All Available Parts - 1967 Mercury Cougar

C6ZZ-6582-H Smooth chromed valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 DGS Mercury Cougar and optional on 1965-67 Ford Mustang with 289 engines. Ford master parts catalog shows a right and left version of this cover those numbers are C6ZZ-6582-H & C6ZZ-6582-J. *Note - This is a used chrome valve cover. The plating was pretty low quality back in 1966-67 and these will show rust pitting. For best results we recommend the painted version of this valve cover...

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This chromed push on oil cap was used on the DGS package or engine dress up kit which included chrome valve covers and air cleaner lid. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a Black painted version was also available on most 289 engines sold in California. This icon means that we're looking to buy...

Used oil fill cap for 1967 Mercury Cougar or Ford Mustang with 289 and California emissions. This black painted push on oil cap was on California sold cars with closed emissions systems. Identified by the vertical pointing elbow, for attaching a hose to the air cleaner base. Marked FoMoCo on the top inside a rectangle box.*Note - a chromed version was also available with engine dress up kits.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Includes drain plug.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

The oil filter made by the original Ford supplier.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Bushings for the clutch equalizer bar, ball pivot for 1967 through 1970 with big block engines only, sold as a pair. Replaces Ford Part #: C1AA-7543-A

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Used grade B / B+ trim ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 1968 SS wheel. This ring will have one or two very small scratches or dings that will not be very noticeable. We have various condition rings at a reduced price as well as an occasional NOS looking ring, call for availability, sold individually.Replaces Ford part number C6ZZ-1210-A.

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

Used clutch spring bracket that attaches to the brake / clutch hanging bracket. All 1967-68 Mercury Cougar and Ford Mustang with manual transmissions. Replaces Ford Part #: C7ZZ-7535-B.

Reproduction pair of brass 3/8 ID bushings for the clutch rod. Protects clutch equalizer and rod, and removes excess play.We also sell these in nylon. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it...

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. Includes both Pressure and Return hose that connect to the control valve. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against...

[No Description Provided]

Premium power steering hose kit for the 1967 Cougar or Mustang with a small block with a 1/4" control valve fitting.We highly recommend upgrading to the large nut (5/16") control valve as the small nut control valve poses a potential safety issue, thus the reason why Ford replaced it the following year. The small nut system was engineered dangerously close to the maximum psi tolerances of the crimp that holds the fitting on the tubing ...

Rear Valance Hardware kit contains 2 bolts, 2 clips and 2 nuts. "Almost" correct reproduction that functionally works great. Plated to prevent rust.See related items for a more complete fastener kit, which includes the pan head Phillips screws. Replaces Ford Part #: 372719-s100.

Reproduction Small Block Equalizer Mounting Kit for the 1967 - 1970 Mercury Cougar and Ford Mustang equipped with the 289 / 302 / 351. Includes stud. Also works for BOSS 302

The Ford Master Parts Catalog calls this "Bracket - Clutch Release Lever Retracting Spring". This little "L" shaped bracket is found only on 1967 - 1968 Mercury Cougars and Ford Mustangs with a 3 or 4 speed manual transmissions. When people part out early Cougars they often leave this little detail item behind not fully understanding its function or rarity. Stood on end its length at the very longest point is 3 1/4". Its function is to but tension on your equalizer bar when it is in its...

The pressure hose that connects to the power steering pump has industrial high pressure fittings.

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang with or without Power Steering Cooler.  Be sure to select the option to...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

The tubbing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find these at your local auto parts store or the the "Mustang Discount" folks. Replaces Ford Part Numbers: C7OZ-3A719-A, C7OZ-3A719-C, C7OZ-3A713-A, C7OZ-3A713-C, C7OZ-3A713-D. Please Note: We highly recommend upgrading to the large nut (5/16") control valve as the small nut (1/4") control valve posses a potential safety issue, thus the reason why Ford replaced it the...

