All Available Parts - 1967 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 801-900 of 3109
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 11-9914 -
Air conditioning bearing replacement service. Send your wide bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new wide bearing. Price includes new bearing (long or short shaft) and labor, shipping extra. * Note * There are several pulleys that we are unable to press apart. Please check photos for examples of the known pulleys that we can assemble, but not disassemble. *NOTE* Excludes certain 1968 pulleys with stamped...
Availability: In-Stock Item
Item #: 11-0414 -
Repair your own idler / tensioner with our kit which includes a dust cover and is for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180". We have had a machinist shorten the shaft on these bearings so that they are easily pressed into the cast pulley brackets that use the short...
Availability: Rare / NOS Part
Item #: 33114 -
NOS long shaft bearing for use on all 289, 302, or 390 engines. After 50 years of heat and use, many idler adjusting bearings have seized or are on their way out. This is your answer! This part requires a press to install it. Bearing surface is 1-7/16", bearing diameter is 1.180". Shaft length (sticking out of bearing) 1 1/8" Ford numbers C4AZ-2990-A, C4AA-2A898-A. ...
Availability: In-Stock Item
Item #: 33377 -
New 1-1/4 inch expansion plug. Expansion plugs were used as dust covers on the wide bearing style air conditioning pulleys commonly used on Ford cars 1965-68. These are not a real tight fit in those pulleys. Best to still install to keep dust out, we recommend using a bit of JB Weld to hold them.
Availability: In-Stock Item
Item #: 14306 -
New components used in this harness and not included with main underdash harness. This sub-harness is needed when installing factory in-dash A/C in your Mercury Cougar or Ford Mustang. Even though this picture shows a purple wire, the one that attaches to the back on the starter switch, the part you get will sometimes have a black wire in its place. Keep in mind we also have mint used available. Replaces Ford Part #: C7ZZ-19800-A, tag found on original wires will read C7ZB-19945-A. ...
Availability: Used / Wrecking Yard Item
Item #: 15117 -
Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced after 1/3/1967. This bracket was utilized throughout the entire 1968 model year and is also listed as the service replacement part for the early mounting bracket. Ford part # C7AA-2882-L, MPC # C7AZ-2882-G.
Availability: Used / Wrecking Yard Item
Item #: 15115 -
Used cast iron lateral compressor support bracket for Cougars and Mustangs built after 1/3/1967 and 1968 cars built prior to 3/1/1968, for both the 289 and 302 engine. Must be used with adjusting bracket C7AZ-8678-B pulley assembly, and pedestal bracket C7AA-2882-L.Ford part # C7AA-2888-G or C7AZ-2888-F.
Availability: Used / Wrecking Yard Item
Item #: 15131 -
Cast iron pedestal mount for the air conditioning compressor on all 1967 and 1968 cars with 390-2V, 390-4V, or 428CJ FE engines. Mercury and Ford master part number C7ZZ-2882-A, we suspect that this is an error in our 1975 editions of the MPC's. C7SZ-2882-A is what we suspect is the correct number. In any case, C7SA-2882-A is the factory casting number on these brackets.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird, so there are a few minor...
Availability: Used / Wrecking Yard Item
Item #: 24258 -
Used steel lateral support bracket for 1967 Cougars and Mustangs with the S code 390 engine. Similar to the more commonly found 68-70 bracket but different in multiple ways, most noticeably is the lip on the 1967 "C" shaped area points outward (towards the radiator). Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are...
Availability: Used / Wrecking Yard Item
Item #: 24259 -
1967 Cougar and Mustang tubular steel brace. Connects and supports the rear of the air compressor to the factory intake manifold. From what we can tell there is no difference 67 to 68.Ford part # C7ZZ-2889-A.
Availability: Out of Stock
Item #: 41562 -
C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573.*Note - 3 speed switches are different than the 4 speed switches.
Availability: In-Stock Item
Item #: 42498 -
This reproduction A/C vent register with knobs is show quality and a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs and dealer pricing available.
Availability: In-Stock Item
Item #: 41759 -
New reproduction A/C control knobs for your Mercury Cougar or Ford Mustang / Shelby.
Availability: Used / Wrecking Yard Item
Item #: 11-0317 -
Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. The engineering number imprinted on the back side of this grommet taken from a 1967 Cougar is C7ZA-19B588-A. Good through mid year 1969. Compare to the 1970 item pictured for selection on your late 1969 Cougar.Please indicate in the Order Notes...
Availability: In-Stock Item
Item #: 41949 -
Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A
Availability: Used / Wrecking Yard Item
Item #: 11-0014 -
Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.
