All Available Parts - 1967 Mercury Cougar

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check out our video on dash removal and restoration: ...

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has occurred on the panel is to remove the emblem for comparison purposes. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side.Check...

This used set of three XR7 woodgrain dash inserts for the Mercury Cougar without A/C are the best of the best of which we can provide you with. These grade "A" inserts retain a rich, original looking finish and have not been subjected to prolonged damaging UV rays. We carefully match these under bright lights to ensure they match color wise. There may be light surface scratches, no dings or other blemishes, and all four toggle switch labels will be in place. Includes a brand new, correct XR-7...

This set of three woodgrain dash inserts for the Mercury Cougar with A/C are not as good as our grade "A" unit. However, it will work well for your daily driver. These retain an original looking finish and we carefully match these under bright lights to ensure they match color wise. This dash insert may have some slight scratches, dings or other blemishes, and all four toggle switch labels will be in place. Click here for the non A/C version without the center hole.Check out this video ...

Used " Red " brake indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time.

Used " Red " belt indicator lens for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. The lens may have a slight arc to it due to the heat from the bulb over time.

Used " GREEN " turn signal indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used " RED " brake indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used " RED " belt indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad. The late 1967 through 1968 used a lens with a small metal housing.

Used " BLUE " high beam indicator lens for the Mercury Cougar. This is the early 1967 lens that was taped to the back of the dash pad.  The late 1967 through 1968 used a lens with a small metal housing. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

Used metal indicator lens bezel for the Mercury Cougar. This is for late 1967 through 1968 which uses the small housing. The early 1967 lens was taped to the back of the dash pad. Be aware that there are 2 sizes. This bezel is for the brake, belt and turn indicators. It also is for the high beam on the 1967 which used the small indicator. On the 1968 Cougars, they had the large high beam indicator.

These studs and nuts are used to repair the passenger side mounting studs. The studs need to be drilled out using a 1/4" drill bit. Once done, use a 2 part epoxy and install the stud. Make sure to avoid getting epoxy on the threads where the nut will be installed. Once dry, install the bezel into the dash and use a 3/8 # deep well socket to install the nut. CAUTION: Only tighten finger tight to avoid cracking or breaking the bezel.

Reproduction heater dash plate for the 67 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).Replaces Ford part number C7ZZ-18A651-B

This set of three woodgrain dash inserts for the Mercury Cougar without A/C are not as good as our grade "B" units. However, it will work for your lower quality daily driver. These retain an original looking finish and we carefully match these under bright lights to ensure they match color wise. This dash insert will have scratches, dings, or other blemishes, and all four toggle switch labels will be in place. Click here for the A/C version. (A/C version has the rectangular cutout in the...

Used high beam indicator lens for the 67 XR7 Cougar.

Used "left map" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used "right map" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used "courtesy" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used "panel" center dash XR-7 dash bezel plaque for the toggle switch identifiers. This item will require a touch up with a little polish and some re-painting of the lettering in most cases to make them look perfect. The stems are cut from the back so a little dab of good thick glue will hold them in place.

Used grade B driver side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check...

Used grade B passenger side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. Emblem will most likely need to be replaced. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has...

New for December 2024! After a long wait these dash bezel kits are finally in production and hopefully will be in hand by Christmas (or shortly thereafter). As the seasoned Cougar owner will quickly point out, there are several differences between the 1967 and 1968 xr7 dash bezels. We have chosen to take the best elements of both years and combine them into one set as tooling to do both would be cost prohibitive. Without getting into the weeds, these dashes more closely resemble the 1968...

New for December 2024! After a long wait these dash bezel kits are finally in production and hopefully will be in hand by Christmas (or shortly thereafter). As the seasoned Cougar owner will quickly point out, there are several differences between the 1967 and 1968 Standard dash bezels. We have chosen to take the best elements of both years and combine them into one set as tooling to do both would be cost prohibitive. This set-up will work for face pads that take either clips or screws. ...

Complete gauge cluster with toggle switches, lenses and gauges as shown here. This is a grade "B" set that will only need detailing and to have the plastic bezels restored to be show quality. Check out our video on dash removal and restoration: ...

These are ready to ship now! Sold in a set of four. Specific to 1967 XR-7.There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch with a large shaft, 1968 with smaller shaft and 1968 with a small shaft that has been milled down on two sides. The reason Ford decreased the size of shaft in 1968 was to enlarge the thickness of the plastic on the toggle tips. By decreasing the size of...

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Quality reproduction to replace your pitted original. Replaces Ford Part #: C7ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Inexpensive upgrade, replaces that bezel damaged by improper screw driver removal. We also sell the special tool that removes this without hassle or damage

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used ignition lock cylinder bezel for any 1967-68 Mercury Cougar, ford Mustang and likely Fairlane / Comet. Good used condition, we recycle the pitted crusty ones. Half the price of the repop version. We also sell the special tool that removes this without hassle or damage.Replaces Ford part number C6OZ-11584-A.

This is the longer of the two versions found on the 1967 XR7 and also found on the Shelby and Mustang. The lens used with this reset button has a smaller hole than the 1968 version.

Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.

Used wiper knob for any 1967 Mercury Cougar. This version is smaller than the 1968 knob. Unlike the 1968 version, there is no set screw, and is simply pressed into place. You may need to use a bit of adhesive to hold in place. Good condition, will have a small rust pit or two.

Headlight switch knob for any 1967 Mercury Cougar or Ford Mustang. Not the same as 1968. This is a nice detail item for concours judged cars. There is a difference between 1967 and 1968 knobs as shown in the photos. Nice used condition.  Original Ford part number C7ZZ-11661-A.

This two piece painted trim set helps to secure the dash pad in place at the bottom of the windshield. 1968 Mercury Cougar used a slightly shorter trim set due to the padded windshield pillar pads. The 1967 will work fine, all of holes line up the same. These 1967 trim pieces also have a smooth painted surface, 1968 Cougar pieces have a slightly textured painted finish. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. Will...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in BLUE for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK IVY GOLD or DARK GREEN for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK RED for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. Please Note: Color on these is inconsistent and never spot on...

Of the three covers used on the 67-73 Cougars we find this one the most difficult to use. Will Not Work On Badly Distorted Dash Pads. The problem is not with the product but rather the design of the original dash pad. Unlike the 69-73 pads the 67-68 pads are prone to warping (sagging) badly. Since this glue on shell is rather rigid you have to have a mostly straight pad to work with. Large cracks are no problem even if your pad is curling at the cracks, just break off the portions of your...

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

New improved set of 6 screw for the glove compartment hinge on all 1967-68 Mercury Cougar and Ford Mustangs. Three 10-24 bolts with 0.72" conical washer heads to go into dash, and three 10-24 bolts with 0.50" conical washer heads to attach to glove box door. This is an updated proper kit for 1967-68 Mercury Cougar and Ford Mustang glove box door hinge. All AMK bolts, but WCCC special recipe. 6 pieces as shown.

Used door / lid for the glove box in the 1967 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this door on 1967 and into 1968 Cougars. Sometime in early 1968 this glove box door came with three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford part # C7ZZ-6506024-A.*NOTE*...

Used door / lid for the glove box on any 1968 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this design of door with the 3 holes, well into the 1968 production run. 1967 and early 1968 doors are typically without the three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford...

Used glove box liner or plastic box for any 1968 Mercury Cougar or Ford Mustang these do have the flat smooth area for installing the tire pressure decal. This is nearly the same as the 1967 used and Scott Drake reproduction, which lack the smooth section for the tire pressure decal. Good used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange.Replaces Ford part number C8ZB-6506010-A.

Used hinge for any early 1967 Mercury Cougar or Ford Mustang. This early hinge is flat, the later 1967 and 1968 hinge had two ribs formed for added strength. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-A.

Used hinge for any 1967-68 Mercury Cougar or Ford Mustang. This hinge has two ribs formed for added strength. There was an early 1967 version of this hinge that did not have the ribbing. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-B.

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Used glove box catch for any 1967-68 Mercury Cougar or Ford Mustang. Several versions of this catch were used 1967-68, this is the most common version. Replaces Ford part number C6OZ-6206064-A.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. See related for reproduction and 1967 used.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1967, notice the push button with square edge? 1968 push buttons had rounded edges. See related for reproduction and 1968 used.

