All Available Parts - 1968 Mercury Cougar

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, kind of shaped like the State of Arizona, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, kind of shaped like the State of Arizona, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502666-A.

Used bracket for mounting the front valance on any 1967-68 Mercury Cougar. L shaped bracket connects the lower valance, stone guard, and inner bumper bracket. Two per car, sold individually.Ford part number C7WB-17A986.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Used pair of diagonal support / stabilizing brackets for the 67 - 68 Cougar. The bars are located behind your back seat and help with stabilizing the car and to prevent the body from torquing or twisting. For added support we recommend installing our seat divider panel. These brackets will be cut out of a scrap car and sent to you as is and will need to be trimmed and cleaned up for paint. Check out our video on front suspension and chassis upgrades below: ...

This is our used driver side (left hand) upper rear fender brace. Welds to the upper cowl on any 1969-70 Mercury Cougar and Ford Mustang Ford part number C9ZZ-16A005-A driver side, C9ZZ-16A006-A passenger side.

Round hood latch dowel that screws into the hood on all 1967-68 Mercury Cougars. Threads are 1/2-13, dowel assembly includes threaded dowel, jamb nut and washer as shown.Fits many other Ford products, see list below.Replaces Ford part numbers C4ZB-16929 and C5ZZ-16929-A.

Hood latch striker that screws into the hood on all 1967-68 Mercury Cougars. Ford calls this a Plate - Hood Auxiliary Catch Striker.Fits many other Ford products. You can find the bolts for this item here. Replaces Ford part numbers C5AB-16918 and C4DZ-16918

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just 1/8" longer on the side that actually holds the visor tip. This unit is only available in black or neutral. We have most other unfaded colors in used. This item works for 68 Cougar Coupe, 68 Mustang Coupe / Convertible and 71-73 Cougar Convertibles. Replaces Ford Part # C8ZZ-6204132, C8ZZ-17690 OR...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

Reproduction one year only switch for the 1968 Mercury Cougar with power sunroof (or 1968 Ford Mustang convertible). The XR7 G used a different switch built into the console but the other Cougars ordered with a sunroof in 1968 had this switch mounted to the right of the steering column under the dash.   Knob and bracket included as shown.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

Our Grade "B" 1967 - 1968 front fender extensions almost always have the damage centered around the "tip" as evidenced by the one you see pictured. We will not send you junk, but rather a part needing only minor attention. Notice the portion behind the eyebrow is painted black from the factory. Used hardware is often available for free if you mention it. Do not over tighten this part as they are soft metal and warp easily. Ford casting number as seen on back reads C7WB-16019-A. Do you have...

Our grade "A" fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Ford part # C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

Very rare to find one of these that has never been tapped in the slightest. We have a very limited quantity of grade A centers in stock. Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

The majority of our centers look like the rust free part you see pictured. They will need some minor body work before paint. We will not send you junk! Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527703-A, Mercury MPC # C7WY-6528073-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs only minor repairs to be show quality.  Ford part # C7WB-6527703-A Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs only minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C7WB-6527702-A, Mercury MPC # C9WY-6528072-A. Do you have questions about your Cat's factory...

Our grade "A" 1967 - 1968 fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Hardware not included but if you ask for it we will try to include it at no charge. Note that the inner part just behind the eyebrow moulding is painted black from the factory.Ford casting number as seen from the back side reads C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this...

Our Grade "B" fender extensions almost always have the damage centered around the "tip" as evidenced by the one you see pictured. We will not send you junk, but rather a part needing only minor attention. Ford part # C7WB-16018-A.

Reproduction Driver side fender extension. This latest in a series of 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16". NOTE - This splash shield does not come with the rubber, but you can find the seal kit here. Replaces Ford part # C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. ...

Reproduction Passenger side fender extension. This latest in a series of 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16". NOTE - This splash shield does not come with the rubber, but you can find the seal kit here. Replaces Ford part number C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. ...

New Old Stock passenger side fender extension for the 67 - 68 Cougar.  Ford casting number as seen from the back side reads C7WB-16019-A.

New Old Stock driver side fender extension for the 1967 - 1968 Cougar.  Ford casting number as seen from the back side reads C7WB-16019-A.

Complete floor pan for the 1965-68 Ford Mustang. NOTE: Can be made to fit 67-78 Cougar, Included seat risers are Mustang versions, which are taller than the Cougar seat risers. We recommend re-using your original Cougar seat risers, unless you want the extra height of the Mustang risers. Also note that the risers included with this floor pan will not be attached, you'll have to weld them on. Keep in mind Cougar has a longer wheel base which make the portion under the back seat substantially...

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

This piece runs under the floor over the transmission where the floor pan meets the firewall.

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

New inner floor frame support for the Mercury Cougar and Ford Mustang.

Reproduction floor pan firewall extension for the driver side (left hand) of your 67 - 68 Cougar.

