All Available Parts - 1967 Ford Mustang

Regardless of which V-8 engine, C7ZA-19835-A or C7ZA-19837-D both can be the correct part number. This hose is approximately 74 inches long and this line also incorporates the site glass. The Ford MPC # is C7OZ-19837-A.

Regardless of which V-8 engine, C7ZA-19867-C is the correct part number. This hose is approximately 55 inches long.Ford MPC part # C7ZA-19867-C.

Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang with factory or integral A/C. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. The 'with air conditioning' hoses have correctly molded 90 degree elbows that fit on the water valve side. Some length trimming may be needed for a tight looking fit.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1967-68 Mercury Cougar and Mustang, 1966-69 Lincoln Continental, 1966-67 Mercury Cyclone and Ford Fairlane/Ranchero. This is the uncommon version, we have a limited supply of these from original cars.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C6OZ-19849-A. aka YG-24

This hose is unique to vehicles equipped with A/C and is 25 1/4" long with a diameter of 2 1/2". It has a metal coil surrounded by 3/32" of foam rubber with factory clips on each end. Grade B hose that may have a crack or tear, or with a broken clip. Two required per car, sold individually. We also have a listing for Grade A hoses. Ford part #: C7WY-19B680 or B5A-18556-C.

Exact replacement for your original dryer and should be changed anytime the system is recharged. This stainless steel filter element is the life of your system and stops contaminants from clogging the expansion valve. Painted the correct satin black.

Fits 1967 Cougar and Mustang with factory Heater Only Firewall and 1967 289 engine. Custom Hurricane Heat Cool & Defrost System for 1967-68 Mercury Cougar / Ford Mustang with original 289 V-8 with or w/o Power Steering. Easy to Install! Hurricane Unit mounts to firewall in place of factory heater, a/c & heater fittings pass neatly through original blower motor hole with custom rubber grommet. Electronic switching package includes correct reproduction A/C Control bezel w/ louvers. Electronic...

Reproduction set of color coded A/C rubber hoses, two T connectors and vacuum diagram.

Used A/C suction service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Used A/C discharge service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Used stamped steel single groove alternator pulley, typically these are described as being 2-7/8 inches in diameter. We find various casting numbers on them, such as: C5AF-10A352-F1, C5AF-10A352-G1, C5AF-10A352-K, C5AF-10A352-L.Replaces Ford part number C5AZ-10344-K.

This is a 'made in China' wiring harness. Quality is OK and will work for this application. Application is 1967-68 Mercury Cougar XR7 models and Ford Mustang without factory tachometer option, all with 289 or 302 engines. *Caution, not for use with Cougar standard models or Mustang with alternator warning light. *Note - Excludes California models or cars with factory Thermactor smog pump with low mounted alternators.Replaces Ford Part # C7ZZ-14305-B Door Tag 65B

Reproduction alternator wiring harness for all 1967 Mercury Cougar Standard Models, meaning Non XR7. Additionally 1967 Ford Mustang with tachometer. Excellent reproduction copied from an NOS wiring harness.Ford service number C7ZZ-14305-E, wire harness marked C7ZB-14305-E.

Nice reproduction of the original alternator wiring harness, has individual colored boots and wire colors match up to the original Ford drawings. Application is 1967 Mercury Cougar standard models or 1967 Ford Mustang with factory tachometer option, all with S code 390-4V engines. Ford service part number C7ZZ-14305-D, original harness numbered C7ZB-14305-D. *Caution, not for use with Cougar XR7 models or Mustang with ammeter gauge. *Note - Excludes California models with Thermactor smog pump...

Nice reproduction of the original alternator wiring harness, has individual colored boots and wire colors match up to the original Ford drawings. Application is 1967 Mercury Cougar XR7 models or 1967 Ford Mustang with factory tachometer option, all with 390-4V engines. Ford service number C7ZZ-14305-C, original wire harness marked C7ZB-14305-C. *Caution, not for use with Cougar standard models or Mustang with alternator warning light.*Note - Excludes California models or cars with factory...

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...

Air conditioning belt tension pulley for 1967 Cougars and Mustangs with the 390 engine. Also fits 1967 ford Thunderbird and other Ford and Mercury with 390, 410, or 428 engines. These are all sold with new bearings. If your pulley only needs a bearing, we have those too. Used with C7ZZ-2888-A, which is the steel lateral support brace for 1967 Cougars and Mustangs with the S code 390 engine. Two versions of this pulley were made by Ford, the difference is the pulley itself. Some pulleys,...

