All Available Parts - 1968 Mercury Cougar

Good used rear window with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available as each piece differs. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded...

Used anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding. 

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 390-2V or 4V engines. Updated design from the originals, fuel lines fit the same.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C5ZZ-9327-A.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

NOS stainless steel, carburetor deflector gasket for W code GT-E 427-4V engines.  Order of installation: Open gasket #15292, SS plate #31256, Phenolic spacer #41936, paper gasket #11813, Holley 4088 carburetor. Ford part number C8AZ-9A589-C,  Engineering number C8AE-9A589-E This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used plastic clip for the Mercury Cougar or Ford Mustang.

Factory used exhaust tip from a 1968 Mercury Cougar GT-E. Fairly good condition, has some scuffing on the lips of the tips and or scuffing on the bottom edge. Factory stamped C8WX-5C262-A. A 20% discount for purchasing a pair. 

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

C7AE-9425-F Cast aluminum intake manifold used on all 1968 W code 427-4V engines in a Mercury Cougar GT-E or 1968 Ford Mustang Shelby GT-500 (non KR models). Stock 4 barrel intake manifold. Take off manifold with correct casting number of C7AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-H. *TRIVIA* This is also known as the PI aluminum intake manifold, PI = Police Interceptor. ...

All of our used insulation hood pads are guaranteed to be filthy dirty, less than perfect (as shown) and include at least one spider. We cannot fold these to ship them and they are too large for UPS. You must pick them up in person or we can ship them for free when you purchase a hood from us.

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Dual vacuum advance stamped with HP6. Original for 1968-69 428 Cobra Jet distributor with 4 speed. The outer nipple does work. Brass nipples in very good condition. Ford part number C8AZ-12370-E. 

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering are dated 8-67, 6-68, 5-68, 7-69, 8-69. Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is...

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

C7TE-9425-G Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used before 1-9-1968. Take off manifold with correct casting number of C7TE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-P. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

C8TE-9425-A Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used after 1-9-1968. Take off manifold with correct casting number of C8TE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-R. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

Used distributor clamp and bolt, for any FE Engine: i.e. 352 / 360 / 390 / 410 / 427-4V / 428 / 428CJ / 428SCJ built from 1958-1976. Bolt may be used, or new from AMK Products. Ford part number B8A-12270-A.

1968 Mercury Cougar and Ford Mustang J code 302-4V with automatic transmission.Ford part number C8ZF-12127-D.

This is a used distributor for the 427 4V W code engine found in 1968 Mercury Cougars equipped with automatic transmissions.Ford part # C8OF-12127-G.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory J code 302-4V V-8 engine. Rated at 230 Hp with 10.0:1 compression ratio in 1968. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil pan are included...

Used Distributor / 302-4V / Manual Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8ZF-12127-A  

Used Distributor / 302-4V / Automatic Transmission for the 1968 Mercury Cougar / 1968 Ford MustangFord part number C8ZF-12127-B  

This is a used distributor for the 1967 Mercury Cougar or Ford Mustang equipped with the 390 4V engine. It was also used on the 1968 Mercury Cougar GT-E equipped with the 427 4V engine.Application is 1967 automatic with smog, and 1968 automatic with Thermactor smog system. Check out this video

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 5L18, November 18, 1965.  Used 0.030 over bore 4.180" Ford 428 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

Great condition used pair of taillights that includes two grade "A" bezels and two used grade "A" lenses with backing plates. We've taken the time to polish the lenses and they will have no cracks. The bezels will have good chrome, good paint and no pitting. This is as good as they get! *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 7M16 or December 16, 1967. This item cannot ship through...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K4 or October 4, 1966.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 7l17 or November 17, 1967. This item cannot ship through any...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7L1, November 1, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 8B21, February 21, 1968.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

Featured in this kit are all the basic items you need to convert your small block 1967 - 1968 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small...