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Installs between seat track and carpet. These are the same gauge steel as originals. Four per bucket seat, normally only seen on the 1967 model year, will need to be restored. Reproductions work fine, but look a little different. Ford Part # C5ZZ-13190-K

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

Water pump pulley 1 sheave, about 6.11 inches. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches. Application include 1967 Cougar with 289. 1969 Cougar and Mustang with 390-4V. Also various Mustangs 1965-67, all with 289.Replaces Ford casting number C5OE-8509-A.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

C6OZ-8509-A For any S code 390 engine without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single sheave pulley, 6-3/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford part number C60E-8509-C.

C6AZ-8509-C 390 engines with air conditioning. Power steering and or thermactor emissions allowed. 2 sheaves with a diameter of about 5-5/16 inches. *Notes say after 1-9-1967 engine build date. Ford casting number C6AE-8509-F.

C6AZ-8509-D Strictly California 390 Cougars without air conditioning. With or without power steering. 3 sheave pulley with diameters of both 5-11/16 inches and 6-1/8 inches. Ford casting number C6AE-8509-J.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

NOS Air conditioning belt tension pulley for Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968.  Ford part # C7AZ-8678-B. NOTE* Send in your old core for a credit toward the purchase of this NOS pulley. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

[No Description Provided]

Ford casting number C4ME-6A301-A. Single sheave outer pulley for use with power steering as the only option. This pulley is listed in the 1967 engine assembly manual. Listing is for 'Standard Alternator Drive with Power Steering'. Standard alternator would be a single pulley on a 42 amp rated alternator.

C5AZ-8509-J For use originally on 1967 289 engines without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single belt pulley 6.10 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.*This is one of the few water pump pulleys that did not have an imprinted casting number. Originally this pulley had an ink stamp. We will most likely be...

Air conditioning belt tension pulley for 1967 Cougars and Mustangs with the 390 engine. These are all sold with new bearings. If your pulley only needs a bearing, we have those too. Used with C7ZZ-2888-A, which is the steel lateral support brace for 1967 Cougars and Mustangs with the S code 390 engine. Two versions of this pulley were made by Ford, the difference is the pulley itself. Some pulleys, like the one in the picture, show a solid, one piece steel pulley. There is also a common two...

Reproduction set of color coded A/C rubber hoses, two T connectors and vacuum diagram.

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used rectangular center duct tube for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory air conditioning. Wire reinforced foam, will show some snags or signs of use. Will not have gaping holes. Was originally stapled to the center housing. Ford part number C7ZZ-19B680-B.

A/C and heater control bezel or face plate. Grade A- used condition, standard pebble grain trim. Check back often, this type and grade of part is seldom in stock very long.Bezel only, no levers or switch.Ford part # C7ZA-19C705.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.

Regardless of which V-8 engine, C7ZA-19972-E is the correct part number. This hose is approximately 20 inches long. Two different crimped ends, smooth and waffle may be the difference between Dearborn and San Jose or 1967 and 1968. Anyone know?The Ford MPC number is C7AZ-19972-A.

New Old Stock A/C drain hose for Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. The best part is that because this is a NOS part, it will fit right the first time and be absolutely correct!Ford part #: C7ZZ-19858-C.

Two of these little plastic protectors came on Mercury Cougars and Ford Mustangs equipped with Air Conditioning. They are affixed to the front cross member using the same bolts that holds your condenser in place. Their purpose was to protect the wiring harness from potential damage if the car were to get into a collision. These are very hard to find today as most were discarded the first time the condenser was replaced. Even your most experienced judges usually have never seen or heard of this...

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

Passenger side air conditioning register vent with slight manufacturer blemishes. See photos for details.

Vacuum switch not included. This control switch lever assembly only, for the vacuum and damper door consists of the two lever assembly for the vacuum and cable actuation of the A/C plenums damper doors on Mercury Cougar and Ford Mustang with integral A/C.Ford part # C7ZZ-19B888-A.

A Complete A/C and heater control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Check back often, this type and grade of part is seldom in stock very long.Ford part # C7WA-19980-A.

