All Available Parts - 1973 Mercury Cougar

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This ashtray lid was located on the rear interior quarter panels and was used on all 1971-73 Mercury Cougars and Mustangs. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish, is stamped steel and a slightly shorter lower base section. The removable ash receptacle is sold separately. Priced as good quality grade A units, no pitting.Ford part # D1ZZ-6530714-A.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. Check out this video

Good used part with no peeling foil covering or cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. We also have these in grade "B" for $43.85. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate. ...

Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A

D1WY-6522666 good used handle for 1971-73 Mercury Cougars with decor or XR7 interior trim. These will have the threaded inserts installed, we have various colors and some will have been previously painted as shown with the black handle in the picture. These are very limited to stock on hand. Rarely do we have more than a couple of these in stock but we will make an effort to get your desired color. If you MUST have a certain color email before ordering to check stock on hand. Keep in mind if...

Interior door panel grab handle or door pull. These are B grade handles. These will have damaged threaded inserts and will not be suitable for use to close your doors. These can be modified by drilling through the handle and installing a small acorn nut. Those are heavy doors, and these handles just weren't up to the task of hanging in there for 30 plus years. *NOTE* Please include in the 'comments' section your desired color, we will try to accommodate your requests.

Replaces Ford part #D1ZZ-13915-A. Comes in black only, used in conjunction with 73 Deluxe Horn Blow Switch Trim Plate

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

1970-74 Mercury Cougar rimblow horn pad bezel with hand painted woodgrain. These have been painstakingly hand painted by a local artist. 1970-74 standard and 1970-74 XR7 straight style wood grain. Does not include the 'kitty', 'kitty' sold separately. Cores cannot be bent or rusted heavily. Does not include the 'kitty', Cougar Emblem sold separately. Cores cannot be bent or rusted heavily. Core charge is refundable when restorable 1970-74 woodgrain insert is received by WCCC. Check out this...

Good used part with a little peeling on the foil and this part will most likely have cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

Optional trunk lamp. Includes mercury switch that mounts on inside trunk lip and wiring pigtail. Driver quality part, Bulbs available. Guaranteed to work, no cuts or splices. Can be added to most cars. Single wire female connector, located near the drivers side trunk hinge. Self grounds to deck lid, one power lead wire. Mercury switch turns on and off with the raising and lowering of the deck lid.

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages. Check out this video below where we used Kevin Marti's books extensively to decode a 1969 428 CJ Cougar

Have you been in a discussion with someone about how many W-code GTEs were made? The real percentage of Cardinal Red convertibles that were made? How many Eliminators were made each year? Now you'll know these things and so much more. This book contain never before published information drawn direct from company records, and over 14,000 statistics. This book includes: Exhaustive charts of paint color-trim combinations Engine-transmission production for each body style Option production rates...

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

Manual on how to modify your FE big block Ford for street or strip.

Complete reprint of 11 Supplemental Off Highway Performance Operation Parts Newsletters from Ford which were printed between January 1972 and Spring of 1973. Full of tips on modifying your vehicle for Drag, Strip and Oval Racing.

Saves time and frustration! Shows schematic and diagrams that reveal the location and function of the many vacuum systems on Cougar's.

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

Perfect fit.

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Includes both the left hand and right hand strut rod arm. These are required to install the reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C & C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but similar) from one end...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part # C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nuts and bolts, associated with the installation of our used 1970-73 strut rods.

AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.

This used tube with two flared fittings was originally used to connect the flexible pressure hose to the power steering pump on all 1971-73 Mercury Cougar and Ford Mustang with V8 engines. Ford shows this item in the chassis assembly manuals and it is called a "Pressure Line Outlet Tube Assembly" and the Ford part number is D1ZA-3E576-AC.

This used retaining clip was originally used to connect the two power steering hoses together at the power steering box. Used on all 1971-73 Mercury Cougar and Ford Mustang with power steering and V8 engines. Ford shows this item in the chassis assembly manuals and it is called a hose retaining clip, and the Ford part number is D1ZA-3E506-AC.

D1ZZ-3A697-A Application is for 1971-73 Cougar and Mustang with all V-8 engines including 351 and 429CJ. Originally found on pumps with tags numbered HBA-CG or HBA-CN. *Note - Until we can make a determination, this excludes pump #HBA-CF. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to look like grade A

Grade B Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps....

Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...

D1ZZ-3A697-A Application is for 1971-73 Cougar and Mustang with all V-8 engines including 351 and 429CJ. Originally found on pumps with tags numbered HBA-CG or HBA-CN. *Note - Until we can make a determination, this excludes pump #HBA-CF. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to look like grade A

HGA-CN Power Steering Pump Identification Tag - Used Tag marked HBA-CN beginning 7-1-1972 and 1973 Cougar and Mustang. Power steering pumps originally installed on 302, 351, 429CJ V-8 engines only. Various dates. *Note - Late 1972 and 1973 only.

This rod was used on all Cougars 1971 - 1973 equipped with a 351 and FMX transmission both 4V and 2V. Approximately 27" Black color code.

