All Available Parts - 1969 Ford Mustang

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

1969 302-4V Boss Eliminator Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9ZF-9510-J stamped on the carburetor air horn with a 903 date code. Holley list #4511, 780 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

C9ZE-9431-A Factory original cast iron exhaust manifold for driver side. Correct for all Boss 302 Eliminators 1969 and 1970.

C9ZE-9428-A Factory original cast iron exhaust manifold for passenger side. Correct for all Boss 302 Eliminators 1969 and 1970. Nice piece from a CA car, no damage or pitting.

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C8OE-9430-D and left C8OE-9431-B side matching exhaust manifolds.

C8OE-9431-B 428 Cobra Jet factory original cast iron exhaust manifold for driver side. For all 1969-1970 428CJ Cougars after 9/2/1968 build date.

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Closest reproduction fan clutch on the market that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.69 inches. Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino, Cyclone, Ranchero with 428CJ engines. Varies the fan speed with temperature of the air behind the radiator. Engaged (high...

These steel tubes made to exact O.E.M. standards and specifications.

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

351 Windsor factory cast iron exhaust manifold set, both a correct right C9OE-9430-B and left C9OE-9431-B side matching exhaust manifolds. Same manifolds used on all 351 Windsor engines in 1969 and 1970.  No extra charge to look for a date coded pair but no promise we can hit it spot on either.  

Elbow with water restrictor.

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Rebuilt water pump, Ford casting C9AE-8505-A, dated 9A9 January 9, 1969. Fits any 390 or 428 Cobra Jet.

Used 'CORE" grade radiator, marked C9ZE-D or D1, .. etc. 20 inch used radiator from 1969 Mercury Cougar with Boss 302 or 351W or 1969 Ford Mustang with 302 or 351W or engines. This radiator will have the lower tank for transmission lines. Core grade, likely it has been recored at some point in the last 45 plus years. Limited to stock on hand.Restoring or re-coring OEM radiators is expensive and more for the concours crowd. New or reproduction radiators makes much more economical sense.Ford...

C9WE-8600-A 5 blade clutch fan for Boss 302 Mercury Cougar Eliminator and Ford Mustang Boss2 cars built before 4-14-1969. 17-1/2 inches in diameter and has the 2-3/8 inch hole for the separate clutch. On page 11-05-01 of the 1969 Ford Shop Manual, volume II it does list this as a 351w Cougar fan. Would like to know if anyone has actually found one of these on a 1969 Cougar with AC. Please contact us if you have any light you can shed on this very rare fan. Click on images to enlarge. Check out...

C9OE-H Application is for all 1969 428SCJ engines with the W code 4.30:1 axle ratio, and some instances it was found on 1970 428 super cobra jet engines. Fan description - 6 blade fixed pitch and 18 inches in diameter. Ford master part number C9OZ-8600-D. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9ZZ-8600-C. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler...

Used FoMoCo radiator marked C8ZE-L1 and dated 8KB, which we believe is 2nd week of October 1968. This is for an early built 1969 Mercury Cougar or Ford Mustang with 390-4V or 428CJ and 4 speed transmissions. Good used radiator for recoring and restoration.Replaces Ford part number C8ZE-8005-L or C8ZZ-8005-C.

Used original fan shroud for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. Shround will have minor damage as shown. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. Ford part # C9OZ-8146-A For some helpful tips on upgrading your Cougar (or Mustang) cooling...

Found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1969 - 1970 all engines. One per car, one on the drivers side of the radiator. *Note - This is a shorter side shield than is found on the 1967 and 1968 Cougar.*Note - Block off plate not needed with the 24 inch radiators.

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

C6OE-D and C7AE-F marked fans. Applications: 1. 1968 C code 289-2V engine without air conditioning or heavy duty, or 'extra cooling' option (small radiator). 2. 1969 Boss 302 Eliminator and Mustang. Mustang owners, this 4 blade fan with the part number C6OE-D and (C7AE-F for 1967 and later), is also correct for those K code 289 HiPo engines in both 1966 and 1967. Fan description - 4 blades and 17-1/8 inches in diameter. Ford master part number C6OZ-8600-D. Check out this interesting video...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Tested and inspected neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...

NOS big block motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Ford Part #: D1ZZ-6038-A.

Keep in mind that if you have the original motor mounts in your 1967 with a 289 or 1969-1970 convertible these mounts will not work. Nobody sells motor mounts for them, period. This is contrary to what every auto parts store will tell you. Your options are to purchase our (used 68-70 frame stands) or modify your existing ones.Sold individually, two required per car, left is the same as right.

