All Available Parts - 1972 Mercury Cougar

Replaces Ford Part #: D1ZZ-6221813-A

Replaces Ford Part #: D1ZZ-6221812-A

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. If you don't mind have having a different key for the door locks, this product might just work out.Attention potential buyer! This item will likely give you problems and be a general disappointment. Reviews show that the fitment is fair, and you will not be able to have these lock cylinders re-pinned, to use your original Ford key. One...

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Latch rod that links the door latch and the inside door handle, driver side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521941-A.

Inside door handle release mechanism for the driver side on 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This style was used after 9/15/1971. It...

Inside door handle release mechanism for the passenger side on base model standard 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the base door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with detachable arm rests, instead of the molded arm rests on the door panels, as found on the XR7 and Decor...

Inside door handle release mechanism for the passenger side on 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This style was used after 9/15/1971. It...

Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.

Found on the lower right corner of all 1971 - 1973 Cougars equipped with the XR7 Interior package. Both mounting studs will be in place and it will have a nice overall finish. Ford engineering number as seen on the backside is D1WB-65061A58-AA.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

Reproduction barrel nut or insert for attaching "Cougar" fender script to the fenders. Each Cougar emblem uses 4 of these barrel nuts which insert into the fender first, and then the Cougar emblem. Additionally, these nuts also go into the C pillars for attaching the XR7 badge or medallion on each side. Two barrel nuts per side for the XR7 medallions. Barrel nuts sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Note that if you want to replace these emblems...

Tubular or barrel nut for attaching our reproduction "C" pillar XR7 emblems with studs. We found these fasteners to install the emblems without disturbing the headliner of a 1967-68 Mercury Cougar. These are also suitable for installing this emblem onto the trunk lids of 1971-73 Mercury Cougar XR7 models. The originals were flat backed and glued onto the deck lids with adhesive. These tubular nuts require two 7/32" holes be drilled. These mount on the lower part of the roof behind the...

Used driver side (left hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used passenger side (right hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually.

This used grade A emblem will have good chrome and mounting studs and plexi center. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

Used on Cougars with no factory Air Conditioning. Located in the top center of the dash, ford engineering number on the backside is D1WB-65042A88.

This is the foil insert / decal found on a non XR7 Cougar. It's located just below the center rectangular dash vent / register. It measures 6" X 3/8".

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Reproduction manually adjustable convex passenger side view mirror in chrome for the Mercury Cougar or Ford Galaxie.  Gasket and screws included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Great reproduction of a rather hard to find part.

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Our used center grill emblems will always have some amount of fade in the plexi area and if the backing has not separated from the rest of the emblem it often times will be lose. We have had good luck filling the backside with epoxy glue. The engineering number as seen from the rear is D1WB-8216-BB.Ford part number D1WY-8A223-B ...

This used grade B emblem will have good chrome and mounting studs, but the plexi center will be faded. These can be opened up and repainted from the backside. The paint can be obtained from stores that sell modeling supplies. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. ...

These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter emblem is a much better buy . ...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Reproduction manually adjustable side view mirror in chrome for the Mercury Cougar and Ford Galaxie. This ambidextrous mirror works on either the passenger or driver side door and a gasket is included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino.The mounting screw, that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...

Used Grade "B" center grille emblem for the 71 - 72 Standard Cougar. Will have fading, pitting and the plastic lens area will need to be restored. Ford part number D1WY-8A223-A

Good working used mirror with joystick intact and no cracks in the base. The mounting holes on the base are located 6 3/4" apart. Ford number inside the base D1WB-17743. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Do you have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! Check out this video Check out...

Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Reproduction passenger side (right hand) manually adjusted sport mirror for the Mercury Cougar or 1970-1971 Ford Torino / Cobra / Ranchero / Cyclone. Our kit includes everything needed to mount a bullet style sport mirror to the passenger side of your vehicle. This reproduction unit is far more durable than the originals which were cast with a softer metal. The Ford service replacement part number for the original complete assembly was D0OZ-17682-D. The base in...

