All Available Parts - 1969 Mercury Cougar

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.

Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock

Used pair of red diffusers for the temperature or fuel gauge on the 69 - 70 Mercury Cougar. The wording (alternator, park, brake, oil etc.) is on the actual lens and not the diffuser, so these can be used on either gauge.Sold as a pair.

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Fits the 1969 Standard Cougar, good used housing with no rust or modifications.Ford part number C9WF-10843

Fits the 1969 Cougar XR7, good used housing with no rust or modifications.Ford part number C9WF-10843

Used red plug wiring pigtail for the 69 Cougar sequential unit. 

Reproduction wiring pigtail repair kit for the sequential box on the 1969 - 1973 Cougar.  Included are: 1 five pin red connector1 five pin black connector

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction 15 x 7 gold haze colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

The Rocket "Strike" provides timeless and classic traditional styling at very affordable prices. The Rocket Strike is a 1-piece wheel precision crafted from A356 aluminum and topped off with a vintage style aluminum o-ring center cap. It has a lug centric design and uses standard 60-degree conical seat lug nuts (sold separately). There is 3.00 inches of hub clearance under the center cap. Load rating is 1560 lbs per wheel.4.25 Back spacingFully polished center and outer rim.  Cast...

Reproduction set of 20 lug nuts used specifically on the Rocket Racing wheels. These lugs will not work on any other wheel.

CURRENT ETA FOR THESE WHEELS IS 2/24/2023 Reproduction 17 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a gold background.  *NOTE - These caps are specifically designed to fit the LW10 series wheels.

Reproduction Cobra GT 350 center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic blue cobra with red detail.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

New midland control hub assembly and disassembly tool for use with the 67 - 69 Cougar and Mustang Midland style booster

These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.

Used retaining bolt with nut for the fixed column on any 69 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

Reproduction pair of front apron assemblies without shock towers, perfect for someone doing a resto-mod or IFS conversion. Sold as a pair.

Used original Golde sunroof gear box. This box is found above the headliner on the passenger side.Golde part number 0142850 00

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

The car pictured is a 67, but the copyright says "1969 Fred Bonner Corporation" and the header says Mercury Cougar introduced 1968.Measures 5"x7"

Accessory pamphlet "For Active People". 31 pages Volume 69 MSD-1A. This brochure highlights everything from the floor mats to an 8-track.

NOS Rand McNally Lincoln Mercury atlas and travel guide, originally distributed to customers through their local dealer. Includes state, city and "special maps" that include the US, Central America, Mexico and Puerto Rico. Also includes a special features section with points of interest.

NOS 1969 Mercury Competition Team pamphlet. These packets were handed out to Mercury team dragsters in order to log their run times. Once you logged enough class wins, the concept was to mail the pamphlet to the Mercury Competition Team Headquarters and claim your Mercury Competition Team Driver's Award Certificate. Originally these booklets included stickers and decals, but those seem to be missing from this particular booklet. Also included is an order form from that year to...

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

NOS C6 Automatic Transmission training handbook from the Ford Marketing Corporation. Course 7521, Vol. 71 S4-L2. Everything from the torque converter, to the planetary gear and hydraulic systems to diagnosis and adjustments are detailed in this manual. Everything about descriptions, testing procedures and specifications were approved by Ford. Filled with color photos and diagrams. There is an unknown name written on the inside of the cover, however all pages are intact and in perfect...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Dark Red / Maroon floor mats for the 67 - 73 Cougar embroidered with the XR7 logo.

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Green floor mats for the 67 - 73 Cougar embroidered with the Cougar script logo.

Dark green floor mats for the 67 - 73 Cougar embroidered with the walking cat logo.

NOS 41" x 24" Walking Cat nylon banner / flag. These were hung up around dealers back in the sixties and early seventies. We're calling it a banner, but the 2 holes on one side of it indicates it may also be a flag.   NOTE* The reflectiveness of the nylon made it a bit difficult to photograph, just know that the banner is in fact white! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually...

Custom made Walking Cat belt buckle for the Cougar die hard. This would make a great gift for anyone who lives and breathes everything Cougar. The buckle is bare, unpainted and ready for you to customize how you see fit. We're not sure how we ended up with this awesome collectable, but it's definitely one of a kind and the only one we know of, so when it's gone it's gone!  Measures 3 3/8" x 2 1/4"

Never opened 1/25 scale 1969 Cougar XR7 Street Machines model kit #6533-10E0 from the AMT ERTL company in Dyersville IA. Includes detailed BOSS 429 engine with performance modifications, moveable steering wheel, vinyl tires and clear and plated parts. Decals include hood stripes with claws and a Cougar sunset mural type quarter panel image.

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

This dual male bracket is designed to hold your lap belt buckles when not in use. The Engineering number as seen on the bottom side reads C9ZB-65045A36AW.