Power wire that connects the PRNDL or shift indicator illumination lamp assembly, and the main under dash wiring harness on all standard 1968 Cougars and Mustangs. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8ZZ-15A808-A. Has red colored bullet plug to main harness, and blue plug to PRNDL wiring. Fits 68 CougarFits 68 Mustang

New Old Stock front turn signal lens for 1967-68 Mercury Cougar.  Sold individually, two required per car. This is a factory clear lens for the Cougar, which used an amber light bulb. Mustangs used an amber lens and a unfiltered light bulb. Screws sold separately, you can find them here. Replaces Ford part # C7WY-13208-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Original OEM light found on 1968 XR7-G and early cars and later recalled. EXACTLY 100% correct with the right serial numbers in the right places as per the blueprints from Shelby American: * IGM 1642 PN on the bottom right * K11123 N14 cm AUF 5m up the right side * No numbers on left side Marchal made several versions of this light, only this one is the correct one for your 1968 Cougar or Shelby Mustang or California Special (GT/CS). It has the famous 'cat eyes' internal diffuser. Dual...

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.

Used backup / reverse light for the passenger side (right hand) of the the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Perfect inexpensive replacement item for those wanting to keep their car all original and match the overall patina of their low mile car. Casting number as seen on the back side reads C7ZB-15515-A.Replaces Ford part #...

Used backup / reverse light for the driver side (left hand) of the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Casting number as seen on the back side reads C7ZB-15A509-A. Replaces Ford part # C7ZZ-15512.

This XR7-G Lucas Square 8 light is in average condition with pitted glass, missing plug ends, and pitted spacers. *NOTE* The lens shown is actually mounted upside down for Cougar use.

Reproduction halogen headlight conversion kit. Included in this kit are the four halogen headlight bulbs (2 high and 2 low) and the full relay kit, which is needed when installing halogen bulbs on your 67 - 68 Cougar. The 55 Watt Xenon Halogen H4/9003 bulbs included in this kit are "cool white" which have a bit of a blueish tint, like you see on modern cars. If you would like to go with a more original "natural white" color, you can buy these inner replacement bulbs. NOTE: YOU MUST BEND THE...

Good used pair of taillights that includes two average grade "B" bezels and two used grade "B" lenses with backing plates. No obvious cracks in the lenses but there will be stress cracks that will only be found under close inspection. The bezels will have good chrome with no obvious defects but the paint will need attention. This is a good saving over buying the four or six parts individually. Don't forget to pick up a set of gaskets for the lenses as they always are needed after 40 plus...

Headlight relay kit converts the 1967-68 Mercury Cougars with quad or 4 headlights to modern car technology (kit also works on 1967-68 Mustang 2 headlight systems). If your Cougar suffers from dim headlights you are not getting a full battery power to the back of your headlamp bulbs. Safe for use on our vintage cars. Still uses your headlight switch. Instead of carrying reduced voltage to the headlights through the switch, the switch triggers the relay, which takes power directly from the...

We really cannot justify the average guy buying these over our quality reproduction pair. Only the most tedious of restorations would benefit from having this levels of detail. Sold as a pair, Ford part #: C5ZZ-13206-B for the passenger side and C5ZZ-13207-B for the driver side.

Ford sold service replacement taillights as a complete unit that included the backing, chrome and lens, just the lens or just the chrome. This listing is for one complete taillight unit as shown. Sold individually, two required per car. Ford part number C7WB-13440-A *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Complete used setup as shown, you will get the actual set shown in these pictures. This unit was taken from a low mileage wreck decades ago and carefully stored indoors. Every gauge and switch has been tested. This grade A setup is perfect for that low mile GTE, XR7G or GT that is unrestored and deserves OEM as opposed to restored or reproduction. We can often give you credit towards your incomplete or broken xr7 dash parts that can be refurbished. Notice how nice the woodgrain is on this one....

NOS 1967-68 Mercury Cougar XR7 speedometer with trip meter. Original unused speedometer in FoMoCo box, all numbers at zero.  Ford part number C7WY-17255-C

Used 1967-68 Mercury Cougar XR7 speedometer with trip meter, grade A condition. Grade A will be fully functioning, and good legible numbers on the trip meter portion. We also see grade B XR7 speedometers that have cosmetic problems, usually on the odometer or trip numbers.Ford part number C7WY-17255-C Put your desired odometer range in the comments section, and we will try and match it up as close as possible. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

There are five of these on the RH side that hold your plastic dash to the metal understructure. These also hold on the map light. Sold Individually. Ford Part #: 376642-S. Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting things...

