All Available Parts - 1970 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 3101-3200 of 3357
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 31304 -
Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.
Availability: Out of Stock
Item #: 12418 -
Used driver side (left hand) and passenger side (right hand) convertible top boot moulding / trim for the standard Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Ford part # C9ZB-76423A19-A driver side, C9ZB-76423A18-A passenger side. *NOTE* If you have questions about your cores, checkout our video below. ...
Availability: Out of Stock
Item #: 24790 -
C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.
Availability: In-Stock Item
Item #: 23892 -
C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.
Availability: Out of Stock
Item #: 19403 -
This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford casting number C9ZB-76514A72-A
Availability: Out of Stock
Item #: 15461 -
This short section of wiring attaches to the terminal post on the starter solenoid that faces towards the firewall. The other end is a female plug that incorporates a fusible link. If your switch were to get stuck or the frame got in a bind with continued power being applied this is the portion that would blow saving you from a costly wiring "melt-down". This same part was used on both XR7 and standard Cougars with a power sunroof or convertible top.
Availability: Out of Stock
Item #: 17-0002 -
This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...
Availability: Out of Stock
Item #: 19507 -
Good used plastic trim that will need repaint, and the screw hole hidden behind dash pad is almost always cracked.Ford Part #: C9ZZ-7603598-A, stamped with C9ZB-7603598-AW-R.H. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...
Availability: Out of Stock
Item #: 19503 -
Good used plastic trim that will need repaint, and the screw hole hidden behind dash pad is almost always cracked.Ford Part #: C9ZZ-7603599-A, stamped with C9ZB-7603599-AW-L.H. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...
Availability: Out of Stock
Item #: 20425 -
Good used metal strip that fastens the weatherstrip to the bottom side of the header bow. Keep in mind we have (almost) every single used part related to the 69-73 Convertible Cougar and convertible Ford Mustang / Shelby in stock at all times.
Availability: Out of Stock
Item #: 24870 -
This is the trim piece the goes across the top on the inside of the windshield. This piece will need to be sand blasted and repainted. Many people have chromed these, but from the factory they were painted satin silver.Ford Part #: C9ZZ-7603606-B
Availability: Out of Stock
Item #: 41948 -
These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.
Availability: Out of Stock
Item #: 22632 -
OEM Ford factory cowl brace as found on 1970 Mercury Cougar Boss 302 Eliminator and Boss 302 Mustang. Used item, not reproduction. Mounts with the lip up, towards the front of the car. Very limited supply.
Availability: Out of Stock
Item #: 24883 -
Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.
Availability: Out of Stock
Item #: 21619 -
Used door hinge anchor plate for attaching the door hinge to the body pillar. All positions are the same, upper, lower, driver and passenger sides. Fits all 1969-70 Mercury Cougar and Ford Mustang.Ford part number C9ZZ-6502666-A.
Availability: Out of Stock
Item #: 14573 -
This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....
Availability: Out of Stock
Item #: 25099 -
Grade A exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade A used will only have minor pitting, it will have no holes or rough rusted edges. We also stock B grade versions for less than half the money.Replaces Ford part number D0OZ-9A603-F.
Availability: Out of Stock
Item #: 25096 -
D0OZ-9652-A Heat shield 'S' tube unique to 1970 351 Cleveland engines 2v or 4v. *Note - Must be used in conjunction with the heat shield part number D0OZ-9A603-F and air cleaner snorkel part number D0OZ-9A626-D.
Availability: Out of Stock
Item #: 25246 -
Ford part number D0ZZ-9A603-C for the upper section and Ford part number D0ZZ-9A603-D for the lower section of this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - 1970 Boss 302 cars build after 9-2-1969 used this lower section. of a two piece metal shroud unique to G code Boss 302 Cougar Eliminators.
Availability: Out of Stock
Item #: 42380 -
Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...
Availability: Out of Stock
Item #: 42381 -
Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...
Availability: Out of Stock
Item #: 24646 -
Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...
Availability: In-Stock Item
Item #: 30827 -
Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...
Availability: Out of Stock, On Order
Item #: 10666 -
New air cleaner breather element for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, includes cartridge holder, retainer clip and filter.
Availability: Out of Stock
Item #: 41458 -
Fits all V8s with oval air cleaner.
Availability: Out of Stock
Item #: 20527 -
Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...
Availability: Out of Stock
Item #: 24447 -
C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.
Availability: Out of Stock
Item #: 25249 -
D0ZZ-9A820-B Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured before 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 45.25 inches long. Please see D0ZZ-9A820-H for the upper cable section.
Please see D0ZZ-9A820-G for cars manufactured after 12-15-1969.
Availability: Out of Stock
Item #: 25250 -
D0ZZ-9A820-G Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured after 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 49.24 inches long. Please see D0ZZ-9A820-H for the upper cable section.
Please see D0ZZ-9A820-B for cars manufactured before 12-15-1969.
Availability: In-Stock Item
Item #: 10722 -
D0ZZ-9D664-A Bracket for mounting the charcoal canister to the body. Application - all 1970 California sold Mercury Cougar and Ford Mustangs. Some Ford illustrations show a casting number of D0ZF-9D664-A
Availability: Out of Stock
Item #: 25025 -
Valve assembly for venting the fuel tank with evaporative emission controls systems found on cars originally sold in California. 1970 Mercury Cougar and Ford Mustang with 'EC' on the body buck tag. This listing is for a valve assembly without broken nipples. Very hard to find in unbroken condition. We can often supply this valve assembly with a broken nipple for substantially less money. Picture shows the additional fitting, which may or may not be available. Replaces Ford part...
Availability: Out of Stock
Item #: 25135 -
This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. Replaces part # D0WY-15702-A
Availability: Out of Stock
Item #: 18889 -
This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...
Availability: Out of Stock
Item #: 14-0055 -
Silicone and fasteners, everything needed for installation of our seat divider panel.
Availability: Out of Stock, On Order
Item #: 32368 -
Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...
Availability: Out of Stock
Item #: 23230 -
Older used aluminum intake manifold. Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.
Availability: Out of Stock
Item #: 15998 -
Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. You can use this 3M product to glue this trim to the glass. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...
Availability: Out of Stock
Item #: 22957 -
The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...
Availability: Out of Stock
Item #: 14-0031 -
New RTV oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.
Availability: Out of Stock, On Order
Item #: 14-0024 -
New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...
Availability: Out of Stock
Item #: 31044 -
We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...
Availability: Out of Stock
Item #: 12-3009 -
New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...
Availability: Out of Stock, On Order
Item #: 26657 -
These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up. Plug size: 1 1/2" also used for the electric headlight conversion kit for the firewall pass through body plug.
Availability: Out of Stock
Item #: 42189 -
These are always rock-hard so if you plan on removing a seat and do not want to boil your old rubber parts to make them pliable enough to reinstall then you will want to pick a set of these up.Plug Size 1 1/2"
Availability: Out of Stock, On Order
Item #: 31364 -
Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang.
Availability: Out of Stock
Item #: 19984 -
New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.
Availability: Out of Stock
Item #: 12844 -
Much better fit than the reproductions which make closing your door very difficult for the first year.Ford part # C9ZZ-7602627-A
Availability: Out of Stock
Item #: 12845 -
Much better fit than our reproductions which make closing your door very difficult for the first year. Ford part # C9ZZ-7602626-A
Availability: Out of Stock, On Order
Item #: 13627 -
Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.
Availability: Out of Stock
Item #: 11-0225 -
This is the rubber that goes into the bracket of the bottom of the center of the door, for 1970 bolt-in door glass. Note that this bumper is substantially taller than the 69 version. See C9ZZ-6521762-A for the 1969 glued-in door glass version. If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will need to make sure you have the correct version of this part for the type of glass...
Availability: Out of Stock, On Order
Item #: 26523 -
New and improved reproduction bottom of the door seal for the 1967 - 1970 Mercury Cougar or Ford Mustang. Unlike previous versions, these are now made with denser material and are much more rigid. They measure 38" for 1967 -1968 and 41" for 1969-70 so you will have to trim them down if you have a 1967-68. One of the most common missing parts on a 1967-70 Mustang or Cougar today is the lower weatherstrip seals on the doors. These seals were added to cars to keep dirt and moisture from entering...
Availability: Out of Stock, On Order
Item #: 14172 -
This is identical to the 67 pad just slightly wider. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part number D3ZZ-2454-A
Availability: Out of Stock, On Order
Item #: 27549 -
New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.
Availability: Out of Stock
Item #: 26227 -
Good fit, includes all hardware shown. We've found that when using our reproduction drop down bracket (for those with headers), the bushings in this kit will rip and tear through the oversized hole, so you can also purchase the pair of the premium polyurethane bushings and the issue will go away. Otherwise you can go with our premium version boot kit of you need internal parts for the cylinder. Replaces Ford Part #: C6OZ-3C651-A ...