Reproduction convex lens for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. The screw that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B This version included the words "objects in mirror are closer than they appear". We also sell the...

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

This unique gasket is only slightly different from the driver side. The angle at the front is just a little different and notice it does not have a hole drilled for the remote mirror cable used on the driver side. This gasket was also used on the 1971 Ford Torino / Ranchero and Mercury Cyclone. This is an upgrade over the reproduction we carry for a 1969 - 1970 Cougar that has a passenger side Sport Mirror. The Ford Engineering number seen on the pad reads D1OB-17724-AA. Do you have questions...

Pan head screw for attaching the sport mirror glass assembly into the passenger side painted sport mirror head. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. 8-32 pan head screw with Phillips screw head. Do you have questions about installing a passenger side mirror or using Riv-Nuts? ...

Reproduction manually adjustable side view mirror in black for the Mercury Cougar and Ford Galaxie. This ambidextrous mirror works on either the passenger or driver side door and a gasket is included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...

These original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Includes 4 cut to length hinge pins and 8 hinge bushings. Replaces Ford Part #: C9ZZ-6522800

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522811-A

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522810-A.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522800-A.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522801-A.

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

These are identical on the driver and passenger sides.  Two required per car, sold individually. Dimensions: 9" x 3 1/2" Replaces part #: D2ZZ-18978.

Used original driver side (left hand) key lock to latch door lock rod for anu 1971-73 Mercury Cougar or Ford Mustang.Ford part # D1ZZ-6522135-A.

Used original passenger side, (right hand) key lock to latch, door lock rod for any 1971-73 Mercury Cougar.Ford part # D1WY-6522135-B.

Ford calls this Rod - Door Latch Push Button. This is the driver side manual door locking rod. Side specific to the driver side on any 1971-73  Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number D1ZZ-6521853-A.

Ford calls this Rod - Door Latch Push Button. This is the passenger side manual door locking rod. Side specific to the driver side on any 1971-73  Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number D1ZZ-6521852-A.

Used original door latch actuating rod for either the driver side (left hand) or the passenger side (right hand) of the Mercury Cougar. Attaches to the outside door handle and the door latch mechanism.Replaces Ford part number D1WY-6522152-A.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1971-73 Mercury Cougar and Ford Mustang.

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits driver side doors of 1971-73 Mercury Cougar and Ford Mustang.

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...

Used on both the front and rear of the 1971-1972 Mercury Cougar produced before 10/1/71. The picture above shows the difference between the early version (right) and the later version (left). Plan on purchasing new knobs to go with the bare crank, we have 7 different colors to choose from. See related items. Inquire about a B grade knob if you are looking for something just so that you have a window crank. Ford Part # D0AZ-7630322-A, casting # as seen on the back D1AB-7630322-AWA. ...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms.  Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.   These pictures show what every 69-70 door panel looks like on the...

Reproduction window crank used on front doors of cars produced after 10-1-71 with no factory door speakers. Replaces Ford part number D2AZ-7630322-AOriginals have a casting number of D3AB-6523342-AA.

This handle is an excellent reproduction and features a brightly polished chrome finish.

This handle is an excellent reproduction and features a brightly polished chrome finish.

Reproduction Right Hand / Passenger Side Outer Door Handle for the 1971, 1972 and 1973 Mercury Cougar.

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1971-73 Mercury Cougar and Mustang. This particular switch is also found on various other Ford/Mercury products starting in 1970. Ford part number D0AZ-15A851-A.Includes bolt to attach to emergency foot brake.

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

If your original is pitted or has come apart this will easily snap in place to remedy the problem. The finish on the repro differs a little from original.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1971-73 Mercury Cougar used part number D0DF-13801-A Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Used water pump pulley used on 1970-73 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. This pulley is 5-15/16 inches in diameter. Pulley stamped C9OE-8509-F.

Single sheave pulley 6-61/64 inches in diameter. This pulley is designed to run on the inner most belt plane next to the water pump. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number D1AE-8509-BA....