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Looped weld in retainer for the rear seat installation on any 1967-70 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets. We think that the Ford number is C5AZ-6263370-B, but we have not been able to verify this for certain. For sure that basic Ford part number is 63370. ...

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

If you are buying our one piece Mustang floor pan or our driver side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

If you are buying our one piece Mustang floor pan or our passenger side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need the to have stapled rubber shields replaced. Same part as the 1967 piece, but with a section cut out for the marker light housing. A Mustang shield will not fit a Cougar because the fender has a much different contour. Supply limited due to the proximity to the battery.Ford part # C8WY-16A573-A.

This unit consists of a metal shield with rubber stapled to the edges mimicking the fender contours. In most cases, these used shields will need to have the stapled rubber shields replaced. Same part as the1967 piece, but with a section cut out for the marker light housing. A Mustang shield will not fit a Cougar Because the fender has a much different contour.Ford part # C8WY-16A574-A.

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

Reproduction Non-Functional hood scoop that was originally used on the 427 GT-E, but will work on any 1967-68 Mercury Cougar and look great! This scoop measures 25 3/8" at its widest point, 26-1/2" at its longest point, and is 2" high. Originally, the recessed scoops in the front were painted black to give the illusion of an open scoop. The original blue prints show the center of the rear stud as being 2 1/8 inches forward of the back edge of the hood. Measuring the distance on original XR7-G...

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

Non functional scoop originally used on the 1968 Mercury Cougar XR7-G but will work on any 67 - 68 Mercury Cougar. This scoop measures 25 3/8" at its widest point, 26 1/2" at its longest point and is 2" high. The original blue prints show the center of the rear stud as being 2 1/8 inches forward of the back edge of the hood. Measuring the distance on original XR7-G and GT-E's most measure about 1 1/2" from the rear edge of the hood to the rear edge of the scoop at centerline. This differs from...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Air cleaner intake assembly or snorkel specific to the one year only 390-2V premium fuel engine, (X code engine). This version has the thermally operated trap door. There was an early version that used vacuum to open the trap door to the heat stove. Ford part number C8WY-9A626-A. *Note - This snorkel has a different spacing on the mounting ears, it will not mount to a 390GT air cleaner base.

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our Grade "B" hoods will most likely have small rust holes along the bottom side or have small dents on the top side but they will...

THERE ARE NO RETURNS ON THIS PART. Not a good fit but you can make them work...You will have to elongate a couple of the small holes that mount the valance under the bumper, but not by much. Once mounted the part looks as though it was not made quite wide enough. We recommend purchasing our premium version, because honestly, you'll spend a lot of time trying to get this offshore reproduction to fit right.  Please do not call us and say you are disappointed with this part; we are telling...

This is a reproduction front valance for your Mercury Cougar. This valance is an excellent reproduction in every detail. Below are pictures of it next to a NOS valance for comparison sake. As you will see, this is an "A" class reproduction in every aspect. Rarely is a reproduction ever a match in any way to NOS. This one is an exception to the rule!Click on images to enlarge. The fasteners for the license plate are just slightly different but the function and placement are dead on.  These...

Best of the best in Western sheet metal! Just sand, paint, and install. This unit is also known as a bumper filler, rock guard, or filler panelFord part # C7WY-17779-A.

Price does not always dictate value... Our grade "B" stone deflectors have very minimal, easy to fix damage. The damage is most often found on the corners and would be hard to detect often times even if you chose not to fix them at all. Due to the flat, simple design of these stone deflectors most people with little or no experience in body work would be capable of making them look new again. We guarantee you will not find and rust (other than surface) and no signs of excessive filler. We have...

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

These reproduction hood latch catch bolts fit both the Standard and XR7.

Reproduction pair of 7/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

Reproduction pair of 1 1/8" long hood latch support bolts for the 1968 Mercury Cougar. Looking through cars with original parts, we've found a few different variations of the types of bolts used. It would be best to measure what you have and purchase the correct length bolts.

These are our reproduction hood and hinge bolts and nuts for your Mercury Cougar or Ford Mustang.

Here are our reproduction hood latch support brace bolts and U nuts for the Mercury Cougar.

These reproduction fender to pillar bracket bolts fit both the Standard and XR7.

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

These reproduction quarter panel end seal screws fit both the Standard and XR7.

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.

These reproduction fender shield to bumper screws fit bot the standard and XR7.

Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.

This is our reproduction fender fastener kit for you r Mercury Cougar or Ford Mustang.

Here are our reproduction fender to pillar bolts for your Mercury Cougar or Ford Mustang.

Here are our reproduction fender splash shield screws for your Mercury Cougar or Ford Mustang.

These are our reproduction fender splash shield screws for your Mercury Cougar or Ford Mustang.

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires rubbing. We really inspect the area where the fender extension bolts...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires rubbing. We really inspect the area where the fender extension bolts...

Late 1968 Mercury Cougar trunk lid, identified by having the large square hole for installing the trunk lock and latch parts. This style is hard to keep in stock, please see the 1967-68 version in the related section. Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that...