Final issue / November 1975This manual was taken from the original box and each page was painstakingly placed in a Mylar sleeve. No damaged, missing pages or writing on pages. Anyone serious about buying and selling parts for a 1965 1966 1967 1968 1969 1970 1971 1972 Comet / Cyclone / Cougar / Mark III will find this all inclusive manual will quickly pay for itself. If you pick it up in person we can reduce the price significantly, we can store it for as long as you need until you can pack it...

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

NOS Ford service training manual on diagnosis of charging system problems. This booklet is a guide to diagnosis of the alternator, regulator, battery and wiring issues. It contains diagnostic procedures and self instructional tests and was meant to be used as a reference guide for the "charging system videotape (video tape not included).  16 pages long with tests and answers.Issued Dec. 1974, # 365-240

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.

This big book measures 18" x 13" x 3" and weighs 8 pounds. It's a must have if you are serious about electrical or vacuum work on the Cougar, Thunderbird, Mark III, Montego, Fairlane, Maverick, Cyclone, Bronco, F100, Torino, Mustang or other Ford products products from 1969. Condition is used and will have a few pages that have torn away from the rings. Form 7795P-69 Course 13003 and 1703

Extremely rare open box 1969 Mercury Cougar funny car model kit, AMT # T342 200. Kenz & Leslie Wynn's 777 High Country II funny car with full color cardboard drag display diorama. Unbuilt model kit, complete with contents unopened and still factory sealed inside box (decals are slightly blemished). 1/25th scale, molded in white. Model kit reference guide list the model kit as the one and only 42 year old 1969 issue, never reissued, long out of production. Part of the All...

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad...

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

Used custom cut driver side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551701-A

Used custom cut passenger side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551700-A

New open box 2000 AMT / ERTL "The Replica" magazine promotional 1969 Mercury Cougar Eliminator model kit. This kit was available to subscribers of The Replica Magazine. Limited to 3500 kits, this was a much sought after collectible. This particular model is in perfect condition, although the actual model kit box is unsealed, all parts are still in their original plastic wrapping and untouched. Comes inside the original brown box. 

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used indicator lenses for the 1969 Standard fuel gauge. Taken from a used gauge, they will be in the best shape possible, no serious wear, no breaks and no cracks. Lettering will be legible and intact. Diffusers are also available.

New open box "Dyno" Don Nicholson's Super Cat 1969 Mercury Cougar model kit. 5 ways to build, Super Cat Drag Car, Street Rod, Eliminator, Stock XR7 or Custom. This particular model is in perfect condition, although the actual model kit box is unsealed, all parts are still in their original plastic wrapping and untouched, even the decals are in great condition. Includes 428 Cobra Jet Engine, 429 Semi-Hemi Engine, Customer front end, side mirrors, side exhausts, bucket seats with head...

This Cougar II 1/25 scale factory sealed model kit was made by the Industro Motive Corp in Troy Michigan. This car was actually introduced in 1964 and was a Shelby Cobra based Ford- Cougar prototype vehicle that never made it into production.    Features: Retractable lightsWorking steeringOpening doorsOperating windowsPressure vent flapTubular frameChrome wire wheels260 cubic inch high performance engine ...

This listing is for a pair of walking cat die cast chrome cufflinks. These would be great for the serious collector who may want to add a bit of Cougar flair to outfit when hitting the town, or simply just another bit of memorabilia to add to their collection.  Walking Cat measures 1-3/16" across.

Ready to move into the Cougar big time? Well now's your chance with this flashy gold plated money clip emblazoned with the XR7-G shifter emblem. A great item to add to your collection of memorabilia, or to actually use! We're not sure of it's exact origin, but we though we'd pass on the opportunity for someone to get their hands on it. Circular center measures 1-1/2" across.

Ready to move into the Cougar big time? Well now's your chance with this flashy stainless steel money clip emblazoned with a gold XR7-G shifter style emblem. A great item to add to your collection of memorabilia, or to actually use! We're not sure of it's exact origin, but we though we'd pass on the opportunity for someone to get their hands on it. Old dirty carry bag included. Measures 2" x 1" Emblem measures 1-1/4" x 1/2"

There are 3 of these acorn nuts used per emblem. They are taller than what was used in 1968.Sold individually.

Patch panel for the driver side outer kick panel area of the exterior of the car, hidden by the fender. This panel has the correct drain cutout for water coming down from the cowl.

Patch panel for the passenger side outer kick panel area of the exterior of the car, hidden by the fender. This panel has the correct drain cutout for water coming down from the cowl.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...

This plate is what is located on the backside of your door jam where your striker threads in one. Two threaded holes for attaching the striker plates on any 1967-70 Mercury Cougar or Ford Mustang. Right and left are the same. 

