All Available Parts - 1970 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 801-900 of 3357
Sorted By:
Availability:
Display Options:
Availability: Ships Direct from Supplier (Except International)
Item #: 12146 -
This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission. Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift Linkage This is just the kit, and does not include the full transmission!
Availability: In-Stock Item
Item #: 30193 -
New reproduction insert for the Hurst shifter boots. This is designed to protect the integrity and lengthen the life of the rubber boot used to protect Hurst shifters with rectangular arms. After a while, your boot can become stressed and even begin to tear apart when the arm is shifted contantly. You must remove the shifter handle to install the support. You may need to trim into the reinforced area to get a good fit. Installs from the under side of the boot. Check out our video on rebuilding...
Availability: In-Stock Item
Item #: 30215 -
Reproduction flexplate reinforcing ring. Strengthens the area where the automatic transmission flexplate mounts to the crankshaft. 5.12" outside diameter3.34" inside diameter .060 inches thickFits: 352 390 427 428 429 460 with C6 and FMX transmissions.Replaces Ford part # B9AZ-6A6366-B
Availability: Used / Wrecking Yard Item
Item #: 30550 -
Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...
Availability: In-Stock Item
Item #: 32173 -
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1970 Mercury Cougar and Ford Mustang with 302, 351W, 351C, 390, 428CJ engines. AMK number F-1496.
Availability: In-Stock Item
Item #: 32174 -
AMK fastener kit for attaching transmission rubber mount. Nuts and washers to fasten to cross member, and bolts to attach to any automatic transmission on all 1970 Mercury Cougar and Ford Mustang with 302, 351W, 351C engines. AMK number F-1497.
Availability: Out of Stock
Item #: 33300 -
Core C-6 Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "U" transmission code on the door tag. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the special valve body for 1970 428CJ and 1971 429CJ engines. Ford...
Availability: Used / Wrecking Yard Item
Item #: 20457 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. Here is the 3M product used to glue this trim to the glass.
Availability: Used / Wrecking Yard Item
Item #: 20458 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. Here is the 3M product used to glue this trim to the glass. We also offer this item as restored. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar...
Availability: Used / Wrecking Yard Item
Item #: 27035 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. Here is the 3M product used to glue this trim to the glass.
Availability: In-Stock Item
Item #: 31654 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass
Availability: In-Stock Item
Item #: 31456 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass
Availability: In-Stock Item
Item #: 14212 -
Reproduction Replacement for the Rear License Plate Lens for the 1969 - 1973 Mercury Cougar or Ford Mustang. We also have good used original OEM lens that can easily be cleaned to look as good as these Chinese reproductions. Replaces Ford part #: C4AZ-13564.
Availability: In-Stock Item
Item #: 41087 -
Fits Standard and XR7
Sold as a Set as Pictured.
Availability: In-Stock Item
Item #: 10106 -
This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.
Availability: Used / Wrecking Yard Item
Item #: 30457 -
Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.
Availability: Out of Stock, On Order
Item #: 32951 -
These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific.
Availability: Ships Direct from Supplier (Except International)
Item #: 18890 -
This is the modern version of the Kelsey Hayes wheels that were originally equipped on 1967 Shelbys. One-piece cast aluminum structure with a CNC machined face and durable clear coat finish. The lighter weight one piece design also provides a significant weight savings over the original steel design, delivering improved acceleration and braking performance. These take specific lug nuts and center caps (sold separately, see related items). These wheels come with free chromed plastic center...
Availability: Ships Direct from Supplier (Except International)
Item #: 15838 -
Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...
Availability: In-Stock Item
Item #: 30523 -
This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with natural aluminum accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome...
Availability: In-Stock Item
Item #: 30714 -
Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...
Availability: Ships Direct from Supplier (Except International)
Item #: 31853 -
Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...
Availability: Ships Direct from Supplier (Except International)
Item #: 31854 -
Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...
Availability: Ships Direct from Supplier (Except International)
Item #: 32606 -
These T/A style wheels have the classic 8-spoke European design that was popular with road racers in the 60's and 70's. Fits the 60-73 Mustang, Falcon, Fairlane, Comet and 67 - 70 Cougar. Chrome plated plastic Legendary Wheel hubcap included. Back spacing on all Legendary wheels is 4 1/4". Bolt pattern 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. Check out our video on Legendary Wheels below: ...
Availability: Used / Wrecking Yard Item
Item #: 24776 -
This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall, look for two dimples. Wiring is simple, unplug the windshield wiper harness and plug the male and female ends into the appropriate plugs on the controller. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper delay switch.Part # C9ZB-17C476, MPC #'s C9ZZ-17C476-B or D0ZZ-17C476-B.
Availability: Used / Wrecking Yard Item
Item #: 25187 -
This used intermittent wiper switch has a two speed wiper function, and when turned counter clockwise, has a rheostat that sets the different delay times. A 1969 switch can be used, but the shaft will be about 3/8" shorter, you may need to use a 1969 metal knob to use in a 1970. Sometimes called interval or delay wipers.*NOTE* Must be used in conjunction with a Intermittent wiper controller.Replaces part # D0ZF-17A553-B, MPC # D0ZZ-17A553-A
Availability: Used / Wrecking Yard Item
Item #: 19553 -
This used conversion kit includes the controller and switch to convert your standard two speed wiper system over to delay wipers.Controller part # C9ZB-17C476Switch part # D0ZF-17A553-B, MPC # D0ZZ-17A553-A
Availability: Out of Stock
Item #: 13767 -
Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...
Availability: Used / Wrecking Yard Item
Item #: 25018 -
Used carbon canister filled with charcoal or carbon particulates for the Mercury Cougar or Ford Mustang. This unit mounts to or near the passenger side (right hand) engine frame mount. All 1970 California sold Cougars and Mustangs came with this canister to comply with California's strict emission standards. Ford part # D0AZ-9D653-C, casting # D0AF-9D653-C. *NOTE* These are 40 year old canisters, at this late stage the filtering ability of the particulates are probably not that...
Availability: Used / Wrecking Yard Item
Item #: 25009 -
D0AF-9E718-C Distributor modulator control module for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engines and FMX or automatic transmission. The 'black box', supposed to have a blue cover, The Autolite Shop Tips guide describes this box as having a blue cover and a stamped part number of D0AF-9E718-S. The Ford MPC shows a master part number of D0AZ-9E718-C, and a box marked D0AF-9E718-C.
Availability: Used / Wrecking Yard Item
Item #: 25005 -
Used distributor modulator thermal switch for the Mercury Cougar or Ford Mustang equipped with the M code 351C-4V engine and FMX automatic transmission. Originally this switch was mounted in the drivers side door jamb and had a bimetal strip that was calibrated for ambient temperatures between 50 and 58°F. We dont have a way to test these, so they are sold as is. Ford part # D0AF-12A164-B.
Availability: Used / Wrecking Yard Item
Item #: 25010 -
D0AF-9E731-A Distributor modulator speedometer cable speed sensor for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Mounts inline on a two piece speedometer cable. Ford master part number D0AZ-9E731-A.
Availability: Used / Wrecking Yard Item
Item #: 25072 -
D0OZ-12A163-B Paired steel tubes that run along the driver side valve cover. Used on the 1970 Mercury Cougar, Mercury Cyclone, Ford Torino, and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission.
Availability: Used / Wrecking Yard Item
Item #: 25251 -
D0ZZ-9A820-H Distributor modulator upper speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Cable that connects the back of the speedometer and the speed sensor of the modulation system. Shown to be 10.54 inches long. Please see D0ZZ-9A820-B or -G for the lower cable section.
Availability: Used / Wrecking Yard Item
Item #: 25245 -
D0ZZ-9A474-A Vacuum fitting for the rear of the intake manifold on a 1970 Mercury Cougar or Ford Mustang with the M code 351 Cleveland 4 barrel engine. Has two vacuum nipples or ports. 1970 Mercury Cougar Ford Mustang Modulation System - Bleed Assembly - Used
D0AZ-12A168-C Very small inline vacuum hose bleed valve assembly installed very close to the distributor modulator control box.
Availability: Out of Stock
Item #: 41609 -
Very nice reproduction of the ram air flapper vacuum motor. Application 1968-1/2 428CJ Cougar and Mustang, 1969-71 Mercury Cougar with ram air, and 1969 Ford Torino 428CJ ram air. Not for shaker ram air systems.NOTE: These are manufactured with an extra long shaft to allow you to trim for an exact fit.
Availability: Rare / NOS Part
Item #: 33100 -
NOS air cleaner breather element filters for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, cartridge holder not included.Packaging may vary
Availability: Rare / NOS Part
Item #: 33326 -
NOS air cleaner breather element filter assembly for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, "AUTOLITE" marked also FA-79. Casting number D0OF-9D696-A. Ford part number D0OZ-9D695-A.
Availability: Ships Direct from Supplier (Except International)
Item #: 11882 -
Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.
Availability: Used / Wrecking Yard Item
Item #: 24647 -
Applications all 1969 351 engines, both 351-2V and 351-4V, and 1970 351W-2V engines after 2/2/1970. That is correct, after Feb 1970 the H-code Windsor engined 351's used a 1969 style air cleaner snorkel.The C9OZ-9A626-B snorkel looks the same, but is a bit longer than the 1968 C8AZ-D snorkel. Probably due to the taller deck height of the 351 over the 302 engine, and or the heat shield design. Please note: Wax stat is not tested, nor can we test them, sold as- is. Click on images to enlarge. ...