Availability: Out of Stock, On Order
Item #: 26572 -
Reproduction Clutch Pedal Rod To Firewall Seal. Replaces Ford Part #: C6OZ-7533.*NOTE* From personal experience we have found these do not stay attached to the firewall as well as the originals. An adhesive will remedy this problem.
Availability: Out of Stock, On Order
Item #: 26662 -
If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.
Availability: Out of Stock
Item #: 32776 -
C9ZZ-18A318-C New Old Stock vacuum control motor for factory air conditioning on all 1969-70 Mercury Cougar and Ford Mustang.Tested and works perfectly. Has attached extension marked C9ZA-18A318-J.
Availability: Out of Stock
Item #: 41542 -
Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock, On Order
Item #: 26576 -
Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.
Availability: Out of Stock
Item #: 19414 -
Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.
Availability: Out of Stock, On Order
Item #: 26221 -
Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...
Availability: Out of Stock
Item #: 33335 -
New Old Stock NOS passenger side front turn signal assembly. Bezel, lens, housing. 1969-70 Mercury Cougar and Shelby Mustang. Ford part number C9WY-13210-A, casting number C9WB-132_7.
Availability: Out of Stock
Item #: 33640 -
Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.
Availability: Out of Stock
Item #: 33465 -
NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.
Availability: Out of Stock
Item #: 33466 -
NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.
Availability: Out of Stock
Item #: 33229 -
Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available. NOS power steering control valve repair kit. Ford part number C2AZ-3A553-A.
Availability: Rare / NOS Part
Item #: 32860 -
New old stock manual steering worm gear for any 1967-70 Mercury Cougar or Ford Mustang with manual steering or 19:1 steering gear box. Factory new worm gear assembly for rebuilding your steering gear box. NOS in the box Ford part number C7ZZ-3524-C. ...
Availability: Out of Stock
Item #: 32769 -
New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.
Availability: Out of Stock
Item #: 20174 -
This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...
Availability: Out of Stock, On Order
Item #: 12128 -
Timing chain set for your 67 - 72 Cougar or Mustang equipped with the 302 Engine.Gears (sprockets) are made from high alloy steel, and heat-treated for durability. Chain is pre-stressed and heat-treated for longevity.
Availability: Out of Stock
Item #: 12835 -
Used stamped steel pointer mounts to timing chain cover. Correct for 1970 Mercury Cougar with 351W engine, and 1970-72 Ford Mustang 302 and 351W. At least two distinct versions of this pointer may be availbable. Starting in 1970, Ford V-8 engines had timing pointers installed on the passenger side of the engine, and a companion harmonic balancer with 4 bolts for attaching crank shaft pulleys. Uses two of the timing cover bolts for attaching. Replaces Ford part C9TZ-6023-A. This icon means that...
Availability: Out of Stock
Item #: 25235 -
D0ZZ-7210-B Chromed "Hurst" labeled shifter for all 1970 - 1971 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. The 1970 Ford master part number is D0ZZ-7210-B, 1971 is D1ZZ-7210-A. These shifters originally came with the "Hurst" T handles installed. These shifters will not come with a "T" handle. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10982 -
D0ZZ-7400-A 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10970 -
D0ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-4V engine. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10983 -
D0ZZ-7400-D Hurst built 4 speed manual shift control assembly for any 1970 - 1971 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10971 -
Used Hurst built 4 speed manual shift control assembly for the Mercury Cougar or Ford Mustang equipped with the manual transmission. This assembly includes the shifter mechanism, shift rods, and shift lever. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. This unit may be used for the 1971 edition and is in good used condition.Ford part # D1ZZ-7400-B. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 23842 -
Good used single sheave pulley for the alternator on the Boss 302. Ford Part #: C5AF-10A352-H.
Availability: Out of Stock
Item #: 20112 -
Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B
Availability: Out of Stock
Item #: 11035 -
Cast iron construction similar to the 1969 bracket but with a design change for 1970. We suspect that the change was made for the new pulley and bracket arrangement starting in 1970. Ford part number D0ZZ-9B450-B.
Availability: Out of Stock
Item #: 11036 -
Used adjusting bracket for the Thermactor air pump for the Mercury Cougar or Ford Mustang equipped with the 302 Boss engine.Ford part # D0ZZ-9B452-A, casting # D0ZE-9B452-A or D0ZE-9B452-B.