Guaranteed to work good. If your gauge is cosmetically fine you may consider purchasing our grade B version and using your existing gauge face as they are easy to change out.

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Mini Tachometer that fits in the small center clock opening. This easy to install three wire tachometer looks OEM but as you probably know, Mercury never offered an in dash tachometer from the factory. Just remove your current clock or dummy plate and this unit installs from the backside in its place. If you are returning a core dummy plate for credit it must have good cosmetic appearance. When you send your core for credit, please be sure to include a copy of your sales receipt. Check out the...

Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...

NOS brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

C9OZ-2211-C Right hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70866. Originally manufactured by Bendix part number 319481.

C9OZ-2212-C Left hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70867. Originally manufactured by Bendix part number 319480.

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

This listing is for the momentary rocker switch that operates the power sunroof on the 1968 XR7G and is located in the center console. This is actually not the correct switch as you will notice by the pin / wire configuration on the back. This "substitute" switch was taken from another model from the day such as the Lincoln Mark III rear seat quarter window switch.Please note the comparison pictures original vs. "other".1968 Cougars equipped with a power sunroof that were not an XR7G...

Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.

This is a reproduction of the original service instruction decal that was located on the side of the air cleaner.Fits the following models:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

This is a reproduction of the original decal that contains the word "FRONT" that was located on the front of the air cleaner.Fits the following models 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang ...

This is a new, faithful reproduction of the rarely seen promo sticker that was created after the 1968 Cougar won Car and Driver magazine's Readers Choice Poll for Best Sporty Car. The winners were announced in the May 1968 issue. These were mostly put on the quarter window glass, but it's up to you where to show off your Cougar's status. This new decal is the same size as the original (2-3/4" x 3-3/8") and printed on mirror-shiny vinyl. The main difference is that the adhesive is on the back...

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

Used drum brake distribution block for Mercury Cougar and Ford Mustang with front drum brakes. This unit mounts to the driver (left hand) side fender apron with a single bolt. Bare block without the brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available. Ford part # C8ZZ-2B257-B. Check out this video

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

This quality kit contains everything you need to replace the original hardware for fuel and brake lines on your 1968 Cougar or V8 Mustang. It even includes 3 new bolts for the metal protector plate for the fuel line near the left rear wheel. Most of the mounting locations can be seen below: Click on images to enlarge. ...

Good used solid panel with all parts removed. Panel measures 19.5" x 39". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.

NOTE: We only sell these on an exchange basis and you must send your core in advance. Keep in mind that none of the used motors we have on hand will have the correct plugs in place (they will be bare wires), if your core has the plugs we can switch them over, also, you should remove the 4 rubber insulators before you send your core in, our units DO NOT have them installed.Good used motor taken from 1967 through 1970 Cougars. Motor has been taken apart, cleaned, serviced and...

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...

Here is our used lower rear window channel which we will cut to suit your needs. Quite often vinyl tops will cause rust in this area and this part is cut from a rust free Western parts car. If you need the package tray attached there is no extra charge, but shipping costs will increase. We usually cut generous into the quarters and several inches up the sides of the rear glass. If you only need one side contact us as we can help.   ...

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate. In late 1968 390-427-428 Mercury Cougar and Ford Mustang came with this reinforced tower due to a problem they were having with structural cracking. No specific part number for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

Good used, rust free valance that will have minimal prep time to be paint ready. Getting to be hard to find without excessive filler. If you have the optional rear bumper guards then you will want a valance like the one pictured that has the factory holes for them. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. Ford part # C7WY-6540544-A.

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate.The reinforced shock towers came out in late March 1968 and were used on all big block Cougars and Mustangs. 390-2V / 390-4V / 427 / 428CJ. No specific part number exists for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Good used, rust free valance for the 67 - 68 XR7G Cougar that will have minimal prep time to be paint ready. Getting to be hard to find without excessive filler. If you have the optional rear bumper guards then you will want a valance like the one pictured that has the factory holes for them. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. Ford part # C7WY-6540544-A.

New old stock, This unit is also known as a bumper filler, rock guard, or filler panel. Fits any 1967-68 Mercury Cougar.Ford part # C7WY-17779-A.