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Door panel clips for the 1967 Standard or XR7. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Fits either 1967 or 1968 Mercury Cougar or Ford Mustang. Technically this is a copy of the 1967 factory installed version. 1968 factory glove box liners have a smooth section for installing the tire pressure decal. See the related items for 1967 and 1968 good used liners. Replaces Ford part #: C7ZZ-6506010-A.

Used glove box liner or plastic box for any 1967 Mercury Cougar or Ford Mustang. This is the same as the Scott Drake reproduction, but it lacks the smooth section for the tire pressure decal which was introduced on the 1968 cars. Used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange, Replaces Ford part number C7ZB-6506010-A.

A great optional accessory. All new tooling was created to produce these glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Replace Ford Part #: C6DZ-6506072.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges.

Don't throw away those panels just because the backing boards are broken and warped! You cannot buy reproduction panels for the 67-70 Mercury Cougar, but you can get this pair of backer boards. If your vinyl is good, then you will want to put the work into them. These are not a quick fix, they do take time to install but the end result is worth it. These will work on your 67-68 XR7, Decor or Standard model as they are cut for all models and all options (i.e. manual remote mirror, courtesy...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Reproduction medium blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed.*NOTE* There are two types of this trim found in the 1967-68, the smooth or rough texture. ...

Good used metal portion of the door panel. If yours is bent or you're doing custom made door panels, you will need these.

Good used metal portion of the door panel. If yours is bent or you're doing custom made door panels, you will need these.

Check out our door panel inventory video below: *NOTE* Door panels sold bare, meaning without hardware, armrests, map pockets, window cranks, courtesy lights, door pulls, or door handles. ...

Used door courtesy light lens on the 67 - 70 Cougar. Because of the heat and placement of the bulb behind this lens, they were prone to burning or in some cases melting. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the reflector lens here. Right is same as left, sold individually. ...

Used door courtesy light reflector used on 67 - 70 Cougars. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the light lens here. Right is same as left, sold individually.

Fastener kit for installing the top of the map pockets on 1967-68 Mercury Cougar XR7 models. The flat nuts go behind the door panel and screws secure the elastic through the door panels. Kit includes 4 #8 flat nuts, and 4 #8 chrome screws. 

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Fits 1967 and 1968 Standard or XR7

Used dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy...

Good used light bar for the convenience control indicator lights on the 1967 Cougar dash face pad. Indicators lights are for belts, door, fuel and park.

One kit does both rear armrests for the XR7 or Standard interior coupe.

Passenger side rear arm rest for 1967-68 Mercury Cougar. Grade "B" rear interior armrest. Grade "B" armrests are pulling away from their backing but have no splits, cigarette burns or other obvious defects. They probably need to be painted with vinyl paint, especially since we can "almost" guarantee we will not have both sides of "your" color in stock. Please indicate which color you would prefer and we will do our best to accommodate you. The downfall of a "B" armrest is that it will show an...

Decent reproduction of the 1967 and 1968 XR7 Armrest Plugs. Only available in Black. Sold as a SET OF FOUR. Replaces Ford part # C7ZZ-6524056 or C8ZZ-6524056.

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not concours like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7 but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7.  Color on these is inconsistent and never spot on to the original.

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not concours like the XR7 but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

Reproduction front armrest in black for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

Reproduction front armrest in blue for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

Reproduction front armrest in dark ivy gold / dark green for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same...

Reproduction front armrest in parchment / off-white for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for...

Reproduction front armrest in red for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

Reproduction front armrest in saddle for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

This armrest is correct for the 1968 Shelby / Ford Mustang, but works well as a reasonably close substitute for the 1967 - 1968 Mercury Cougar XR7. The contour is the same as found on the 1968 XR7, the 1967 XR7 had more squared off edges. The texture is not course like the XR7, but rather smooth to match the grain of vinyl on the perimeter of the XR7 door panels, sides of seats and Cougar dash pad. It does not look out of place in my opinion and is what I would consider to be average to good...

Reproduction front armrest in turquoise for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...