Availability: Out of Stock
Item #: 25184 -
1970 Boss 302 Eliminator (G code engine). 3 Bolt smog pump pulley. Ford part number D0ZZ-9B447-A.
Availability: Out of Stock, On Order
Item #: 16789 -
Single cylinder head from 1968-70 Mercury Cougar with 428CJ engine with smog holes. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.09 and 1.65 inch valves, and the chambers measure out at 73-76cc's. With stock pistons, these heads will net an approximate compression ration of 10.6:1. Basic cylinder head number is 6090. These are the Cobra Jet exhaust manifolds with 16 drilled and tapped exhaust bolt holes. We won't have these in stock...
Availability: Out of Stock
Item #: 25695 -
Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code H 351-2V, engine code M 351-4V, and engine code G Boss 302 Eliminator only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D0ZZ-7003-D. Casting #'s RUG-AV or RUG-AV1.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...
Availability: Out of Stock
Item #: 25697 -
Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code H 351-2V, engine code M 351-4V, and engine code G Boss 302 Eliminator only. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear.Ford part # D0ZZ-7003-E. Casting # RUG-AW or RUG-AW1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...
Availability: Out of Stock
Item #: 10945 -
Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code Q 428 Cobra Jet. Additionally 1971 Mercury Cougar with engine code J 429 Cobra Jet and engine code C 429 Cobra Jet. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. The tailshaft on this transmission has a different bolt pattern for the Hurst shifter plate.Ford part # D0ZZ-7003-H. Casting numberRUG-AZ or RUG-AZ1.*NOTE* Technically...
Availability: Out of Stock
Item #: 32093 -
Used OEM Ford 428 Cobra Jet manual transmission flywheel. Stamped C8OE-A. Needs a ring gear, has chipped teeth. No visible issues, no discoloration from heat. Ford 428CJ only, not for 428 SUPER COBRA JET engines. This flywheel on a 428CJ is externally balanced. Should have 184 ring gear teeth.Ford part number C8OE-6380-A.
Availability: Out of Stock
Item #: 32781 -
NOS Key reminder buzzer for 1970-71 Mercury Cougar and Ford Mustang. Also used on 1970-72 Lincoln MKIII and Thunderbird. Can also be stamped DOAB-13150-B, DOAB-13150-E, and DOAB-13150-F. Ford master part number D0AZ-13150-E. NOTE: This buzzer is for ignition key reminder with two posts. The four post ignition / headlight buzzer can be found here. Click on images to enlarge. ...
Availability: Out of Stock
Item #: 32778 -
(7526) Nylon plastic injected. New Old Stock. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these. Replaces Ford Part #: C0AZ-7526-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they where...
Availability: Out of Stock
Item #: 32783 -
New old stock rubber fender to hood bumpers. Set of 4 NOS Ford. Replaces Ford part #: C6OZ-16758-A.
Featured!
Availability: Out of Stock
Item #: 32782 -
New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 32788 -
New old stock ashtray for any 1969-70 Mercury Cougar or Ford Mustang with factory console. This is the rear ash tray. Ford part number C8AZ-6262876-A.
Availability: Out of Stock
Item #: 32789 -
New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.
Featured!
Availability: Out of Stock
Item #: 32748 -
New old stock power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch. Stamped C8AB-14529-A. This is the 1 tab switch. However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.
Availability: Out of Stock
Item #: 32753 -
D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. NOS Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.
Availability: Out of Stock
Item #: 53206 -
[No Description Provided]
Availability: Out of Stock
Item #: 42368 -
Great addition to that show quality FE powered early Cougar. Unlike the reproduction this has the original part number, BARNUM BROS. FIBRE CO. INC. lettering and FoMoCo insignia at the top driver side. This was one of the last units out the door when FORD discontinued them in the 1990's. Weighs 2.70 pounds and the reproduction weighs 1.54 pounds. Ford part number C8ZZ-8146-A
Availability: Out of Stock
Item #: 10522 -
Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. New Old Stock OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder. Thread pitch 1/2" x 20
Availability: Out of Stock
Item #: 25853 -
NOS Ford key blank for trunk and glove box.Sold Individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but...
Availability: Out of Stock
Item #: 22225 -
NOS oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil pressure...
Availability: Out of Stock
Item #: 32729 -
Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.