All Available Parts - 1967 Ford Mustang

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission. Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift Linkage This is just the kit, and does not include the full transmission!

Reproduction flexplate reinforcing ring. Strengthens the area where the automatic transmission flexplate mounts to the crankshaft. 5.12" outside diameter3.34" inside diameter .060 inches thickFits: 352 390 427 428 429 460 with C6 and FMX transmissions.Replaces Ford part # B9AZ-6A6366-B

Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...

Core C-6 Transmission valve body for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with code "U" transmission code on the door tag. This is only for 1967 through 1968 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Bracket tack welded in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang. These are sold individually, these are not side specific. There is also a reproduction version available. Used part cut from a 1967-68 Mercury Cougar, some spot welds will need to be drilled out on your end. Picture shows approximately what you will receive. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang.Sold as a pair and are not side specific. 

This is the modern version of the Kelsey Hayes wheels that were originally equipped on 1967 Shelbys. One-piece cast aluminum structure with a CNC machined face and durable clear coat finish. The lighter weight one piece design also provides a significant weight savings over the original steel design, delivering improved acceleration and braking performance. These take specific lug nuts and center caps (sold separately, see related items). These wheels come with free chromed plastic center...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...

Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with natural aluminum accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

These T/A style wheels have the classic 8-spoke European design that was popular with road racers in the 60's and 70's. Fits the 60-73 Mustang, Falcon, Fairlane, Comet and 67 - 70 Cougar. Chrome plated plastic Legendary Wheel hubcap included. Back spacing on all Legendary wheels is 4 1/4". Bolt pattern 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. Check out our video on Legendary Wheels below: ...

Nice original snorkel that is correct for 2V and 4V 289 motors both 49 state and California Cougars. Due to the age of these parts, the internal thermal mechanism can be presumed to not work. Ford part number C7ZF-9A626-A.

Reproduction wing nut for the snorkel on your air cleaner. Good for the 1967 Cougar or Mustang.

Correct for all 1967 Cougars with a 289. Keep in mind the Cougar never came factory with a 289 HiPo.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs to be of lesser quality than the originals, and they will stretch over time and not hold the hood up very well. We highly recommend you stick with original OEM springs. No returns on these springs. Click here to see our listing for good used originals. Replaces Ford part # C3OZ-16789-A. You can...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Bolts to the cowl on 1967-68 Mercury Cougar and Ford Mustang. Ford part number C7ZB-16A006-A passenger side, C7ZB-16A005-A driver side.

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side lower only, kind of shaped like the State of Utah. Fits driver and passenger side hinges. Fits any 1967 Mercury Cougar and Ford Mustang. Ford part number 6502667.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side upper only. Fits any 1967 Mercury Cougar and Ford Mustang.Ford part number 6502666.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Reproduction GT style concours correct air cleaner assembly with a chrome lid and California emissions tube for all Mercury Cougars and Ford Mustangs equipped with the 390GT engine. This is an extremely hard piece to find used and even rarer in NOS form. Now we can offer you this new unit that is made from the original tooling! This reproduction includes a blue base, a chrome lid, and a lid to base rubber gasket. This is also an excellent stock appearing performance upgrade for the very...

Reproduction 1967 GT concours correct air cleaner assembly with the chrome lid for the Mercury Cougar and Ford Mustang equipped with the 390 engine. Notice that this version does not have the metal elbow on the side for the hose going to the oil fill cap? This is an extremely hard piece to find used and even rarer in NOS form. Now we can offer you this new unit that is made from the original tooling! This reproduction includes a blue base, a chrome lid, and a lid to base rubber gasket. Some...

Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

Complete floor pan for the 1965-68 Ford Mustang. NOTE: Can be made to fit 67-78 Cougar, Included seat risers are Mustang versions, which are taller than the Cougar seat risers. We recommend re-using your original Cougar seat risers, unless you want the extra height of the Mustang risers. Also note that the risers included with this floor pan will not be attached, you'll have to weld them on. Keep in mind Cougar has a longer wheel base which make the portion under the back seat substantially...

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

This piece runs under the floor over the transmission where the floor pan meets the firewall.

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

New inner floor frame support for the Mercury Cougar and Ford Mustang.

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

If you are buying our one piece Mustang floor pan or our driver side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

If you are buying our one piece Mustang floor pan or our passenger side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.

These reproduction J clips mount to the underside of the deck lid and fit Standard and XR7 trunk lids.

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

These reproduction hood latch catch bolts fit both the Standard and XR7.

These reproduction fender to pillar bracket bolts fit both the Standard and XR7.

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

These reproduction fender shield to bumper screws fit bot the standard and XR7.

Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Reproduction "A" pillar repair panels for your 67 - 68 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Get ready for some serious labor if your car needs this complete panel!

Reproduction driver side front inner apron for both the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side front fender apron that has the shelf for installing the battery tray. *Restoration Hint* This section of metal was VIN stamped, consider welding in the stamped VIN section to keep your car whole.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

Solid, undamaged driver and passenger side shock tower braces. Fits all 1967-68 Mercury Cougar and Ford Mustang. Ford part #s C5ZZ-16A053-B driver side (left hand) and C5ZZ-16A052-C passenger side (right hand). *NOTE* Excludes 1967-68 Mustang Convertible. **Installation Tip** These brackets attach under the cowl lip. ...

Used driver side (left hand) shock tower brace for the Mercury Cougar and most Ford Mustangs. Solid, undamaged brace. Consider our brace kits - best value. Ford part # C5ZZ-16A053-B.*NOTE* Excludes 1967-68 Mustang Convertible.