Availability: Out of Stock
Item #: 11-0015 -
These were a very poor design and most break where they mount to the bracket. We also have this in the service replacement version with the improved metal housing, very tough part for us to keep in stock. The metal version is a better part and you can get our metal reproduction unit right here!Ford part # C7ZZ-6501891. ...
Availability: Used / Wrecking Yard Item
Item #: 11-0017 -
Under dash bracket used to mount the pull cable for the fresh air vent on the driver side of your Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 14241 -
High Quality cloth wrapped heater duct hose. This is the correct length for most cars, but will need to be cut for proper fit in some applications. Hose diameter: 2 1/2"
Availability: In-Stock Item
Item #: 14245 -
24" hose with metal coil (like original) instead of plastic coil found in most. Coils are wrapped in a 6+ mil plastic rather than the 3 mil plastic that you can easily put your thumb through. Does not come with clips. May require being cut to fit some applications. 2 required per car. Replaces Ford Part #: B5A-18556-C.Replaces Ford Part #: B5A-18556-C.
Availability: In-Stock Item
Item #: 23981 -
Black plastic retainer for attaching the direction air conditioning vent registers.
Availability: In-Stock Item
Item #: 23978 -
Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.
Availability: In-Stock Item
Item #: 23982 -
Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.
Availability: In-Stock Item
Item #: 11289 -
Nice reproduction fresh air vent cable pull assembly. Comes with dash mounted bracket as shown. Much stronger construction than the originals, which were made with a plastic sleeve instead of metal.Replaces Ford part number C7ZZ-6501891-A and C7ZZ-6501891-C.
Availability: In-Stock Item
Item #: 27456 -
All new parts for rebuilding the right and left shutoff butterfly in the air conditioning register vents. Fits all 1967-68 Mercury Cougar and Ford Mustang with factory A/C. Kit includes 2 knobs, 2 black butterfly vent doors, 2 shafts, and 2 retainers. All of these individual parts are also separately. Chrome vent registers and vent retainers are also available.
Availability: In-Stock Item
Item #: 15589 -
Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.
Availability: Used / Wrecking Yard Item
Item #: 11-0090 -
Under dash wiring harness assembly for all 1967 Mercury Cougar and Ford Mustangs with integral, or factory installed air conditioning. All wiring harnesses are test and inspected by our electrical department.Replaces Ford part number C7ZB-19945-A.
Availability: Out of Stock
Item #: 11-0094 -
Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade A version will be free of all but very cosmetic defects. Meaning no broken tabs, or torn or missing screens. Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with heaters only used two individual nozzles.
Availability: Used / Wrecking Yard Item
Item #: 11-0093 -
Defrost or defroster duct for the windshield on all 1967-68 Mercury Cougar and Ford Mustangs with factory A/C or air conditioning. This Grade B version may have one of the following: crack or chip, have a broken tab, or a torn or missing screen. B grades will install and work, they just may need a bit of duct tape or be held on with 3 of the 4 screws.Replaces Ford part numbers C7ZA-18490-E and C8ZA-18490-B.*Note - Only fits those cars with factory or integral air conditioning. Cars with...
Availability: Used / Wrecking Yard Item
Item #: 11-0108 -
Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...
Availability: In-Stock Item
Item #: 10120 -
Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.
Availability: Used / Wrecking Yard Item
Item #: 11-0131 -
Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, switch, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door. Stapled foam seal to center vent may not be perfect.Replaces Ford part number C7ZA-19740-B.
Availability: Out of Stock
Item #: 11-0293 -
Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.
Availability: Out of Stock
Item #: 11-0356 -
Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...
Availability: Out of Stock
Item #: 30613 -
Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Nice fit, made of plastic. Will work with or without console, has slightly wider wings for clearance of the rear of the factory installed consoles.
Availability: In-Stock Item
Item #: 30614 -
Reproduction A/C floor duct for 67 - 68 Cougars and Mustangs without a console.
Availability: Out of Stock
Item #: 11-0405 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade A vents will not have any cracks or breaks.
Availability: Used / Wrecking Yard Item
Item #: 11-0406 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.
Availability: Used / Wrecking Yard Item
Item #: 11-0407 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade A vents will not have any cracks or breaks.
Availability: Used / Wrecking Yard Item
Item #: 11-0408 -
Used A/C floor duct for 67 - 68 Cougars and Mustangs without a console. Grade B vents will have a small crack or break usually around the mounting holes, but will not effect it's functionality.
Availability: In-Stock Item
Item #: 11-0410 -
Vacuum switch that attaches to the air conditioning lever assembly on all 1967-68 Mercury Cougar and Ford Mustangs with integral A/C.Ford number stamped C7ZA-19B919.
Availability: Used / Wrecking Yard Item
Item #: 11-0018 -
This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade A hose that is not cracked, may have a small cosmetic scuff in the foam, and the clips will not be broken. Two required per car, sold individually. We also have a listing for Grade B condition, that will have a minor issue or two. Ford part #: C7WY-19B680 or B5A-18556-C.
Availability: Out of Stock
Item #: 41779 -
Both ends have 90 degree molded ends. Attaches heater core to water heater control valve.Replaces Ford Part #: C7ZZ-18472-CVAC.
Availability: In-Stock Item
Item #: 41915 -
Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.
Availability: In-Stock Item
Item #: 41924 -
Concours correct and constructed in original Ford style black thermoplastic material with a nylon barrier. This hose assembly is built to be compliant for R-12 or 134a refrigerants.NOTE: We have three hoses from a previous supplier that we have available for about half the price. The only difference would be that instead of the thermoplastic material, these are the standard rubber type hoses. Pick one up here. ...
Availability: In-Stock Item
Item #: 41940 -
Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.
Availability: In-Stock Item
Item #: 41774 -
Senses temperature to open and close the expansion chamber and made just like the original.Will work with both R12 and R134 systems.Replaces part #: C7ZZ-19849.
Availability: In-Stock Item
Item #: 42066 -
These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B
Availability: In-Stock Item
Item #: 42068 -
These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S
Availability: In-Stock Item
Item #: 42067 -
These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C
Availability: In-Stock Item
Item #: 13999 -
This valve is used on Mercury Cougars and Ford Mustangs equipped with factory A/C to stop the flow of warm coolant when A/C is on.This valve is functionally the same as the OEM, but has obvious cosmetic differences from the factory valve.Replaces Ford Part #: C7ZZ-18495-A.
Availability: In-Stock Item
Item #: 41890 -
This is used on Mercury Cougars and Ford Mustangs equipped with factory A/C. This is the bracket for the valve that stops the flow of warm coolant when A/C is turned on. This is an exact reproduction and has the zinc dichromate finish.
Availability: Ships Direct from Supplier (Except International)
Item #: 42069 -
This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.
Availability: In-Stock Item
Item #: 41793 -
Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.
Availability: In-Stock Item
Item #: 41792 -
These are correct reproductions of the A/C discharge service valve that comes with plastic caps. if you would like the correct aluminum valves, we sell those separately.
Availability: In-Stock Item
Item #: 41358 -
No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually.
Replaces Ford part #: C7ZA-430.
Availability: Used / Wrecking Yard Item
Item #: 11-0003 -
Mounts to the rear of the factory installed air conditioning ventilation control panel on Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1967 selector button kit.Ford part # C7ZZ-19986-A.
Availability: In-Stock Item
Item #: 41507 -
This reproduction heater blower switch for Mercury Cougar and Ford Mustang mounts to the rear of the factory installed air conditioning ventilation control panel.Replaces part # C7ZZ-19986-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0006 -
We offer this "Core Grade" assembly for those that purchase the various 1967 reproduction air conditioning bezels. This assembly will provide the needed 'guts' for behind the various 1967 Mercury Cougar or Ford Mustang A/C and heater control bezel. A Complete A/C heater control assembly includes bezel or face plate(bezel will be pitted and possibly broken), bracket control mounting plate, electrical and vacuum switches, and hardware. *NOTE* - Does not include knobs or cable.Ford part #...
Availability: Out of Stock
Item #: 11758 -
Reproduction set of A/C register connectors for Mercury Cougars and Ford Mustangs with integral A/C. These mount directly behind the round dash vents and work well with both the original vents or our high quality reproduction vents.
Availability: Used / Wrecking Yard Item
Item #: 11-0008 -
Work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0009 -
Passenger side A/C duct register, or elbow, connector for Mercury Cougars and Ford Mustangs equipped with integral or factory A/C. These elbows work perfectly with our reproduction A/C registers.Ford part # C7ZZ-19C692-B.
Availability: Out of Stock, On Order
Item #: 32345 -
Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang.
Availability: Out of Stock, On Order
Item #: 32348 -
Reproduction black center A/C vent for the 67 - 68 Mustang.
Availability: Out of Stock, On Order
Item #: 32346 -
Reproduction driver side A/C vent with black camera case finish for the 67 Mustang.
Availability: Used / Wrecking Yard Item
Item #: 11-0233 -
Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. We also offer another valve that was used for a period of time see the related evaporator valve.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service. This valve was originally stickered with a FoMoCo tag and...
Availability: Used / Wrecking Yard Item
Item #: 24207 -
Regardless of which V-8 engine, C7ZA-19835-A or C7ZA-19837-D both can be the correct part number. This hose is approximately 74 inches long and this line also incorporates the site glass. The Ford MPC # is C7OZ-19837-A.
Availability: Used / Wrecking Yard Item
Item #: 24208 -
Regardless of which V-8 engine, C7ZA-19867-C is the correct part number. This hose is approximately 55 inches long.Ford MPC part # C7ZA-19867-C.
Availability: In-Stock Item
Item #: 26155 -
Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang with factory or integral A/C. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. The 'with air conditioning' hoses have correctly molded 90 degree elbows that fit on the water valve side. Some length trimming may be needed for a tight looking fit.
Availability: In-Stock Item
Item #: 10905 -
New A/C vent hose with cam locks for your Mercury Cougar or Ford Mustang equipped with factory A/C. This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Two required per car, sold as a pair.Ford part #: C7WY-19B680 or B5A-18556-C.
Availability: In-Stock Item
Item #: 11087 -
Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.
Availability: Out of Stock
Item #: 10197 -
Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.
Availability: Used / Wrecking Yard Item
Item #: 11940 -
Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.
Availability: In-Stock Item
Item #: 31283 -
New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.
Availability: Out of Stock
Item #: 12346 -
Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.
Availability: Used / Wrecking Yard Item
Item #: 11941 -
Steel elbow that uses the A/C coupler from the liquid or sight glass hose to the dryer. This is an OEM Ford part that was originally part of an assembly, which included the sight glass hose, coupler, and this elbow. This elbow has the flared fitting common to the 1967-68 A/C connections. We recommend replacing "O" rings prior to installation, which are commercially available from air conditioning service centers.
Availability: Used / Wrecking Yard Item
Item #: 11-0234 -
Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. This is the uncommon version, we have a limited supply of these from original cars.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C6OZ-19849-A. aka YG-24
Availability: Used / Wrecking Yard Item
Item #: 11-0095 -
This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade B hose that may have a crack or tear, or with a broken clip. Two required per car, sold individually. We also have a listing for Grade A hoses. Ford part #: C7WY-19B680 or B5A-18556-C.
Availability: Ships Direct from Supplier (Except International)
Item #: 10005 -
Fits 1967 Cougar and Mustang with factory Heater Only Firewall and 1967 289 engine. Custom Hurricane Heat Cool & Defrost System for 1967-68 Mercury Cougar / Ford Mustang with original 289 V-8 with or w/o Power Steering. Easy to Install! Hurricane Unit mounts to firewall in place of factory heater, a/c & heater fittings pass neatly through original blower motor hole with custom rubber grommet. Electronic switching package includes correct reproduction A/C Control bezel w/ louvers. Electronic...
Availability: Used / Wrecking Yard Item
Item #: 11907 -
Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang. This spacer also fits many other Ford applications. Ford part number: C5AZ-10A344-B.
Availability: Used / Wrecking Yard Item
Item #: 23841 -
Used stamped steel single groove alternator pulley, typically these are described as being 2-7/8 inches in diameter. We find various casting numbers on them, such as: C5AF-10A352-F1, C5AF-10A352-G1, C5AF-10A352-K, C5AF-10A352-L.Replaces Ford part number C5AZ-10344-K.
Availability: In-Stock Item
Item #: 11303 -
This is a 'made in China' wiring harness. Quality is OK and will work for this application. Application is 1967-68 Mercury Cougar XR7 models and Ford Mustang without factory tachometer option, all with 289 or 302 engines. *Caution, not for use with Cougar standard models or Mustang with alternator warning light. *Note - Excludes California models or cars with factory Thermactor smog pump with low mounted alternators.Replaces Ford Part # C7ZZ-14305-B Door Tag 65B
Availability: In-Stock Item
Item #: 11635 -
Reproduction alternator wiring harness for all 1967 Mercury Cougar Standard Models, meaning Non XR7. Additionally 1967 Ford Mustang with tachometer. Excellent reproduction copied from an NOS wiring harness.Ford service number C7ZZ-14305-E, wire harness marked C7ZB-14305-E.