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Steel elbow that uses the A/C coupler from the liquid or sight glass hose to the dryer. This is an OEM Ford part that was originally part of an assembly, which included the sight glass hose, coupler, and this elbow. This elbow has the flared fitting common to the 1967-68 A/C connections. We recommend replacing "O" rings prior to installation, which are commercially available from air conditioning service centers.

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-7/8 inches, sometimes mentioned as 3.15" overall. Applications include 1967-68 Mercury Cougar and Ford Mustang with 289/302 and standard cooling. Reference number YA-79.Ford part # C5OE-8546-A, Ford engineering # C5OZ-8546-A.

Fan spacer, measuring 3-1/16 inches, sometimes mentioned as 3.40" overall. Applications include 1967 Mercury Cougar and Ford Mustang with 289-4V. Reference number YA-78.Ford part # C5AE-8546-B, Ford engineering # C5AZ-8546-B.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.

Ford part number C5AZ-6312-B. Application for 1967-68 289 and 302 engines without all of the following; air conditioning, power steering, California thermactor smog. The alternator would also have a single sheave pulley. Ford casting number C5AE-6312-A. Single sheave crank shaft pulley. About 6-5/16 inches in diameter.

C5AZ-6312-D Application for 1967-68 289 or 302 engines with air conditioning. Power steering and or California Thermactor emissions permissible. Ford casting number C5AE-B. Triple sheave 67 68 crank pulley. Inner diameters are about 6-1/2 inches, outer diameter is 7-5/16 inches.

C5AZ-6312-E Application 289 engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6 5/16" wide 3" deep to mounts.  Ford casting number C7AE-6312-A. Double sheave 67 crank pulley.

Ford casting number C5TE-6312-A. Single cast iron pulley for use with California thermactor emissions and low mount dual alternator pulleys. No other options, just the DSO 52 and 53 California engines. Ford Master Part number C5TZ-6A312-A. 6-5/8 inches in diameter. Together with the inner crankshaft balancer pulley, these now paired pulleys drive both the water pump and alternator pulleys. The Thermactor air pump pulley is driven by the 3rd outer water pump pulley sheave - only. Must use the...

Casting number C5AE-D. Triple sheave pulley used with both air conditioning and thermactor emissions. Inner pulley fits over the harmonic balancer, largest pulley is 7-3/4 inches in diameter. *Note - with the inclusion of this larger diameter pulley you must use timing pointer part number C5AE-6023-A.

Ford casting number C1AE-6312-A. Cast iron double sheave pulley. 6-5/8" and 6.00" in diameter. Ford cast number C1AE-6312-A. For use with power steering and air conditioning or with California thermactor emissions, either or, not both.

C5AZ-8509-J For use originally on 1967 289 engines without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single belt pulley 6.10 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.*This is one of the few water pump pulleys that did not have an imprinted casting number. Originally this pulley had an ink stamp. We will most likely be...

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

C7AZ-8509-E 289/302 Water Pump Pulley-Used C7AZ-8509-E Thermactor emission systems. Application also includes 1969 Boss 302 Eliminator. All applications are without air conditioning. With or without power steering. Triple sheave pulley all equal diameter at 6-7/16 inches. Ford casting number C7OE-8509-B. *1967 application with standard cooling (17 inch radiator) *After 11-13-1966

Water pump pulley 1 sheave, about 6.11 inches. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches. Application include 1967 Cougar with 289. 1969 Cougar and Mustang with 390-4V. Also various Mustangs 1965-67, all with 289.Replaces Ford casting number C5OE-8509-A.

For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. 2 sheaves with a diameter of 5-7/8 inches. This is a good copy of the original water pump pulley, it has no stamped part number.Replaces   C6AZ-8509-A or C6AE-8509-A.

Core bench seat for the 1967 Mercury Cougar or Ford Mustang equipped with decor interior. The foam almost will always be deteriorating or even missing. All seat cores will be solid frames taken from a Western parts car. Seat tracks are sold separate.

Bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. We highly recommend used cores as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Driver side shown.

Bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. We highly recommend used cores as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Driver side shown.

Complete seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. We highly recommend used cores as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Driver side shown.

Complete seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. We highly recommend used cores as they are more correct and significantly less expensive. These are dropshipped directly from the manufacturer. Driver side shown.

Used passenger side bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. Most times customers will only need the bottom portion, and it saves on shipping costs compared to shipping a whole seat frame.

Used driver side bottom seat frame for the 1967 Cougar or the 1965 - 1967 Mustang all models with standard or Décor bucket seats. Most times customers will only need the bottom portion, and it saves on shipping costs compared to shipping a whole seat frame. 

Comes with all parts shown for one bucket seat, good quality but not as good as original FoMoCo parts. Make sure and check out our good used originals. Replaces Ford part numbers C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A.

C7AZ-6A312-A. Double or two groove crankshaft pulley. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. 6-1/8 inches in diameter. 1967 Application - Mercury or Ford 289 with automatic transmission and standard cooling (17 inch radiators). Without air conditioning and without power steering. 1968 Application - Mercury or Ford 289 or 302 with or without power steering. Thermactor emissions permissible. Ford casting number C7OE-6312-A. Double sheave 67 68 crank pulley. ...

New crank shaft pulley with 2 sheaves for any 3 bolt, 289 / 302 / 351W engines with power steering and the single belt alternator pulley. Without air conditioning, and without emissions.   6-3/8" overall diameter, has 3/8 and 1/2 inch grooves for fan belts. Replica of the C7AE-6312-A crankshaft pulley by Ford. Double sheave 67 crank pulley.

For use originally on 1967 289 engines with California emissions (All 1967 DSO 52 and 53 Mercury Cougars), and without factory air conditioning. With extra cooling (20 inch wide radiator). 3 sheave pulley (three fan belts), with pulleys having diameters of 4-7/16 inches and 5-7/8 inches. Ford casting number C6OE-8509-A, was probably an ink stamp. These pulleys were made using a double sheave C6AE-8509-A pulley with a second smaller pulley welded on.

C6AZ-8509-F With air conditioning. Power steering and or thermactor emissions possible. 2 sheaves or 2 fan belts with a diameter of about 5-5/16 inches. Ford casting number C6OE-8509-B.

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

Sold in a set of eight, these are the same gauge steel as originals. Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Replaces Ford Part # C5ZZ-13190-K

This adjustable linkage kit connects the left track to the right track on a bucket seat. Original Ford part number C5ZZ-6561726-A. Ford description: Rod - Front Seat Track Tie. Listed for bucket seats 1965-1970.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Correct for 1967 but fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. We also have the version with rectangular plates at the studs if you are wanting to match what you may have currently. ...

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This kit fits the 1967 with a 1/4" control Valve Pressure fitting. You might want to verify that your 67 has the 1/4" fitting as many have been upgraded the the 5/16" fitting. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

[No Description Provided]

Band or ring style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Comes with a course sheet metal type threaded hex head bolt. Ford part number C5DA-5A272-B. *Note all 1967 & 1968 Cougars had 2 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C6AA-5A272-A is the factory style 2-1/4" tailpipe clamp.

Add this item to your cart to download a free pdf copy of these instructions. On Checkout you will receive a link to download it! We've recreated this document from an original, being careful to keep the layout and font the same. Plain text version below: TECHNICAL INSTRUCTION (ATTACHMENT III TO SPECIAL SERVICE LETTER) Ford Division Service Campaign H-18 Lincoln-Mercury Division Service Campaign C-07 Power Brake Booster Replacement - 1967 Mustang with Power Disc Type Brakes - Booster Kit C...

Master clip kit which includes the following fasteners:Engine bayEngine feedFirewallFront crossmemberParking lightsPassenger side apron below relayRadio cable to dashKeep in mind that not all fasteners found on 1967 Courgars / Mustangs are in this kit.

Reproduction bolts and washers for the manual transmission bell housing on any 1967-68 Cougar or Mustang equipped with a 289 / 302 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1967-68.

Reproduction Smog Pump Pully Bolt for the 1967 - 1968 Mercury Cougar or Ford MustangSold individually 

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Replaces Ford Part # 359747-S

Sold as a Kit as Pictured.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

Used grade B trim / Beauty ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 14x6" 1968 SS wheel. This ring will have small scratches and or dings that will not be very noticeable.  Sold individually, four required per car as the spare did not come equipped with a center cap or trim ring. Replaces Ford part number C6ZZ-1210-A. ...

Used grade A trim ring for a 1967 Cougar style steel wheel. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep, one year only wheel. Looks very similar to the 1968 SS wheel. No dings or scratches that cannot be buffed out. sold individually.Replaces Ford part number C6ZZ-1210-A.

Another great free download for you, our customer! In this free download, John Brower guides you through the installation of an overlay on your dashboard on your Mercury. Simply add this item to your cart and you will receive the download link via email after you complete the order.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

Sold individually. Zinc (dark silver)

Self threading white plastic. Used on front and rear valances.Sold individually.

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.