This listing is for a Walking Cat keychain multi tool. We haven't been able to find much information on this, but it's definitely a cool item to add to your collection. Features a chrome plated swing out tool with a few flathead tips and nub-style phillips tips. 

This good used plastic trim part has been inspected for cracks and scrapes and has been found to be in good used condition. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted. This is the driver side, outer vertical piece for all 1969 Mercury Cougar and Ford Mustangs. 1970 has a different part number, but looks the same. We also sell the 1970 piece with D0Z.. casting number.

This is for your three or four speed manual transmission 1969 Cougar. The 69 is unique over the 70 in that it has provision for your seat belt buckles to be stored when not in use. This requires an additional woodgrain insert, we also have one listed that does not require the additional insert (no holes). Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts. *Note - This console part does have pre-drilled holes for installing the...

This console bezel is for your three or four speed manual transmission 1969 Cougar. The 69 is unique over the 70 in that it has a provision for your seat belt buckles. This does not require an additional woodgrain insert, so it is not technically correct for your Cougar. We list this unit because there is no quality XR7 burl grained inserts available at this time and some customers prefer the clean uncluttered look of the plain camera case finish. Absolute perfection in every detail, if all...

Correct color and texture, includes chromed plastic bezel. We also sell the decal only. This was used on the Eliminator / Decor or Standard Interiors but can also be used on your XR7. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

This is a bare bones console with no lid or insert. It is actually a 1969 console base but can be converted to 1970 by changing out the storage compartment area with a used 1970 storage compartment with no lighter. 1970 owners may want to keep the lighter as it makes for a nice power port that is easier to access than the one on the dash. This is a good value for the person who already has a console but the base has been damaged. Made from ABS plastic that is paintable with any solvent based...

Very correct reproduction, injection molded like original with correct Burled woodgrain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, your choice of flat or humped lid, insert designed for cars with automatic transmission, dark walnut bezel (xr7 burl grain is NOW available!) front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, triple-humped lid, insert designed for cars with manual transmission, simulated burl walnut bezel (correct for XR7), front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Very correct reproduction, injection molded like original with correct grain surface. Assembly includes; Base with metal support brackets, upper console panel (where shifter plate mounts) with metal retainers, front ashtray receptacle & holder with die cast lid and rubber lid bumpers, rear ashtray assembly, 1969 style compartment box with cigar lighter, hinge for compartment lid, cigar lighter with correct knob and chrome mounting plate. While not technically correct for the Cougar, many...

Reproduction upper portion to the center console found in the Mercury Cougar or Ford Mustang. This unit is a perfect fit in your Cougar or Mustang and features exact color and texture. It also comes with the front hooks to attach it to the lower base. The center console is a focal point of any cars interior and getting rid of that cracked, broken down old console will make a huge difference! *NOTE* This unit does not come with the ash tray assembly, but they're available used or reproduction. ...

This is a new reproduction available only in black. Perfect in fit and finish with the only difference from original being it does not have the sprayed on velvet-finish on the inside of the storage box. The correct lighter bezel and receptacle are included.

This is very close to being an exact reproduction. Only two things differ, the upper lip on the bezel is different in that the originals had a smaller lip on the top and this reproduction is the same on all four sides. The second difference is that the contour of the upper edge of the tray itself is not as crisp as the original and the catch has no roller but what an improvement over your rusted filthy unit! Nobody is ever going to notice but since I can see a difference when I put side by...

Knob is exact replacement, element is a generic replacement. Socket and element are manufactured by the same company to insure fit. Exact replacement for 1967-68 dash or 1969-70 under dash lighter and lighter socket. Replaces Ford part # C7ZZ-15052 and C6ZZ-15055-B.*Note - Retainer should have a ground lug on it in order to work with 1969 console cigar or cigarette lighters.

Knob is exact replacement, element is a generic replacement. Exact replacement for 67-68 dash or 69 center console lighter and lighter socket.

This replaces that rusty, scratched bezel in your 1969 Cougar or Mustang center console. Included is the support bracket for the backside.

Great for that missing or rusted ashtray in the front of your console. Nice snug fit and correct hole for light. Replaces Ford Part #: C9ZZ-6504788.

This is for your automatic transmission 1969 Cougar XR7, Standard, Decor or Eliminator console. The 1969 is unique over the 70 in that it has a provision for your seat belt buckles. This requires an additional woodgrain insert, we also have one listed that does not require the additional insert (no holes). Absolute perfection in every detail, if all reproductions were this nice there would be almost no market for used parts. *Note - This console part does have pre-drilled holes for installing...

This is for your automatic transmission 1969 Cougar. The 69 is unique over the 70 in that it has a provision for your seat belt buckles. This does not require an additional woodgrain insert. Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts.

Nice quality decal. This is for all Cougar consoles except XR7 which uses a dark burl pattern.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts!