All Available Parts - 1970 Ford Mustang

FEATURES : KHE 300-USB Features: * Wireless Bluetooth; * Mini SD Card Reader; * USB Flash Drive; * 6 AM/6 FM Preset; * Manual Up/Down Tuning; * Seek Auto Tune; * Auto Stereo/Mono; * Preset Scan and Auto Store; * Front/Rear Fader Control; * On/Off Volume Control; * Separate Bass/Treble Control; * Left/Right Balance Control; * Auto Antenna Power Lead; * LCD Display with Blue Back Lighting; * Aux Input Rear; * Frequency Selector. Size: N/A * Output: 50 Watt x 4 Channel * System Power: 200 Watts...

Secretaudio SST is a hidden audio system that offers great flexibility for mounting in any type of vehicle. The main receiver/amplifier unit is usually hidden under the seat, or behind the dash. A 10ft cord from the Tuner/Amp plugs into a LCD display. The system can be operated from up to 40 feet away with the included RF (radio frequency remote.) Included with the system is a flush mount bezel for console or dash mounting. The small dimensions of the flush mount system allow you to install...

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

These anti static devices were installed under the front bearing dust caps on cars equipped with factory installed AM-FM radios. The part pictured is NOS, the one we currently have in stock is used. Sold individually.

Hard to find little detail item that is often times missing and is correct for Ford Mustang as well.

Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work.

C6OA-18832-A is the number stamped into the end of the Autolite capacitor. Attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. Application all Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory.. Starting in 1972 there is a Motorcraft version...

Correct plug for your 1967 - 1973 Mercury Cougar or Ford Mustang. Often these have been cut from the main loom to install an after market radio.

Reproduction radio plug and pigtail for your 1967 - 1971 Mercury Cougar or Ford Mustangs.

Correct plug for your 67-71 AM- FM radio, or 8-track... Often these have been cut from the main loom to install an after market radio.The 1972 model used the same plug, but the wires are not in the same spots, go figure! These are speaker wires not power wires.The color codes are:  White right cowl speaker.   Orange left cowl speaker. Speaker blue / black ground. Power "not this listing." Blue / red stripe, radio light. Yellow / black stripe, power in for radio. ...

If after installing a new stereo system you experience unwanted motor whine or engine noise, check all grounds on radio, amp, etc. If you still have the noise, this filter may help.Instructions included.

This plate allows you to install (2) 3 1/2" speakers of your choice in place of the (1) original factory speaker in the dash of your Cougar or Mustang. This is the same plate used on the Kenwood and Pioneer Dual Dash Speaker kits. Check out this video

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Features two 4 ohm 3 1/2" coaxial two way speakers. Huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with or without in-dash factory AC. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Quality Kenwood speakers that features two 40 watt 3 1/2" coaxial two way speakers. this unit is a huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with in-dash factory AC or not. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

Exact replacement for that valuable AM-FM radio. This plug and pigtail is used to repair the radio out to speaker wiring so that it will plug into the plug for the speakers. Don't fake it and hack up your valuable under-dash wiring harness to make your original radio work! Fix it correctly the first time with this quality replacement piece.

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

New set of 8 chrome headed screws for installing original or reproduction door speaker covers on all 1969-70 Mercury Cougars and Ford Mustangs.

Original used AM radio speaker lead wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustangs with factory AM radios. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios

Original used AM radio power lead wiring harness pigtail for the 67 - 71 Mercury Cougar and Ford Mustangs with factory AM radios. This double male plugged wiring pigtail solders to the your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios.

Original used speaker lead wiring harness pigtail for all 69 - 70 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the door.*Note - The only difference between this pigtail and the one listed for the 1967-68 dash speaker is the actual plug design.

Not sure of the exact application for these original Ford stereo speaker wiring harnesses. We think that they may have come from the radio kits installed by Ford and Mercury dealers. Note the special speaker connector plugs. The individual right and left speaker wiring leads are about 40 inches in length from the center plug that goes to the radio or stereo. The paper tags are missing from these harnesses, but we are pretty sure that they begin with C8OA-19A041.One of our customers says that...

Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work. New Old Stock switch. Ford part number C7AZ-18972-A and C7AA-18972-A on the wiring tag. NOS

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides of Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Replaces Ford part # C7ZZ-2078-A.

Flexible high pressure replacement brake hose for the front driver (left hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-B.

Flexible high pressure replacement brake hose for the front passenger (right hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-A.

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with power drum brakes. These are brand new units, not rebuilt, and are made from high quality American made parts. WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...

Used short style brake pedal for the Mercury Cougar and Ford Mustang equipped with an automatic transmission and manual drum brakes on all four wheels. The picture may show hardware and pedal pad with trim, but the pedal is shipped bare. Ford part # C9ZZ-2455-C.

Used brake pedal for the Mercury Cougar or Ford Mustang equipped with a manual transmission and drum brakes. This unit is for use with a clutch pedal and has a shorter arm than power brake pedals. The brake pedal is shipped bare. Fits any 1969-70 Mercury Cougar or Ford Mustang.Ford part # C9ZZ-2455-B.

Reproduction drum brake pedal pad for the Mercury Cougar or Ford Mustang equipped with an automatic transmission. The 1967 version of this piece is narrower than this 1968-73 piece.Replaces Ford part # C6OZ-2457-A.

