1967 Ford Mustang

(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...

Manual transmission clutch throw out bearing for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is with a 10 inch disc.

Sold as pair, exact copy. These also double to keep your windlace firmly in place.

These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications. Pertronix Model 40011.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Used coil mounting bracket. This is the Big Block V-8 version starting 1967-69. Found on 390 and 428CJ cars. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. This version is for big block V-8's, and has an additional 'C" channel bracket on the bottom, later versions had an removed thel reinforcing 'C' channel on the bottom. Later version started in...

Used coil mounting bracket. This version of the bracket is probably the most common. Typically this version was used on small block V-8's in 1967-68. This version has the 'rails' to give it strength. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

Used driver side coil spring cover, taken from a parts car. Ford part # C7ZZ-3383-A.

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.