Availability: In-Stock Item
Item #: 11634 -
Nice reproduction of the original alternator wiring harness, has individual colored boots and wire colors match up to the original Ford drawings. Application is 1967 Mercury Cougar standard models or 1967 Ford Mustang with factory tachometer option, all with S code 390-4V engines. Ford service part number C7ZZ-14305-D, original harness numbered C7ZB-14305-D. *Caution, not for use with Cougar XR7 models or Mustang with ammeter gauge. *Note - Excludes California models with Thermactor smog pump...
Availability: In-Stock Item
Item #: 11633 -
Nice reproduction of the original alternator wiring harness, has individual colored boots and wire colors match up to the original Ford drawings. Application is 1967 Mercury Cougar XR7 models or 1967 Ford Mustang with factory tachometer option, all with 390-4V engines. Ford service number C7ZZ-14305-C, original wire harness marked C7ZB-14305-C. *Caution, not for use with Cougar standard models or Mustang with alternator warning light.*Note - Excludes California models or cars with factory...
Availability: Restored / Remanufactured
Item #: 11-9912 -
Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...
Availability: Out of Stock
Item #: 24993 -
Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 24338 -
Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.
Availability: Used / Wrecking Yard Item
Item #: 24339 -
Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.
Availability: Used / Wrecking Yard Item
Item #: 23859 -
Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.
Availability: Out of Stock
Item #: 23839 -
Fan spacer, measuring 3-1/16 inches, sometimes mentioned as 3.40" overall. Applications include 1967 Mercury Cougar and Ford Mustang with 289-4V. Reference number YA-78.Ford part # C5AE-8546-B, Ford engineering # C5AZ-8546-B.
Availability: In-Stock Item
Item #: 10895 -
Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 23851 -
Ford part number C5AZ-6312-B. Application for 1967-68 289 and 302 engines without all of the following; air conditioning, power steering, California thermactor smog. The alternator would also have a single sheave pulley. Ford casting number C5AE-6312-A. Single sheave crank shaft pulley. About 6-5/16 inches in diameter.
Availability: Used / Wrecking Yard Item
Item #: 23852 -
C5AZ-6312-D Application for 1967-68 289 or 302 engines with air conditioning. Power steering and or California Thermactor emissions permissible. Ford casting number C5AE-B. Triple sheave 67 68 crank pulley. Inner diameters are about 6-1/2 inches, outer diameter is 7-5/16 inches.
Availability: Used / Wrecking Yard Item
Item #: 23853 -
C5AZ-6312-E Application 289 engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions. 6 5/16" wide 3" deep to mounts. Ford casting number C7AE-6312-A. Double sheave 67 crank pulley.
Availability: Used / Wrecking Yard Item
Item #: 23917 -
C6AZ-6A312-A Two applications on 289 engines. 1. Manual transmissions and standard cooling (standard cooling is the 17 inch radiator). 2. All transmissions with extra cooling (extra cooling is the 20 inch radiator). Dual belt alternator pulley, California emissions permissible. & Without air conditioning or power steering. Ford casting number C6OE-6312-A. Double sheave 67 crank pulley. 6-5/8 inches in diameter.
Availability: Used / Wrecking Yard Item
Item #: 24018 -
C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...
Availability: Used / Wrecking Yard Item
Item #: 31809 -
New crank shaft pulley with 2 sheaves for any 3 bolt, 289 / 302 / 351W engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions. 6-3/8" overall diameter, has 3/8 and 1/2 inch grooves for fan belts. Replica of the C7AE-6312-A crankshaft pulley by Ford. Double sheave 67 crank pulley.
Availability: In-Stock Item
Item #: 15110 -
Ford casting number C4AE-6316-A. All 1967 S code 390-4V engines. 1967 only, 6-5/8 inches in diameter, cast iron construction with key way groove. This is a combination crankshaft balancer and pulley. Has the timing marks on rim. Ford Master Part number C3AZ-6312-E. Refundable $80.00 core charge when rebuildable C4AE-6316-A harmonic balancer is received by WCCC.*Note - This harmonic balancer is generally covered up by an outer crankshaft pulley when options such as air conditioning and power...
Availability: Used / Wrecking Yard Item
Item #: 23864 -
Ford casting number C5TE-6312-A. Single cast iron pulley for use with California thermactor emissions and low mount dual alternator pulleys. No other options, just the DSO 52 and 53 California engines. Ford Master Part number C5TZ-6A312-A. 6-5/8 inches in diameter.
Together with the inner crankshaft balancer pulley, these now paired pulleys drive both the water pump and alternator pulleys. The Thermactor air pump pulley is driven by the 3rd outer water pump pulley sheave - only. Must use the...