Used on both 351 2V and 4V motors equipped with the C6 transmission. Approximately 26-1/2" with red color code. The comparison picture with two rods side by side are the 71 - 73 FMX and C6 rods. *NOTE* Many assume the C6 was only available with a 351 equipped with a 4V but in fact you could get a C6 with a 351 2V in 1971 - 1973.

Automatic transmission kickdown control retracting spring. 1971-73 Mercury Cougar and full sized Ford/Mercury, mid sized Ford/Mercury, Ford Mustang, Maverick/Comet, and Thunderbird/Lincolns. V8 engines only. Replaces Ford Part #: D1AZ-7B146-A

Manual control shift linkage assembly for a floor shift FMX transmission in any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown. *Note - this will not work with a C6 transmission.

For all 1971 to 1973 Cougars and Mustangs with H code 351-2V and FMX automatic transmissions.  Ford part number D1ZZ-6A023-B.*NOTE* Two notes - There is a difference between 1969-70 and 1971-73 FMX cross members. Additionally, Ford did produce H code 351-2V engines with C-6 transmissions. Triple check.

Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.

1971 - 1973 Small block engine (351 cubic inch) and C-6 automatic transmission inspection cover. Transmission code 'U' found on select 1971-73 Cougars and 1971-73 Mustangs. Inspection plate for the flex plate and torque converters.Ford part number D1OZ-7986-A.

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.

Bolts for securing the inspection cover for small block C-6 automatic transmissions 1971-73 Mercury Cougar or Ford Mustang. Not sure why 3 bolts, but one is different.

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The early versions used the C5ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter dial black background. This part screws to the shifter bucket, and sits under the pointer when everything is assembled in your shifter bucket assembly. Fits all 1969-73 Mercury Cougar and Ford Mustangs with automatic transmissions. Original Ford part number C9ZZ-7A213-A also can be D1ZZ-7A213-A. Check out our video on rebuilding your shifter below: ...

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...

Automatic shifter arm pawl - late version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1970-73 Mercury Cougar and Ford Mustang. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need. Ford part number D0ZZ-7C442-A.We also list the early version. Check out our video on rebuilding your...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

3C511-351-73 Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1973 Cougar or Mustang with any 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. Most 351-2V engines received the FMX automatic transmission. Rod originally had a "Yellow" paint daub for identification purposes on the Dearborn assembly line. Shift rod approximately 18-1/2 inches long. Rod stamped D1ZA-7340-AA. Check out our video on rebuilding your shifter below: ...

This fragile little plastic arrow is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Bare automatic shifter bucket or housing. Fits all 71 -73 Mercury Cougar and Ford Mustangs with or without console. Also fits 1971+ Maverick and Comet with automatic floor shifters. If one runs with really worn shifter bushings for too long the hole in the side that the shifter arm passes through may be worn beyond tolerances. Ford part number D1ZZ-7A306-A. We inspect the shift detentes and the hole where the bushings go for wear. This bucket is different than the 1969-70 version as shown on...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction of the little plastic shift indicator arrow, that is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Unlike previous reproductions this has the correct grommet that passes through the firewall.  Replaces Ford Part #: C9ZZ-17260-A.  This cable measures 58 1/2" at its very most outer ends.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Speedometer cable that fits all 1969-73 Mercury Cougar and Ford Mustang with C-6 transmissions. This replacement cable is longer than the originals and does not have the firewall grommet. This cable measures 80" inches in length. Does not include speedometer gear, has correct style plastic clip that attaches to the back of the speedometer. Replaces Ford part # C9ZZ-17260-B, D0ZZ-17260-D, and D1ZZ-17260-G.

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

This screw attaches the speedometer / odometer to the instrument cluster housing. Two needed per speedometer, fits all years of Cougar 1967-73. This is an 8-32 x 3/8" hex flange head machine screw with captured washer. Sold individually. 

Reproduction transmission cooling lines made from OE steel for the Mercury Cougar or Ford Mustang equipped with the FMX automatic transmission and 351 engine.

Reproduction transmission cooling lines made of stainless steel for the Mercury Cougar equipped with the FMX automatic transmission and 351 engine. These lines are sold in pairs.

Reproduction transmission cooling lines made of Stainless Steel for the Mercury Cougar equipped with the C-6 automatic transmission and 351 engine. These lines are sold in pairs.

OE Steel Modulator Vacuum Line for all V8 engines with a C6 transmission except 429CJ or the 351C with a 4 barrel carburetor.

Stainless Steel Modulator Vacuum Line for all V8 engines with a C6 transmission except 429CJ or the 351C with a 4 barrel carburetor.

Reproduction Stainless Steel FMX Transmission Modulator Line for the 1972-1973 Mercury Cougar or Ford Mustang

Stainless Steel Transmission Modulator Line for the 1973 Mercury Cougar with a 351 Cleveland, a 4 barrel carburetor, and a C-6 Transmission.

Reproduction OE Steel Transmission Modulator Line for the 1972-1973 Mercury Cougar or Ford Mustang with a 351 and a FMX Transmission.

OE Steel Transmission Modulator Line for the 1973 Mercury Cougar with a 351 Cleveland, a 4 barrel carburetor, and a C-6 Transmission.