Availability: Used / Wrecking Yard Item
Item #: 24448 -
For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.
Availability: Used / Wrecking Yard Item
Item #: 25100 -
Application is for the beginning of the 1970 model year and only for H-code 351W-2V. Windsor engines only, from inception until 2/2/1970. Ford part number D0OZ-9A626-B.
Availability: Used / Wrecking Yard Item
Item #: 15125 -
Application is for all 1970 351 Cleveland engines, both 2 barrel and 4 barrel. This air cleaner snorkel
is different from past years in that the opening is necked down and has a flared flange. It also has a small opening on the bottom for a metal "S" tube. Ford part number D0OZ-9A626-D. Click on images to enlarge. ...
Availability: Ships Direct from Supplier (Except International)
Item #: 25247 -
Although these are considered reproductions, they are actually put together from multiple parts of original excellent condition used snorkels. And, since there are multiple colors of Ford Blue, the supplier is leaving them as unpainted.Application would only be for 1970 Boss 302 Eliminators and Boss2 Mustangs. Ford part number D0ZZ-9A626-B.
Availability: In-Stock Item
Item #: 41713 -
Concours Correct Spring attaches snorkle thermo door to Snorkle Base Replaces Ford Part # C8AZ-9A652-B
Availability: In-Stock Item
Item #: 10061 -
Aluminum Preheater hose that is used to preheat carburetor air. This 2" X 18" aluminum flex / stretch type hose attaches from the exhaust manifold shroud to the bottom of your air cleaner snorkel. This hose is sold individually and does not come with clamps.If you prefer, you can grab the cloth type hose here. ...
Availability: In-Stock Item
Item #: 26883 -
Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...
Availability: In-Stock Item
Item #: 41350 -
Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds.
Availability: Used / Wrecking Yard Item
Item #: 25017 -
D0AZ-9A603-C This is a two piece metal shroud unique to early production 1970 H code 351-2V Windsor Cougars. Due to problems Ford had with this design they returned to the 1969 style later in the year (after 2-2-70). *Note - 1970 351-2V Windsor cars build before 2-2-1970 used a two piece heat shield. Also used air cleaner snorkel D0OZ-9A626-B and a paper 'S' tube. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts....
Availability: In-Stock Item
Item #: 14098 -
*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...
Availability: Ships Direct from Supplier (Except International)
Item #: 14051 -
*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ. Comes with brackets and hardware as shown. Click on images to enlarge. ...
Availability: In-Stock Item
Item #: 10714 -
Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.
Availability: Out of Stock
Item #: 18934 -
Grade B exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade B used will have minor pitting, and may have small holes and or rough rusted edges. When mounted it would be difficult to see the defects. We also stock A grade versions.Replaces Ford part number D0OZ-9A603-F.
Availability: In-Stock Item
Item #: 31171 -
Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S
Availability: Used / Wrecking Yard Item
Item #: 19124 -
Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.
Availability: Used / Wrecking Yard Item
Item #: 19125 -
Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.
Availability: Used / Wrecking Yard Item
Item #: 14570 -
This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring.
These will work on all 1967-70 as well. But...
Availability: Used / Wrecking Yard Item
Item #: 14571 -
This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area.
You can find the hood hinge apron nuts here. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with...
Availability: Used / Wrecking Yard Item
Item #: 14572 -
This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring.
These will also work on 1967-70 as well....
Availability: In-Stock Item
Item #: 11092 -
Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...
Availability: In-Stock Item
Item #: 10513 -
Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...
Availability: In-Stock Item
Item #: 10514 -
Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...
Availability: Used / Wrecking Yard Item
Item #: 20079 -
This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...
Availability: Used / Wrecking Yard Item
Item #: 31197 -
Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1969-70 Mercury Cougar and Ford Mustang. Ford part number C9ZZ-16A006-A passenger side, C9ZZ-16A005-A driver side.
Featured!
Availability: In-Stock Item
Item #: 25904 -
Sold as a pair, comes with stud and nut mounting kit. Correct for all 69-70 Mustang / Shelby / Standard Cougar convertibles. Replaces Ford part # C9ZB-76423A18-A & C9ZB-76423A19-A (Not for XR7). Are you thinking about installing a convertible top yourself? Check out our video below for help. ...
Featured!
Availability: In-Stock Item
Item #: 11370 -
Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...
Availability: In-Stock Item
Item #: 11377 -
These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...
Availability: In-Stock Item
Item #: 42013 -
This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.
Availability: In-Stock Item
Item #: 26059 -
Used to cushion and protect top vinyl from excessive wear from side rails. Unfortunately none of the reproductions that we have found resemble the OEM pads. OEM pads looked canvas on the under side that goes against the convertible top rails, and what looked like the soft side of a velcro strip on the upper side that makes contact with the convertible top itself. These are still highly recommended as they keep the convertible top rails from rubbing thorough the convertible top. "I found WCCC...