Used alternator bracket for any 1968-69 Mercury Cougar or Ford Mustang with 289 / 302 / 351W engine, but without factory smog pump.Replaces Ford part number C8OE-10156-A.*Trivia - the only difference between this bracket, and the C6OE-10156-A bracket is the thickness of the steel. Either one will work on 289/302/351W engines 1966-69.

Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with...

Used standard grade A main under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with XR7...

Reproduction under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with XR7 model Cougar or Mustang with Ammeter. Replaces Ford part # C9ZZ-14290-R. Fits: 1969 Mercury Cougar Standard 1969 Ford Mustang ...

D0ZB-13A769-B Left side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-B. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note* Does not include door ajar or factory stereo wiring plugs. ...

New Old Stock If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. Replaces Ford Part #: C9ZZ-7A247-B, SW 877 

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Door jamb switch for the 1969 Cougar or Mustang with a tilt column.

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

Correct cast aluminum elbow fitting for the rear of the C8AZ-9A486-C smog pump. This elbow will have two single mounting holes. The service replacement elbow (Ford part number D4TZ-9C475-A) has two sets of double mounting holes. Correct Ford part number C8AZ-9C475-A.

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings. New copy of the 1968-69 Mercury Cougar and Ford Mustang manual drum brake master cylinder lines. 

Factory used and tested under dash wiring harness for all 1968 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the kick panel speakers in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1969-70 cars. White speaker wire goes to the passenger side speaker, and the orange colored wire...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your radio. Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door...

Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. T9MZ. *NOTE* Does not come with bracket or knobs. Ford part # C9ZA-19A242. *TRIVIA* The window sticker price for this option in 1969 was $195.60. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help...

Mercury Cougar and Ford Mustang, Bendix manufactured, factory installed AM/FM stereo radio. Tested and found to work well. Knobs sold separately. Ford part # C9ZA-19A241 or 9FBZ-A. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Mercury Cougar and Ford Mustang AM-8 track Motorola manufactured radio. May or may not work and wiring plugs may be cut. Great radio for reconditioning and often times the 8 track feature only needs a drive belt to work perfectly again. Ford part # C9ZA-19A242. *TRIVIA* The window sticker price for this option in 1969 was $195.60. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical...

We do not have any at this time . . . Very rare part in great condition. This was pulled from a very original 1970 H code XR7 with power windows, tilt column and AC. Technically not correct for 69 in that the shade of green would be darker in 1969. Why this car did not have the xr7 woodgrain delete plate we are unsure.

Take a look at the smaller image to see the repro and used side by side. The repro is slightly taller and has extra holes in it so it fits other applications. Why deviate from 100% correct if you don't need to. Ford Part # C9ZZ-18842-A.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

Carter manufactured valve with C8TE-9B289-B and 4490-S imprinted on the valves' cover. Another hard to find part with correct date codes specific to Boss 302. Ford part number C8TZ-9B289-A. These units are used, not tested and one should assume they are non-functional. These units are used, not tested and one should assume they are non-functional. *Note, we try to carry later manufactured 'Service replacement' Carter anti backfire valves which are in every way the same, but...

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator adjusting bracket. It has the Ford stamped casting number of C8AE-10145-B. Ford part number is C8AZ-10145-B.

Bolt for mounting thermactor smog pump to engine. Must be used in conjunction with thermactor alternator bracket and pump spacer. Bolt dimensions 3/8"-16 x 5.75" long.

C9OE-9C480-A 1969 and 1970 428 Cobra Jet (R and Q code engines) smog pump pulley with air conditioning, manual and automatic transmissions. 3 bolt smog pump pulley with a diameter of 5.10" inches. Ford part number C9OZ-9B447-A.

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

New old Stock rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang. NOS Ford, no Autolite or Motorcraft box. Ford Part Number C8OZ-9D612-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Reproduction rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang.  Replaces Ford Part Number C8OZ-9D612-C

This vacuum actuated door assembly was used on several performance motors without Ram Air. When extra air was needed under heavy acceleration the vacuum actuator opened the door on the side of the air cleaner base. The actuator on this unit needs to be rebuilt so this is considered a good core only.

This is a 1969 lid. The 1968 lid had several differences, most notable was the stamping wrinkles. This is  Flapper mid plate for use on non-shaker cars. 1969-70 Mercury Cougar with R or Q code engine with ram air. 1969 Mercury mid sized cars such as Montego, and Cyclone all with R code 428CJ or SCJ engines. Ford part number C9ZA-9600-C. This version is said to have been used starting in May of 1968, so there would have been some cars equipped with this mid plate.There are many...