These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

Bolt and nut for installation of disc brake pedals in any 1967-73 Mercury Cougar or Ford Mustang. See related items for plastic bushings and metal spacer.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.

Reproduction driver side drum brake spindle. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction pair of drum brake spindles. These are getting hard to find in used condition, considering the after market disc brake conversions that require the use of 1970 drum brake spindles. 1970 was a heavier design over 1968-69. Fits 1970 - 1973 Mercury Cougar, Ford Mustang, and mid sized Ford's such as Torino, Ranchero, Cyclone, etc.

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

Reproduction 161 Exterior Side Marker Light Bulb for the 1969 and 1970 Mercury Cougar

Reproduction 257 Door Ajar / Park Lamp Light Bulb for the1969 and 1970 Mercury Cougar

Plastic power window switch holder for the drivers door. This is the master switch holder or sleeve as it is called in the master parts catalog. Used starting in mid year 1970 through 1972 on Cougars, 1971-72 Ford Mustangs, and many 1970 full sized Ford and Mercury cars. Sleeve sold as is, without internal buss bars or mounting clips. Used, often times one of the tabs is broken, still functional, may need a bit of glue or tape to keep closed. Comes with the rear cover. *Warning - Take a...

Reproduction power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch.However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

Reproduction two tab power window switch for the master switch panel on the drivers door of mid 1970-72 cars. Research shows this switch was used in the master control panel on the drivers side door. With the mid to late1970-1972 and later power window systems. Compare your switch to these to insure you have the right configuration.However, for a 1969 and early 1970 master switches use a C9AZ-14529-D switch. That switch is also available, see related products tab.

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Voltage regulator for the 1968, 1969, and 1970 manufactured before 9/15/1969 that is not equipped with factory AC. This regulator has "C8AF-10316-A" printed on to it, actual Ford Part number is C3SZ-10316-B or D4TZ-10316-A. This is Ford Regulator Number GR-341. These new voltage regulators are improved and more reliable than the units we've sold previously.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C8AF-10316-A (cover only)

Features the proper cover and original logos. I A S F stamped on cover. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with the 68 A/C Voltage Regulator. Replaces Ford Part #: D0AF-10316-A. The voltage regulators listed in this section are poor quality. We suggest you buy a reliable, modern, solid state unit and just use the cover we sell as a stand alone product. We will not warranty the mechanical voltage regulators you...

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with one for the 68 A/C Voltage Regulator.Replaces Ford part number D0AF-10316-A (cover only)

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Many 70 - 73 cars used 3 pin type switches for the optional automatic seatback release feature. Sold individually. Additionally, this switch for the 3/4 inch mounting hole was used on 1968-70 Full sized Ford such as Custom, 500, Galaxie, LTD, and XL models, full sized Mercury such as Monterey, Montclair, Marquis, and Park...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

There is not a special part number for this angled cup that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1969-70 Mercury Cougar.

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

Tested and inspected neutral safety switch for the C-6 transmission installed in 1970 - early1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D1ZP-7A247-AA, or D0ZZ-7A247-B, SW 920.

Tested and inspected neutral safety switch for the C-6 transmission installed in 69-70 Mercury Cougar and Ford Mustangs. This neutral safety switch is identified by having a single plug, Identified with a single plug with weatherproof seal, the earlier versions do not.Look for a transmission code of U on your door data plate. If your car has a code W, your original transmission was an C-4 and uses a different neutral safety switch.Replaces Ford Part #: C9ZP-7A247. ...

New Old Stock neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

Main wiring harness for consoles on 1970 Mercury Cougar and Ford Mustangs. Short harness more of a jumper wire for the ashtray illumination light. Ashtray wiring socket assembly sold separately.Replaces Ford part # D0ZB-14A012-B.

Reproduction dash to console harness for your 69 - 70 Cougar or Mustang.

D0ZB-13A769-A-AGRADE Right side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-A. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. *Note* Does not include door ajar or factory stereo wiring plugs.

D0ZB-13A769-A Right side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-A. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note* Does not include door ajar or factory stereo wiring plugs. ...

D0ZB-13A769-B-AGRADE Left side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-B. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. *Note* Does not include door ajar or factory stereo wiring plugs.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Good used thermactor smog air...

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.New old stock Ford.

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 1/2/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

D0ZB-13A769-C-AGRADE Right side door wiring harness with decor interior as found on 1970 Standard Cougar (non-XR7's) with door courtesy lights and factory installed stereo. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights and factory door speakers only. Master part number D0ZZ-13A769-C. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

D0ZB-13A769-C Right side door wiring harness with decor interior as found on 1970 Standard Cougar (non-XR7's) with door courtesy lights and factory installed stereo. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights and factory door speakers only. Master part number D0ZZ-13A769-C. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

D0ZB-13A769-D Left side door wiring harness with decor interior as found on 1970 Standard Cougar (non-XR7's) with door courtesy lights and factory installed stereo. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights and factory door speakers only. Master part number D0ZZ-13A769-D. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

Big Block FE 390 or 428 engine feed harness that fits the 1969 or 1970 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C9ZZ-14289-B and D0AZ-14289-A.Check out the video below on our new gauge tester: ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black and yellow boot plugs, this is the style used on cars without air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...