Availability: In-Stock Item
Item #: 42015 -
A quality rust proof stainless steel cable which features all the correct hardware. Sold as a pair. Replaces Ford Part #: C9ZZ-7652806-A.
Availability: Used / Wrecking Yard Item
Item #: 24791 -
C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.
Availability: In-Stock Item
Item #: 41978 -
Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650509-K. Casted Pot Metal with Engineering # C4ZB-7650535-C
Availability: In-Stock Item
Item #: 41972 -
Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650508-KCast Pot Metal with Engineering # C4ZB-7650534-C
Availability: Used / Wrecking Yard Item
Item #: 19495 -
No damage original bolt. Sold individually, two required per car.
Availability: Ships Direct from Supplier (Except International)
Item #: 41973 -
Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.
Availability: In-Stock Item
Item #: 19362 -
Exact fit, not generic 'One Size Fits All' hoses. Quality high pressure fittings. Contains both the upper and lower Hydraulic Hose for a 1969 or 1970 Mercury Cougar or Ford Mustang Convertible Hydraulic Cylinder.
Availability: In-Stock Item
Item #: 20375 -
Not quite as long as the original bushing, but will work. If you want the correct one, we occasionally get in the NOS version of this bushing. Call us for the availability of the NOS bushing. Replaces Ford Part #: C3AZ-5422841-A.
Availability: Used / Wrecking Yard Item
Item #: 18542 -
Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...
Availability: In-Stock Item
Item #: 15862 -
Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.
Availability: Used / Wrecking Yard Item
Item #: 19348 -
This is the stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Stang. This is a very hard part to come by in good shape. Many times body shops will loose this piece while replacing the top. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...
Availability: Used / Wrecking Yard Item
Item #: 25090 -
This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...
Availability: In-Stock Item
Item #: 25905 -
Metal strip that fastens the weatherstrip to the bottom side of the header bow.
Availability: Used / Wrecking Yard Item
Item #: 15462 -
This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.
Availability: Used / Wrecking Yard Item
Item #: 20200 -
This four used piece wiring kit gives you all the factory correct wiring unique to a 1969 XR7, 1969 standard or 1970 standard convertible. This IS NOT correct for a 1970 XR7 convertible. The rocker switch that raises and lowers the convertible top for the 1970 XR7 convertible is a unique design and uses a different plug to mate to it, as well as it uses a circuit breaker rather than a fusible link on the power feed.Fits:1969 Mercury Cougar Standard Convertible1969 Mercury Cougar XR7...
Availability: Used / Wrecking Yard Item
Item #: 11323 -
C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Receptacle only, sliding covered retainer sold separately. Also fits 1965-68 Ford and Mercury full sized convertibles. Decades old gum stuck to the bottom is no extra charge...
Availability: In-Stock Item
Item #: 14751 -
Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Very nice reproduction item, comes as shown with the knob marked "TOP". *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.
Availability: In-Stock Item
Item #: 12-3008 -
New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...
Availability: In-Stock Item
Item #: 41980 -
Connecting to the Convertible Frame Lift Lever and the Convertible Hoses, the Convertible Top Hydraulic Cylinder creates pressure from the fluid transferred by the hoses. Each Hydraulic Cylinder consists of light-weight aluminum casing, a durable steel rod, and includes all bushings and gaskets. Part is made through innovative engineering and rigorously tested to provide you with the best in functionality and long-term dependability. Precisely crafted with high grade materials...
Availability: In-Stock Item
Item #: 42210 -
Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.
Availability: Ships Direct from Supplier (Except International)
Item #: 11611 -
We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...
Availability: Ships Direct from Supplier (Except International)
Item #: 11612 -
We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...
Availability: Ships Direct from Supplier (Except International)
Item #: 11614 -
We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...
Availability: Ships Direct from Supplier (Except International)
Item #: 11615 -
We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...
Availability: Ships Direct from Supplier (Except International)
Item #: 11617 -
We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...
Availability: In-Stock Item
Item #: 10475 -
Keeper or retainer for attaching the convertible top cylinder pins. These are usually broken when replacing convertible top cylinders. One retainer per side
Availability: Out of Stock
Item #: 10749 -
Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles. Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider. The colors don't always...
Availability: In-Stock Item
Item #: 14-0001 -
This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...
Availability: Used / Wrecking Yard Item
Item #: 26930 -
Used passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...
Availability: In-Stock Item
Item #: 27118 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part. Ford...
Availability: In-Stock Item
Item #: 27119 -
Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored passenger side (right hand) vertical windhield moulding / trim for the Mercury Cougar. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part. Ford part # C9ZZ-7603144-B....