All Available Parts - 1967 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 601-700 of 3156
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 10117 -
This is the stainless steel, single prong version fuel sending unit for 67 - 68 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. *Note - This...
Availability: In-Stock Item
Item #: 18898 -
Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1967 - 1968 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1968 fuel sending unit with three prongs (2 electrical and 1 alignment prong). The original Ford casting number was C8ZF-9275-B, master parts catalog number C8ZZ-9275-D. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely...
Availability: Out of Stock
Item #: 30371 -
This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...
Availability: In-Stock Item
Item #: 30513 -
Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...
Availability: In-Stock Item
Item #: 31210 -
This is a single plug (standard models without low fuel warning light) fuel sending unit with an extra bung for a return line for 1967-68 Cougars and Mustangs running fuel injection. No need to change the whole tank in order to upgrade your car to fuel injection! Main line 3/8" Return line 1/4" Check out the video below on our new gauge tester: ...
Availability: Ships Direct from Supplier (Except International)
Item #: 32191 -
This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...
Availability: In-Stock Item
Item #: 32404 -
This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Be aware that the OEM Ford 1967 sending units had 5/16 inch tubes for the filter, 1968 had 3/8 inch tubes.Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980...
Availability: In-Stock Item
Item #: 32439 -
Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.
Availability: In-Stock Item
Item #: 15999 -
Reproduction heater dash plate for the 67 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).Replaces Ford part number C7ZZ-18A651-B
Availability: In-Stock Item
Item #: 26062 -
Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand.Here is a helpful youtube video on how to go about removing a headlight...
Availability: In-Stock Item
Item #: 26128 -
Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang.
Availability: In-Stock Item
Item #: 26127 -
Quality reproduction to replace your pitted original. Replaces Ford Part #: C7ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang.
Availability: In-Stock Item
Item #: 14259 -
Inexpensive upgrade, replaces that bezel damaged by improper screw driver removal. We also sell the special tool that removes this without hassle or damage
Availability: Used / Wrecking Yard Item
Item #: 23425 -
This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.
Availability: Used / Wrecking Yard Item
Item #: 10669 -
Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.
Availability: Used / Wrecking Yard Item
Item #: 23233 -
Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly.
Availability: Used / Wrecking Yard Item
Item #: 13134 -
Used ignition lock cylinder bezel for any 1967-68 Mercury Cougar, ford Mustang and likely Fairlane / Comet. Good used condition, we recycle the pitted crusty ones. Half the price of the repop version. We also sell the special tool that removes this without hassle or damage.Replaces Ford part number C6OZ-11584-A.
Availability: Used / Wrecking Yard Item
Item #: 21-1018 -
This is the longer of the two versions found on the 1967 XR7 and also found on the Shelby and Mustang. The lens used with this reset button has a smaller hole than the 1968 version.
Availability: In-Stock Item
Item #: 12976 -
Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.
Availability: In-Stock Item
Item #: 32669 -
Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.
Availability: In-Stock Item
Item #: 41945 -
Fits either 1967 or 1968 Mercury Cougar or Ford Mustang. Technically this is a copy of the 1967 factory installed version. 1968 factory glove box liners have a smooth section for installing the tire pressure decal. See the related items for 1967 and 1968 good used liners. Replaces Ford part #: C7ZZ-6506010-A.
Availability: Used / Wrecking Yard Item
Item #: 17778 -
Used glove box liner or plastic box for any 1967 Mercury Cougar or Ford Mustang. This is the same as the Scott Drake reproduction, but it lacks the smooth section for the tire pressure decal which was introduced on the 1968 cars. Used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange, Replaces Ford part number C7ZB-6506010-A.
Availability: In-Stock Item
Item #: 41524 -
A great optional accessory. All new tooling was created to produce these glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Replace Ford Part #: C6DZ-6506072.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges.
Availability: In-Stock Item
Item #: 10650 -
Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.
Availability: In-Stock Item
Item #: 10615 -
Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang
Availability: Used / Wrecking Yard Item
Item #: 27284 -
Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang
Availability: In-Stock Item
Item #: 27593 -
New improved set of 6 screw for the glove compartment hinge on all 1967-68 Mercury Cougar and Ford Mustangs. Three 10-24 bolts with 0.72" conical washer heads to go into dash, and three 10-24 bolts with 0.50" conical washer heads to attach to glove box door. This is an updated proper kit for 1967-68 Mercury Cougar and Ford Mustang glove box door hinge. All AMK bolts, but WCCC special recipe. 6 pieces as shown.