OEM Ford stove type bolt for the securing the early style belt tensioner pulley. Used on Cougars and Mustangs produced before 1/3/1967. For use with C5AA-8A919-B Air conditioning belt tensioning pulley.

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Reproduction 15x8 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14x6" styled steel wheel with a chrome outer rim and an original argent finish between the spokes on the center for your Mercury Cougar. This is a great...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 14x7" styled steel wheel with a chrome outer rim and an original argent finish between the chrome spokes on the center. No, Mercury never offered them in a...

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. Reproduction 15x8" styled steel wheel with a chrome outer rim for your Mercury Cougar. This unit comes with 4.5" back-space, unless ordered otherwise. Center caps, trim...

New aluminum 17x8" Magnum 500 wheel with a 4 inch backspace for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes the center cap. Lug nuts sold separately, get them here.

SUPPLIER IS BACKORDERED ON THIS WHEEL UNTIL FURTHER NOTICE.New aluminum 15x7" Magnum 500 wheel with a 4 inch backspace for your Mercury Cougar or Ford Mustang.  Includes generic plastic center cap.

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand.These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

9-23-2019 Update! We are no longer carrying these as we are not happy with the amount of weight it takes to balance them. Unfortunately the founder of Specialty Wheels passed away several years ago and since then the company has changed hands a couple of times and the quality has suffered. No returns and no plans to reorder. No, Mercury never offered wheels in a 15x7" for an early Cougar... We now sell more of these custom made SS wheels than the original 14x6" version. Not only do they look...

Reproduction 14x6" Magnum 500 wheel for the Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant, but it holds up great year after year. You may save a few dollars buying the other brands out there, but why? We now have Magnum 500 caps that sport the Mercury Logo with multiple background colors and the walking cat caps as well. Center caps and lugs are sold separate. *NOTE* Please...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

Reproduction 15x6" Magnum 500 wheel for the Mercury Cougar or Ford Mustang. Here is an oddball you will probably not find advertised elsewhere... The total width of this wheel is 6 7/8" with a 4" backspace.Center caps and lugs are sold separate. *NOTE* Please allow 4 to 5 weeks for delivery.NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

The only reason you would buy an original used unit is that you would want to match your existing original caps. The reproductions we carry are actually much better quality than the originals, as they will never fall off. Chrome center cap with black background and chrome Mercury man logo. Came from the factory on 1967 and 1968 Mercury Cougars with Styled Steel Wheels, but will work on any 67-70 with Styled Steel Wheels.Fits the following models with style steel wheels:1967 Mercury Cougar1968...

Set of 4 Chrome center caps with red background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Reproduction chrome spinner center cap for the Mercury Cougar equipped with the magnum 500 wheel. Actually, this unit will work on any Ford, GM or Mopar Magnum wheel. Looks great and the mounting system is far superior to the originals. These look really aggressive.*NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which you can get right here. ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Reproduction chrome spinner cap for the Mercury or Ford that is equipped with Magnum 500 wheels. This cap will also work with any Ford, GM or Mopar Magnum 500 wheel. With a mounting system that is far superior to the original, this unit will definitely give your ride a more aggressive look. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which...

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.

C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B grade, due to pits in the chrome. This version is the one held down with 4 screws. Part number C7WB-7262-A is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C7ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B+ grade, due to pits in the chrome. This version is the one held down with 2 screws. Part number C7WB-7262-C is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...

C7ZZ-7515-D Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Cougar 1967 through 2-15-1968. 390-4V engines only, XR7, XR7-G. Mustang 1967 through 2-15-1968. 390-4V only, GT. Mustang 1967. K code 289 HiPo 4 speed only. GT

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with 4 speed transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-A or C7ZZ-17260-J. Has captured hold down bracket at transmission. Cable has a rubber hose at the transmission end. These measure out about 76 inches long. Also has a metal sleeve about 10 inches from the speedometer cluster end, Cable clamp? Used condition, will have road grime, and maybe a couple of abrasions or small...

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...