. Four bolts with captured split washers. Also sold individually. ...

New water pump plate gasket for the Mercury Cougar or Ford Mustang.

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.

This USED shroud was discontinued by Ford in the mid 1990's. It really is no different in appearance from our reproduction, but it does weigh a hefty 2.56 pounds and the reproduction weighs 1.76 pounds. Must have FoMoCo / part numbered shroud for that show quality BOSS 302 or 351C Eliminator. Just like our reproduction, the BARNUM BROS. lettering has been ground off. This was done because Barnum no longer made the shrouds for Ford in the latter years, but the tooling still had their name on...

Water By-Pass Hose for 351W engines with Autolite® logo and part number imprinted in white ink. Stamped with C9OE-8597-D. This would be correct for Mustangs and other Ford or Mercury with 302 engines in 1969. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Silver zinc finishDiameter 5/8"Fitting 3/4"

New water restrictor plate for the Mercury or Ford equipped with the 351 Cleveland engine. It has been an accepted fact for decades now that the 351C bypass system was not the greatest idea Ford ever came up with. The unique 351C thermostat "hat" never seals well, causing a certain portion of coolant to just circulate through the block and never make it to the radiator. Years ago, Pantera enthusiasts (all Panteras had cooling issues from the factory BTW) found that if they soldiered a penny...

New water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum without casting marks, sand cast finish. Comes with screw-in cap in place of the thermal switch if you like, includes gasket. For use with common 2-1/8 inch thermostats. *Note - very early 1967 cars were still using the 2-1/2 inch thermostats. Cutoff was around November 1966.

New water neck or thermostat housing for all 1967-70 Mercury Cougars or most other Fords with 289/302/351W engines. Cast aluminum with a shiny finish as shown. Removable plug for use with thermal vacuum switches. Comes complete with gasket.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part. Check out this video

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

NOTICE: The supplier is no longer making the previous version of the upper hose, and the new hoses will have more of a textured outer wall.  Some Vendors show C8ZE for the upper hose, but C8WE is the correct stamping. These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal...

These are the best CONCOURS radiator hoses on the market. Made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Features special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct including Autolite logo. Hoses are also approved by Ford Motor Co. Replaces Ford Part #: D0ZE-8B273-B &...

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. NOTE: Dwayne from "The Brothers Car Collection" clued us in to the fact that the choke tube fitting on the passenger side is indexed 180 degrees off on some sets we sell. Fortunately you can carefully spin it around with vise grips so the opening faces...

Reproduction 428 Cobra Jet Exhaust Manifold Spacer 1968 - 1970 Mercury Cougar, Ford Mustang, Shelby and Torino Repro

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. These manifolds are available in both early and late versions. The earlier version manifold has the correct spacer on the right side while the later version manifold does not.  Installs easily and eliminates clearance issues compared to headers....

Exhaust Manifold Choke Stove Rebuild Kit for All Small Block and Big Block Engines 1967 - 1973. Includes Stainless Steel Mesh Filter Element and Choke Stove End Cap Fitting.

Basic kit for rebuilding your Ford Autolite or Motorcraft square bore 4300 or 4 barrel carburetor. This kit is not for later spreadbore carburetors. Spreadbore carburetors have much larger secondary venturis. See picture.

Basic kit for rebuilding a 1967-70 Holley model 4150 4 barrel carburetor. Includes illustrated instructions. Holley packaged renew kit. This kit is not for model 4160 or other Holley carburetors. See pictures of Holley 4150 below. Click on images to enlarge. ...

Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

C9OE-9431-B 351W factory original cast iron exhaust manifold for driver side. For all 1969 and 1970 Windsor 351's.