Availability: Used / Wrecking Yard Item
Item #: 18936 -
Used glove box liner or plastic box for any 1968 Mercury Cougar or Ford Mustang these do have the flat smooth area for installing the tire pressure decal. This is nearly the same as the 1967 used and Scott Drake reproduction, which lack the smooth section for the tire pressure decal. Good used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange.Replaces Ford part number C8ZB-6506010-A.
Availability: Used / Wrecking Yard Item
Item #: 12962 -
Used hinge for any early 1967 Mercury Cougar or Ford Mustang. This early hinge is flat, the later 1967 and 1968 hinge had two ribs formed for added strength. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-A.
Availability: Used / Wrecking Yard Item
Item #: 16199 -
Used hinge for any 1967-68 Mercury Cougar or Ford Mustang. This hinge has two ribs formed for added strength. There was an early 1967 version of this hinge that did not have the ribbing. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-B.
Availability: In-Stock Item
Item #: 12995 -
Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0160 -
A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. See related for reproduction and 1967 used.
Availability: Used / Wrecking Yard Item
Item #: 11-0357 -
A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1967, notice the push button with square edge? 1968 push buttons had rounded edges. See related for reproduction and 1968 used.
Availability: Used / Wrecking Yard Item
Item #: 31274 -
Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang
Availability: Out of Stock
Item #: 26514 -
These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...
Availability: In-Stock Item
Item #: 14514 -
Reproduction front armrest in turquoise for the Mercury Cougar. This unit is ambidextrous, meaning it will fit either the driver (left hand) or passenger (right hand) sides. Although many vendors would disagree, these are in my opinion average quality. "BUT" they are the best available reproductions on the market at this time. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. Left and right are the same for 1967 standard...
Availability: In-Stock Item
Item #: 27498 -
New screw with a correct 3/8 inch hex head for installing all armrests for all years.
Availability: In-Stock Item
Item #: 14034 -
These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair.Replaces Ford Part # C8ZZ-6526656. *Customer Feedback* Don and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy...
Availability: In-Stock Item
Item #: 42043 -
These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair Replaces Ford part # C8ZZ-6526656.
Availability: In-Stock Item
Item #: 26211 -
Plastic injection molded, chrome plated just like the originals. Sold as a pair. Replaces Ford part number C5DZ-6221850-A
Availability: In-Stock Item
Item #: 10099 -
Reproduction medium blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed.*NOTE* There are two types of this trim found in the 1967-68, the smooth or rough texture. ...
Availability: In-Stock Item
Item #: 13888 -
The same plastic lock rod grommet but with a nice chrome finish for an extra touch. Sold in pairs. Replaces Ford Part #: C5DZ-6221999-B or C5DZ-6221999-C.
Availability: In-Stock Item
Item #: 18983 -
Good Reproduction of the clear plastic door lock grommets. Sold as a pair. Replaces Ford Part #: C5DZ-6221999-B.
Featured!
Availability: In-Stock Item
Item #: 13-0003 -
New, more accurate woodgrain as of 2019! These decals are cut to fit the 1967 door pull end caps. The 1968 end caps had a smaller woodgrain insert with a black border. We also sell a slightly smaller version of this kit for the 1968 owners. This kit also fits the reproduction end cap kit. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...
Availability: In-Stock Item
Item #: 33106 -
Plastic injection molded, chrome plated just like the originals. Sold as a pair. Replaces Ford part number C5DZ-6221850-A
Availability: In-Stock Item
Item #: 11959 -
Reproduction dark blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Availability: In-Stock Item
Item #: 11961 -
Reproduction dark red rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Availability: In-Stock Item
Item #: 11963 -
Reproduction light blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Availability: Out of Stock
Item #: 11967 -
Reproduction saddle rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Availability: In-Stock Item
Item #: 11969 -
Reproduction white rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Availability: In-Stock Item
Item #: 11971 -
Reproduction aqua rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Availability: In-Stock Item
Item #: 30936 -
Reproduction black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...
Featured!
Availability: In-Stock Item
Item #: 26756 -
This is a reproduction steering wheel for a 1967 Mustang with Deluxe interior. It makes a nice substitution for the 1967 Mercury Cougar wheel and since the 1967 Mustang used the same steering columns (both fixed and adjustable) you are guaranteed a factory correct fit with no issues making your horn or turn signal cancellation work properly. This steering wheel is being offered without a horn center / pad. You can use your original Cougar hub, which fits perfectly without modification. If you...
Availability: In-Stock Item
Item #: 26191 -
Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...
Availability: In-Stock Item
Item #: 31094 -
Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.
Availability: Used / Wrecking Yard Item
Item #: 19259 -
Good used light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow. Ford Part Number: C7ZZ-15A808B Fits 67 CougarFits 67 Mustang Check out our video on rebuilding...
Availability: Used / Wrecking Yard Item
Item #: 24215 -
Pit free original rear console courtesy light for all consoles 67-68, does not usually come with a good lens as most are cracked, faded or missing. Casting number as seen on the back reads C7ZB-13743-A. Number imprinted on wire can be: C4VB-13757-A.
Availability: In-Stock Item
Item #: 14376 -
Map light bezel for overhead roof consoles on both 1967-68 Mercury Cougar XR7 and Ford Mustang. These are a great reproduction at a great price. These were always pitted and before the reproductions came out three years ago a very nice used pair sold for about $100. To date we have sold more than 300 pairs and have had great feedback! Sold in pairs. Bezels only. Sometimes called a 'door' Ford part number C7ZZ-13788-A. *Customer Comments* Hello. I just bought my first 1967 Cougar XR7 in about...
Availability: In-Stock Item
Item #: 18741 -
Reproduction light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). The 1967 light had a male / female black combination plug. If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow. Ford Part Number: C7ZZ-15A808B Check out...
Availability: In-Stock Item
Item #: 15537 -
The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...
Availability: In-Stock Item
Item #: 25951 -
Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages.
Availability: In-Stock Item
Item #: 15538 -
This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...
Availability: In-Stock Item
Item #: 25952 -
Manual on how to modify your FE big block Ford for street or strip.
Availability: In-Stock Item
Item #: 25950 -
Complete engine modification specifications manual for 1960 through early 1970 Ford engines. Includes everything from the 98 CID 4 cylinder to the 460.
Availability: In-Stock Item
Item #: 25949 -
Reproduction BOSS 302 Chassis Modification for the Strip Track Manual. This little book is packed full of tips and tricks to make your Cat or Pony and handling MACHINE! The tips in the manual also apply to the 1967-68 Cougar or Mustang. Time to sharpen the claws on your flexxy feline!
Availability: In-Stock Item
Item #: 25955 -
Complete reprint of the 1967 Vacuum Schematic for the Mustang. If you would like we can include a copy of the Vacuum Schematic for the Cougar Vacuum Headlight System from the Ford Master Parts Catalog. This is for Mustang so it will not show the Cougar but will work for the vacuum system. Mustang and Cougar were the same with the exception of the headlights.
Availability: In-Stock Item
Item #: 42086 -
Complete reprint of the 1967 Vacuum Schematic for the Mustang. If you would like we can include a copy of the Vacuum Schematic for the Cougar Vacuum Headlight System from the Ford Master Parts Catalog.
Availability: In-Stock Item
Item #: 32673 -
This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...
Availability: In-Stock Item
Item #: 33033 -
This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...
Availability: In-Stock Item
Item #: 14060 -
These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A
Availability: In-Stock Item
Item #: 31982 -
AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.
Availability: Used / Wrecking Yard Item
Item #: 11068 -
Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...
Availability: Out of Stock
Item #: 14035 -
This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969.
Availability: In-Stock Item
Item #: 11795 -
Installation of this bracket is easy but you will have to make a spacer to fit on the outside of the frame rail. Hopefully you bought this bracket first before you tore out the nut inserts in the frame. If not you will need to get them up for now. Then tap the bracket toward the the outside of the car and make sure the cross bolt lines up. Then measure the gap and make a spacer to fit. A half inch nut and a couple of washers usually work just fine. It's not necessary to get fancy with this...
Availability: Used / Wrecking Yard Item
Item #: 24214 -
This cast bracket bolts to the frame on the driver side and anchors the power steering hydraulic cylinder. One of the benefits of buying parts from Western parts cars is that they have not been corroded by salt! This part comes "as taken from a parts car". At least two variations of this bracket (see photos above) between 1967-70. Our observations show the version with the curved casting number version orientation to be from 1970 Cougars with were all built in Dearborn, Michigan. The...
Availability: Out of Stock
Item #: 13794 -
Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.
Availability: In-Stock Item
Item #: 10735 -
Nut for attaching the power steering pump bracket onto the pivot stud coming out of the cylinder head. All 1967-69 Mercury Cougar and Ford Mustang engines additionally used on 1970 428CJ engines.
Availability: In-Stock Item
Item #: 11784 -
Reproduction power steering drop bracket for the Mercury Cougar or Ford Mustang. One must use this part when installing headers with power steering. Because of the way this bracket hangs down, it will get bumped and bumped hard in time. Becasue of this we recommend considerning our premuim version of this bracket, as it is substantially stronger.
Availability: Used / Wrecking Yard Item
Item #: 31880 -
This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.
Availability: Used / Wrecking Yard Item
Item #: 31881 -
This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.
Availability: In-Stock Item
Item #: 42009 -
Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.
Availability: Used / Wrecking Yard Item
Item #: 30267 -
Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.
Availability: In-Stock Item
Item #: 31811 -
Application could be for any 1967-69 Ford 289 / 302 /351W, but with only a single alternator belt. This is a copy of the Ford 7AA power steering pulley. This pulley mounted correctly on an OEM pump with factory brackets, will run on the second V-belt from the inside. The inner most fan belt runs the alternator. You would be using a single belt on the alternator. Correct application is for 1969 with 351W engines. 5-1/4" diameter and 3/8" sheave width.
Availability: Used / Wrecking Yard Item
Item #: 24067 -
C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to...
Availability: Used / Wrecking Yard Item
Item #: 20669 -
Grade B Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps....
Availability: Used / Wrecking Yard Item
Item #: 33480 -
Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...
Availability: Used / Wrecking Yard Item
Item #: 33481 -
C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have...
Availability: Out of Stock
Item #: 25658 -
Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.
Availability: In-Stock Item
Item #: 33479 -
Bolt kit for mounting power steering ram cylinder brackets to the frame rail on any 1967-70 Mercury Cougar or Ford Mustang. Kit includes: two short bolts with lock washers, long horizontal bolt, nut, and reinforcing washer. Quality AMK fastener kit.
Availability: Out of Stock
Item #: 26188 -
Mounts onto the transmission. Fits all 1967 - 1968 8 Cylinder.
Availability: In-Stock Item
Item #: 13816 -
Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.
Availability: In-Stock Item
Item #: 14377 -
Quality part for your C-4 but will work on the C-6 67-68 transmission. Measures 10.2" long. Replaces Ford Part #: C6OZ-7A187-D.
Availability: In-Stock Item
Item #: 11309 -
C4 Automatic transmission kick down cable kit for all 1967-68 Mercury Cougar and 1966-68 Ford Mustangs. Kit includes kick down cable assembly, accelerator kick down lever, retracting spring, and related hardware.
Availability: Used / Wrecking Yard Item
Item #: 16-0019 -
Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...
Availability: Used / Wrecking Yard Item
Item #: 16-0072 -
First generation Cougars 1967 and 1968, used a single bracket for C4 automatics and both 3 speed and 4 speed manual transmissions. This bracket also carried over to 1969 and 1970 with 351 or Boss 302 engines and either 3 or 4 speed manual transmissions. Ford part number C7ZZ-6A023-D. This part weighs 2.28 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 1/4" on center and the passenger side 2 3/4" on center.The reproduction Dynacorn part...
Availability: Ships Direct from Supplier (Except International)
Item #: 19949 -
New crossmember to adapt the Tremec TKO manual transmission to the Mercury Cougar or Ford Mustang. This unit can also be used for the Ford AOD.
Availability: Ships Direct from Supplier (Except International)
Item #: 30096 -
Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.
Availability: Used / Wrecking Yard Item
Item #: 30097 -
Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.
Availability: Used / Wrecking Yard Item
Item #: 16-0051 -
Dust and safety plate for all C4 (code W) automatic transmissions also known as the Cruis-o-Matic transmission. Inspection cover for torque converter and flexplate.
Availability: Used / Wrecking Yard Item
Item #: 16-0052 -
Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....