C9ZE-9600-E Air cleaner base for the 1968 and early 1969 R code 428 Cobra Jet engine option. Additionally one way to identify this air cleaner is the dimple that clears the rear float screw found on the factory Holley carburetor. Early 1969 production is through 2/17/1969, after that date there was a vent added for automatic choke issues. About 16-3/8" inches in diameter. Ford part number C9ZZ-9600-E or C8ZZ-9600-A. Click on images to enlarge. ...

C9ZF-9600-F Late production 1969 428 Cobra Jet ram air engine air cleaner base. For those cars built after 2/17/1969. Identified with the addition of a small vent fitting and strap for vent hose on bottom. About 16-3/8" inches in diameter. Ford part number C9ZZ-9600-F. Click on images to enlarge. ...

This air cleaner base (Ford part number C8OZ-9600-C) was used on all 1969 BOSS 302, 1969 S code 390 IP (Improved Performance) Cougars and 1969 Cougars equipped with a Q code 428 CJ. The air cleaner shown here was taken from a 1969 390 S code with a 21C date (March 21st). The Cobra Jet Cougars saw a minor change in these air cleaners on February 17th (or close) 1969. The change included the addition of a small metal strap that was spot welded to the lower portion of the passenger side of the...

C9OF-9600-H Late production 1969 Q code 428 Cobra Jet non-ram air engine air cleaner base. For those cars built after 2/17/1969. Identified with the addition of a small vent fitting and strap for vent hose on bottom. Unique 1969 air cleaner base with a rectangular vacuum actuated valve on the drivers side. About 16-3/8" inches in diameter. Ford part number C9OZ-9600-H.

C8OF-9600-C Unique 1969 air cleaner base with a rectangular vacuum actuated valve on the drivers side. Applications include 1969 Q code 428CJ (non ram-air), 1969 S code 390-4V, and 1969 Boss 302 Eliminator. About 16-3/8" inches in diameter. Early 1969 production through 2/17/1969, after that date there was a vent added for automatic choke issues. Ford part number C8OZ-9600-C.

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

For all 1969 Mercury Cougar trunks. The MPC lists the correct length as 8-3/4 inches in total length, with 4 inches of the end being threaded but we have found without fail them to be about 10 3/4" with about 3" of threads. I say "about because some have a blunt end while other versions have a tappered end which will add about 1/8" to the length. Those threads are 1/2-13.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Reproduction of the protector felt pad between the spare tire and jack handle for the 68 through 70 Mercury Cougar with styled steel wheels. Used only in conjunction with applications that store the jack components on top of the wheel.

1969 Ford four speed shifter rebuild kit. Kit includes tension spring, steel clip, threaded machined shaft, pair of roll pins, pair of dowel pins, and two bolts. Information indicates that all 1969 4 speed shifters are the same across all car lines and for all engines. Link to the Ford shifter linkage expert. Check out our video on rebuilding your shifter below: ...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Not rusty or water damaged, hardware sold separately. Vinyl is often UV damaged. Please indicate what color you prefer and we'll try to accommodate, but there's no guarantee we'll have it.

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

Used servo cover from a 1969-71 Ford C-6 transmission. This cover has the big R cast into it, which designates it as an "R" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, from 1968-70 Mercury Cougar and Ford Mustangs with Q or R code 428CJ engines. Additionally 1971 Mercury Cougar or Ford Mustang with J or C code 429CJ engines. 1968-71 Ford and Mercury mid sized cars also with 428CJ or 429CJ. Cover only, marked C8OP-7D027-A.

Used servo cover from a 1968-69 Ford C-6 transmission. This cover has the big D cast into it, which designates it as an "D" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, for 1968 Mercury Cougar and Ford Mustangs with X code 390-2V engines. Additionally, 1969 Mercury Cougar and Ford Mustang with the S code 390-4V or 390IP engine. Cover only, marked C6AP-7D027-A.

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this power steering, idler arm would have had a yellow paint mark on...

Fits 1969 - 1970 BOSS 429 and 428 Cobra Jet - C80A-3D746-A. Blissfield Manufacturing Company was the original equipment manufacturer (OEM) for these Power Steering Coolers to Ford Motor Company. Located on the driver side strut rod support. Ford Part # C8OA-3D746-A

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Rear seat bottom or lower cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number C9WB-7663120.*Note - Does not fit coupe or fastback.Lower frame measures 46" at it's widest point and 18.5" high This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat back or upper cushion from any 1969-70 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C9WB-7666700. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. Though these seem to fit in a 64-70 Mustang convertible, the correct engineering number that would...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...